THIRD GENERATION RESIDUAL GAS IONIZATION PROFILE MONITORS AT FERMILAB* J.R. Zagel#, M. Alvarez, B. Fellenz, C. Jensen, C. Lundberg, E. McCrory, D. Slimmer, R. ThurmanKeup, D. Tinsley, FNAL, Batavia, IL 60510, USA Abstract The latest generation of IPM's installed in the Fermilab Main Injector and Recycler incorporate a 1 kG permanent magnet, a newly designed high-gain, rad-tolerant preamp, and a control grid to moderate the charge that is allowed to arrive on the anode pick-up strips. The control grid is intended to select a single Booster batch measurement per turn. Initially it is being used to allow for a faster turn-on of a single, high-intensity cycle in either machine. The expectation is that this will extend the Micro Channel Plate lifetime, which is the high-cost consumable in the measurement system. We discuss the new design and data acquired with this system. INTRODUCTION Previous generations of residual gas ionization profile monitor’s (IPM’s) have been in operation, both at Fermilab and other laboratories, for many years [1-3]. The second-generation system applied a fixed permanent magnetic field, and polarity change to collect electrons to reduce space charge effects in the measurement [4]. Its field quality, while sufficient to improve the measurements, was not quite 1 kG, and required 4 feet of beam line to accommodate the magnetic unit. Two primary issues that arise have been the Micro Channel Plate (MCP) lifetime, and saturation effects of too much charge required from them. The third generation is designed to improve on these deficiencies. WHAT’S NEW The new system incorporates the improvements added to the Fermilab Tevatron IPM [5] along with a few new features. New Magnet Design The new magnet is designed using SmCo5 permanent magnets. This material was chosen to give the highest residual magnetic field (Br) with the lowest variation in temperature dependence, at a reasonable cost and availability. A standard brick is 1" by 2" by 1/2". The magnet was intended to provide 1 kG in the detector area, with the return flux half upstream and half downstream, and shimmed, such that the beam sees a total integrated field of zero. The magnet is 31.5”L x 14”D with a minimum aperture of 4.25” to allow for a 4” diameter beam pipe suitable to both horizontal and vertical planes in the Main Injector and Recycler. Magnet design, modeling, and measurement details have been presented in [6]. MEASUREMENT TIMING The new system uses a timing module that combines the function of our Universal Clock Decoder (UCD), and the VME RF Timing module (VRFT). This module decodes the lab-wide timing 10 MHz clock (TCLK), the machine specific, beam synchronous clock (BSYNC), and a Machine Data (MDAT) Reference System, and outputs a clock trigger. Utilizing this board, we can generate a trigger on a specific machine state, and a particular machine clock cycle that then enables the beam synchronous clock pulses to gate our ADC’s. The resolution of this trigger is one 53 MHz bunch. One sample per turn is generally acquired for a range of turns specified in the measurement specification. Multiple samples per turn is also a supported mode of operation. ___________________________________________ * Operated by Fermi Research Alliance, LLC under Contract No. DeAC02-07CH11359 with the United States Department of Energy. # [email protected] Figure 1: Recycler Vertical Installation Anode Strip Board The anode strip pick-up board for both Main Injector and Recycler is a ceramic circuit board with 120 copper strips spaced at 0.5mm. The copper occupies 80% of that pitch with 20% space between strips. All signals are connected via 20 pin, ceramic mounted, quick release connectors. A multilayer flexible circuit delivers these signals to 6 front flange feed through connectors. A “Flash Test” strip has been added to the bottom of the arXiv:1502.02901v1 [physics.ins-det] 10 Feb 2015 A pilot study of the novel J-PET plastic scintillator with 2-(4-styrylphenyl)benzoxazole as a wavelength shifter A. Wieczoreka, b , P. Moskala , S. Nied´zwieckia , T. Bednarskia , P. Bialasa , E. Czerwi´ nskia , A. Danelc , A. Gajosa , A. Gruntowskia , D. Kami´ nskaa , L. Kaplona, b , A. Kochanowskid , G. Korcyla , a J. Kowal , P. Kowalskie , T. Kozika , W. Krzemie´ na , E. Kubicza , M. Molendad , M. Palkaa , L. Raczy´ nskie , Z. Rudya , O. Rundela , a a P. Salabura , N.G. Sharma , M. Silarskia , A. Slomskia , J. Smyrskia , A. Strzeleckia , T. Uchaczd , W. Wi´slickie , M. Zieli´ nskia , N. Zo´ na a Faculty of Physics, Astronomy and Applied Computer Science, Jagiellonian University b Institute of Metallurgy and Materials Science, Polish Academy of Sciences c Institute of Chemistry and Physics, University of Agriculture d Faculty of Chemistry, Jagiellonian University e´ Swierk Computing Centre, National Centre for Nuclear Research February 11, 2015 Abstract For the first time a molecule of 2-(4-styrylphenyl)benzoxazole containing benzoxazole and stilbene groups is applied as a scintillator dopant acting as a wavelength shifter. In this article a light yield of the plastic scintillator, prepared from styrene doped with 2 wt% of 2,5-diphenylbenzoxazole and 0.03 wt% of 2-(4-styrylphenyl)benzoxazole, is determined to be as large as 60% ± 2% of the anthracene light output. There is a potential to improve this value in the future by the optimization of the additives concentrations. 