GOGO KIDZ® TRAVELMATE - Go

GOGO KIDZ ®
TRAVELMATE
MODEL QRKIDZ
®
ASSEMBLY &
ATTACHING GUIDE
when you and your baby are “on the go”
7013 Realm Drive Suite C San Jose, CA 95119 / p (408) 360.0653 / f (408) 360.7967 / www.gogobabyz.com
Go-Go Babyz® Corporation
PA R T S
A S S E M B LY
A
*You will need a Philips Head Screwdriver or electric drill for Handle Screws
A.
Handle (1)
1.
Insert the Handle (A) into the Plate (C)
B.
Handle Screws (2)
2.
Align pre-drilled holes at the bottom
C.
Plate (1) with Quick Release Strap Attached
of the Handle with holes in front of
D.
Axle (1)
Plate (It is okay of holes do not align perfectly
E.
Wheels (2) with Quick Release Spring Locks (2)
they are to be used as a guide)
B
C
3.
Insert Handle Screws (B) in front of Plate
4.
Pull up on Handle to ensure it is secured
5.
Insert Axle (D) through opening at
Ladder
Strap
Adjusting
Clip
bottom of Plate
D
6.
Slide Wheel with Quick Release
Front of plate
Spring Locks (E) on to each side of
Axle, push on Spring Lock until wheel
snaps in place
E
Buckle /
Ratchet
Strap
7.
Test connection by pulling on
Wheels to ensure they are secured
Metal Brackets &
Binding Posts
01
02
PA R T S
A S S E M B LY
A
*You will need a Philips Head Screwdriver or electric drill for Handle Screws
A.
Handle (1)
1.
Insert the Handle (A) into the Plate (C)
B.
Handle Screws (2)
2.
Align pre-drilled holes at the bottom
C.
Plate (1) with Quick Release Strap Attached
of the Handle with holes in front of
D.
Axle (1)
Plate (It is okay of holes do not align perfectly
E.
Wheels (2) with Quick Release Spring Locks (2)
they are to be used as a guide)
B
C
3.
Insert Handle Screws (B) in front of Plate
4.
Pull up on Handle to ensure it is secured
5.
Insert Axle (D) through opening at
Ladder
Strap
Adjusting
Clip
bottom of Plate
D
6.
Slide Wheel with Quick Release
Front of plate
Spring Locks (E) on to each side of
Axle, push on Spring Lock until wheel
snaps in place
E
Buckle /
Ratchet
Strap
7.
Test connection by pulling on
Wheels to ensure they are secured
Metal Brackets &
Binding Posts
01
02
AT TA C H I N G T O Y O U R C A R S E AT
NOTE: The Quick Release Strap is pre-assembled onto the plate of the gogo Kidz Travelmate
for use with most car seats. You may need to make adjustments in the length of the strap
or the position the strap is located on the gogo Kidz Plate. If so, please refer to page 5.
Place car seat face down on floor. *
Locate the two ribs on each side of your car seat .
Align the two support Tabs at the bottom of the gogo Kidz Plate with bottom of ribs
(or the bottom of base).
NOTE: Some car seats require the Tabs of the gogo Kidz Plate to go under the base not the car seat ribs. Do not attach to base on Britax car seats. If your car seat has a
removable base, you may need to remove the base prior to attaching the gogo Kidz
Travelmate.
4.
Lay the gogo Kidz Plate flat on top of the back of the car seat.
5.
Take the Ladder Strap (long side of the strap - already attached to the
gogo Kidz Plate) and insert through the same opening you would put your
car seat belt in the forward facing position.
6.
Insert Ladder Strap into the buckle located on opposite side of the gogo Kidz
Plate and use ratchet to tighten. Tighten securely, but DO NOT OVERTIGHTEN.
7.
Pick up your car seat by the Handle of the gogo Kidz Travelmate.
8.
Test connection by releasing the Handle into the upright position and
pulling /pushing your seat around the room.
9.
If your car seat has a tether strap, pull 10” of strap out and pull over handle
attaching tether latch to plate handle, tighten strap.
P L A C E R AT
IMAGES OF GOGO KIDZ STRAP
G O I N G T H R O U G H C A R S E AT.
1.
2.
3.
•After the first time you attach and are familiar with the product, you may also
attach the gogo Kidz Travelmate to a car seats while in an upright position
03
and with a child sitting in the car seat.
Car seat resting on Tabs of the gogo
Kidz Travelmate Plate. Ladder Strap
going through forward facting seat
belt hole.
Ladder Strap coming through other
side of car seat.
Quick Release Strap going all the
way through opening in car seat.
Ladder Strap inserted into ratchet
buckle.
04
AT TA C H I N G T O Y O U R C A R S E AT
NOTE: The Quick Release Strap is pre-assembled onto the plate of the gogo Kidz Travelmate
for use with most car seats. You may need to make adjustments in the length of the strap
or the position the strap is located on the gogo Kidz Plate. If so, please refer to page 5.
Place car seat face down on floor. *
Locate the two ribs on each side of your car seat .
Align the two support Tabs at the bottom of the gogo Kidz Plate with bottom of ribs
(or the bottom of base).
NOTE: Some car seats require the Tabs of the gogo Kidz Plate to go under the base not the car seat ribs. Do not attach to base on Britax car seats. If your car seat has a
removable base, you may need to remove the base prior to attaching the gogo Kidz
Travelmate.
