ADA BRICK PATTERN WET SET PANEL Product Features Detectable Warning Panels

ADA BRICK PATTERN
WET SET PANEL
®
Detectable Warning Panels
3 BRICK PATTERNS AVAILABLE:
• Basket Weave (shown)
• Herringbone
• Running Bond
Product Features
• ADAAG Compliant
• Approved by most DOT’s
• 5 Year Manufacturer Warranty
• Installs in Less than Half the
Time of Standard Pavers
• Very high Impact Resistance
• Exceptional Strength
• Extremely Durable
• Outlasts and Out-performs
All Traditional Pavers
• No Plant Life or Weed Growth
Between Pavers
• No Elevation Deviation of Brick Height
Due to Expansion & Contraction
• Polymer Concrete Material
• Homogenous Colors
• Comes Fully Assembled
• Color Matching Bolts
• Easy to install
• Simple to Replace
Wet Set Panel Specifications
PATTERN STYLE
SIZE W x L x D
PART NUMBER
PART
WEIGHT
PALLET
QTY.
BASKET WEAVE
RUNNING BOND
HERRINGBONE
24” x 48” x 1/2”
A6002448BRADA-XX
A6002448RRADA-XX
A6002448HRADA-XX
45 lbs.
45 lbs.
45 lbs.
15
15
15
www.armorcastprod.com
24” x 48” x 1/2”
24” x 48” x 1/2”
TEL: (818) 982-3600 FAX: (818) 982-7742
ADA BRICK PATTERN
WET SET PANEL INSTALLATION
®
Detectable Warning Panels
Recommended Wet Set Panel
Instructions:
1. Follow all safety requirements that include but not
limited to, State, Federal and/or Local safety standards.
2. Concrete mix shall conform to all requirements as
specified by the contract document.
3. Tools required for installation are typical of those used
by concrete finishers.
4. Do not remove the anchors or bolts before placement.
Panel shall be placed in concrete with all the
hardware attached.
5. After concrete is poured the contractor shall establish
finished grade using mason line or other appropriate
methods. The polymer concrete panel shall be placed
on top of the concrete and tamped in place using
installer’s weight or concrete vibrator to facilitate
placement in a low slump concrete.
Final panel elevation shall be verified.
Replaceable Panels
Replacement Instructions:
1. Simply unscrew bolts from panel.
2. Pry panel up and lift away.
3. Clean surface area.
4. Replace with new panel.
5. Screw bolts back into anchors.
6. Make sure the proper slope is obtained as specified
in the contract document.
7. Low slump concrete may require 25 to 50 pound weights
to weigh down panels after placement in concrete.
8. Steel edging trowel with a minimum of 1/8” radius shall be
used to edge the finished concrete around the panel.
1/2” deep groove is required.
Enlarged view
DISTRIBUTED BY:
9. Once concrete is hardened, remove weights and panel
protective cover.
10. Protect the installed tiles from pedestrian and vehicular
traffic until concrete is hardened.
Wet Set Panel Technical Data
TEST DESCRIPTION
Water Absorption @ 100˚ C
Slip Resistance
Compressive Strength
Tensile Strength
Flexural Strength
Chemical Resistance
Abrasive Wear
Surface Flammability
Smoke Density
Flame - Rate of Burning
Gardner Impact Geometry
Hardness - Shore D
Accelerated Service Test
Freeze Thaw
Fungus Resistance Test
Salt Spray
www.armorcastprod.com
VALUE (Nominal)
TEST METHOD
ASTM
ASTM
ATSM
ATSM
ATSM
ATSM
ATSM
ATSM
ATSM
ATSM
ATSM
ATSM
ASTM
ATSM
ATSM
ATSM
D570
C1028
D695
D638
D790
D543
D2486
E162
E662-03
D635-91
D5420 w/ Geometry “GE”
D2240
G154 “Cycle 4”
C1026-87 (2002)
G21
B117-03
0.35%
0.80 Minimum
24,000 PSI
11,000 PSI
Yields at 6,000 PSI, No Failure
No dissolution under common chemicals
0.020 inches max. after 1,000 abrasive cycles
Less than 25
Less than 0.4 @ 1% / Less than 14 @ 4%
Self Extinguishing
110 IN-LB, or 450 IN-LB/IN (min.)
75
<3 Delta E w/No Deterioration after 3,000 hrs.
No Disintegration
No Growth
No Deterioration
TEL: (818) 982-3600 FAX: (818) 982-7742
`