1 Introduction Scintillators are widely used as detectors of radiation in many fields of science and industry. For example they are crucial components of apparatus used in nuclear and particle physics experiments, medical diagnostics modalities as well as radiation detectors in many sectors of homeland security [1] Scintillators play an important role in most of the nuclear imaging devices such as e.g. Positron Emission Tomography device (PET). Though PET is well 1 Monte Carlo Study of a 137Cs calibration field of the China institute of atomic energy GAO Fei a,b,* a Radiation Metrology Division, China Institute of Atomic Energy, Beijing, 102413, China b National Key Laboratory for Metrology and Calibration Techniques, Beijing, 102413, China Abstract The MCNP code was used to study the characteristics of gamma radiation field with collimated beam geometry. A close-to-reality simulation model of the facility was used for calculation air-kerma along the whole range of source-detector-distance (SDD) along the central beam and air-kerma off-axis beam profiles at two different source-detector-distance (SDD). The simulation results were tested by the measured results which were acquired in the Radiation Metrology Center of CIAE. Other characteristics such as the individual contributions of photons scattered in collimator, floor, walls, mobile platform and other parts of the irradiation halls to the total air kerma rate on the beam axis were calculated for the purpose of future improvement of metrological parameters in CIAE. Finally, factors which influence the simulation results were investigated, including e.g., detector volume effects or source density effects. Key Words Monte Carlo, MCNP, Simulation, Calibration, Air Kema, Radiation 1 Introduction Radiation Metrology Division of CIAE obtains many photon sources with different activity values for calibration, metrological research and design new dosimeters for detection and measurement of photon-related quantities. With these sources e.g. cesium-137, colbalt-60 and americium-241, it is possible to obtain air kerma rate from 0.2μGy /h up to 54Gy/h sufficient for all of commonly used dosimeters. Irradiation field shapes and scattered photons are the most important criterions for irradiation halls. So far, the longitudinal and lateral field shapes in air kerma rate were measured by secondary ionization chambers. The development of computer technology made it possible to use sophisticated mathematical models to calculate relative parameters of the irradiation fields. In this study, a MCNP-4C Monte Carlo code model of cesium-137 irradiation hall was used for beam profiles verification and for the assessment and analysis of scattered air kerma, which is very important for future improvement of metrological parameters of photon beams in CIAE . 2 Experiments For the purpose of routine measurements, the longitudinal profiles in air kerma rate at distances from 1m to 6.5m from the 137Cs source were measured with a spherical ionization chamber PTW 32002. The transversal beam profiles were measured in a horizontal line perpendicular to the beam axis at two distances of 1m and 2m from the 137Cs source. For these measurements，an ionization chamber NE 30c. c. (Nuclear Enterprises ) was used due to its smaller volume (outer diameter is about 4cm ). * Corresponding author:[email protected] 3 Simulations 1 EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH (CERN) CERN-PH-EP/2015-006 2015/02/11 arXiv:1502.02702v1 [physics.ins-det] 9 Feb 2015 CMS-EGM-14-001 Performance of photon reconstruction and identification with the CMS detector √ in proton-proton collisions at s = 8 TeV The CMS Collaboration∗ Abstract A description is provided of the performance of the CMS detector for photon reconstruction and identification in proton-proton collisions at a centre-of-mass energy of 8 TeV at the CERN LHC. Details are given on the reconstruction of photons from energy deposits in the electromagnetic calorimeter (ECAL) and the extraction of photon energy estimates. The reconstruction of electron tracks from photons that convert to electrons in the CMS tracker is also described, as is the optimization of the photon energy reconstruction and its accurate modelling in simulation, in the analysis of the Higgs boson decay into two photons. In the barrel section of the ECAL, an energy resolution of about 1% is achieved for unconverted or late-converting photons from H → γγ decays. Different