4.
Lay the gogo Kidz Plate flat on top of the back of the car seat.
5.
Take the Ladder Strap (long side of the strap - already attached to the
gogo Kidz Plate) and insert through the same opening you would put your
car seat belt in the forward facing position.
6.
Insert Ladder Strap into the buckle located on opposite side of the gogo Kidz
Plate and use ratchet to tighten. Tighten securely, but DO NOT OVERTIGHTEN.
7.
Pick up your car seat by the Handle of the gogo Kidz Travelmate.
8.
Test connection by releasing the Handle into the upright position and
pulling /pushing your seat around the room.
9.
If your car seat has a tether strap, pull 10” of strap out and pull over handle
attaching tether latch to plate handle, tighten strap.
P L A C E R AT
IMAGES OF GOGO KIDZ STRAP
G O I N G T H R O U G H C A R S E AT.
1.
2.
3.
•After the first time you attach and are familiar with the product, you may also
attach the gogo Kidz Travelmate to a car seats while in an upright position
03
and with a child sitting in the car seat.
Car seat resting on Tabs of the gogo
Kidz Travelmate Plate. Ladder Strap
going through forward facting seat
belt hole.
Ladder Strap coming through other
side of car seat.
Quick Release Strap going all the
way through opening in car seat.
Ladder Strap inserted into ratchet
buckle.
04
QUICK RELEASE STRAP
ADJUSTMENTS
NOTE: The Quick Release Strap on the gogo Kidz has been assembled in the most common
position, to fit most car seats. Once the gogo Kidz Travelmate has been properly attached to
a car seat, it should not move or slide around. Your car seat should easily roll freely once
tilted back on the gogo Kids Travelmate wheels. If not, please adjust either the length of the
strap for more tension or the position of the strap on the gogo Kidz Travelmate. The strap
should be level with the forward facing car seat belt opening.
TO ADJUST THE TENSION: Remove gogo Kidz Travelmate from your car seat. Adjust the strap
with the adjusting clip. Reattach to your car seat and make sure when tightening the ratchet
that the ladder strap is not able to tighten all the way to the base of the ladder strap.
S P E C I A L I N S T R U C T IPOLNASC E/ RSAI T
DE
N O T E S O N S O M E C A R S E AT S
Cosco Alpha Omega Series
The Alpha Omega 3-in-1 car seat has a removable base for certain situations such as
airline use. The gogo Kidz Travelmate only fits with the base removed.
Evenflo Triumph
To attach to the Evenflo® Triumph car seat you will use with the strap all the way
extended and the Triumph seat all the way in the reclined position.
The car seat should be adjusted to lean all the way back, otherwise; child will be too
vertical. Follow remaining instructions inside guide.
Adjusting
Clip
Metal
Brackets
TO ADJUST THE STRAP HEIGHT: Remove
the metal brackets that attach the strap
to the gogo Kidz Travelmate Plate with a
screwdriver. Reposition the bracket in
holes running down the side of the gogo
Kidz Travelmate Plate.
NOTE: Make sure you position both metal brackets in
same hole (ex: left side is fourth hole from the 05
top and right side is fourth hole from the top.
06
QUICK RELEASE STRAP
ADJUSTMENTS
NOTE: The Quick Release Strap on the gogo Kidz has been assembled in the most common
position, to fit most car seats. Once the gogo Kidz Travelmate has been properly attached to
a car seat, it should not move or slide around. Your car seat should easily roll freely once
tilted back on the gogo Kids Travelmate wheels. If not, please adjust either the length of the
strap for more tension or the position of the strap on the gogo Kidz Travelmate. The strap
should be level with the forward facing car seat belt opening.
TO ADJUST THE TENSION: Remove gogo Kidz Travelmate from your car seat. Adjust the strap
with the adjusting clip. Retach to your car seat and make sure when tightening the ratchet
that the ladder strap is not able to tighten all the way to the base of the ladder strap.
S P E C I A L I N S T R U C T IPOLNASC E/ RSAI T
DE
N O T E S O N S O M E C A R S E AT S
Cosco Alpha Omega Series
The Alpha Omega 3-in-1 car seat has a removable base for certain situations such as
airline use. The gogo Kidz Travelmate only fits with the base removed.
Evenflo Triumph
To attach to the Evenflo® Triumph car seat you will use with the strap all the way
extended and the Triumph seat all the way in the reclined position.
The car seat should be adjusted to lean all the way back, otherwise; child will be too
vertical. Follow remaining instructions inside guide.
Adjusting
Clip
Metal
Brackets
TO ADJUST THE STRAP HEIGHT: Remove
the metal brackets that attach the strap
to the gogo Kidz Travelmate Plate with a
screwdriver. Reposition the bracket in
holes running down the side of the gogo
Kidz Travelmate Plate.
NOTE: Make sure you position both metal brackets in
same hole (ex: left side is fourth hole from the 05
top and right side is fourth hole from the top.
06
GOGO KIDZ ®
TRAVELMATE
MODEL QRKIDZ
®
ASSEMBLY &
ATTACHING GUIDE
when you and your baby are “on the go”
7013 Realm Drive Suite C San Jose, CA 95119 / p (408) 360.0653 / f (408) 360.7967 / www.gogobabyz.com
Go-Go Babyz® Corporation
`