photon identification methods are discussed and their corresponding selection efficiencies in data are compared with those found in simulated events. The measurement of the photon purity is described for one set of photon identification criteria. Submitted to the Journal of High Energy Physics c 2015 CERN for the benefit of the CMS Collaboration. CC-BY-3.0 license ∗ See Appendix A for the list of collaboration members EUROPEAN ORGANIZATION FOR NUCLEAR RESEARCH (CERN) CERN-PH-EP/2015-004 2015/02/11 CMS-EGM-13-001 arXiv:1502.02701v1 [physics.ins-det] 9 Feb 2015 Performance of electron reconstruction and selection with √ the CMS detector in proton-proton collisions at s = 8 TeV The CMS Collaboration∗ Abstract The performance and strategies used in electron reconstruction and selection at CMS −1 are presented based on data corresponding √ to an integrated luminosity of 19.7 fb , collected in proton-proton collisions at s = 8 TeV at the CERN LHC. The paper focuses on prompt isolated electrons with transverse momenta ranging from about 5 to a few 100 GeV. A detailed description is given of the algorithms used to cluster energy in the electromagnetic calorimeter and to reconstruct electron trajectories in the tracker. The electron momentum is estimated by combining the energy measurement in the calorimeter with the momentum measurement in the tracker. Benchmark selection criteria are presented, and their performances assessed using Z, Υ, and J/ψ decays into e+ +e− pairs. The spectra of the observables relevant to electron reconstruction and selection as well as their global efficiencies are well reproduced by Monte Carlo simulations. The momentum scale is calibrated with an uncertainty smaller than 0.3%. The momentum resolution for electrons produced in Z boson decays ranges from 1.7 to 4.5%, depending on electron pseudorapidity and energy loss through bremsstrahlung in the detector material. Submitted to the Journal of Instrumentation c 2015 CERN for the benefit of the CMS Collaboration. CC-BY-3.0 license ∗ See Appendix A for the list of collaboration members NJL model approach to diquarks and baryons in quark matter arXiv:1502.03084v1 [nucl-th] 10 Feb 2015 D. Blaschke Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland Bogoliubov Laboratory for Theoretical Physics, Joint Institute for Nuclear Research, RU-141980 Dubna, Russia E-mail: [email protected] A. Dubinin∗ Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland E-mail: [email protected] D. Zablocki Institute for Theoretical Physics, University of Wroclaw, 50-204; Wroclaw, Poland E-mail: [email protected] We describe baryons as quark-diquark bound states at finite temperature and density within the NJL model for chiral symmetry breaking and restoration in quark matter. Based on a generalized Beth-Uhlenbeck approach to mesons and diquarks we present in a first step the thermodynamics of quark-diquark matter which includes the Mott dissociation of diquarks at finite temperature. In a second step we solve the Bethe-Salpeter equation for the baryon as a quark-diquark bound state in quark-diquark matter. We obtain a stable, bound baryon even beyond the Mott temperature for diquark dissociation since the phase space occupation effect (Pauli blocking for quarks and Bose enhancement for diquarks) in the Bethe-Salpeter kernel for the nucleon approximately cancel so that the nucleon mass follows the in-medium behaviour of the quark and diquark masses towards chiral restoration. In this situation the baryon is obtained as a “borromean” three-quark state in medium because the two-particle state (diquark) is unbound while the three-particle state (baryon) is bound. XXII International Baldin Seminar on High Energy Physics Problems, 15-20 September 2014 JINR, Dubna, Russia ∗ Speaker. c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence. http://pos.sissa.it/ A. Dubinin NJL model for diquarks and baryons 1. Thermodynamics of correlations in quark matter While numerous works have recently studied the thermodynamics of quark matter on the mean-field level including the effects of the medium dependence of the order parameters, not so much is known beyond the mean field, about hadronic correlations and their backreaction to the structure of the model QCD phase diagram and its thermodynamics. Here we will elaborate on the generalized Beth-Uhlenbeck form of the equation of state which is systematically extended from studying mesonic correlations [1] to the inclusion of diquark degrees of freedom [2, 3]. To that end we will employ a Nambu–Jona-Lasinio-type quark model with fourpoint interactions in mesonic (quark-antiquark) and diquark (quark-quark) channels. We shall discuss here the importance of the interplay of the resonant states with the residual non-resonant ones in the continuum of scattering states. Due to the Levinson theorem both contributions have the tendency to compensate each other in quark matter above the Mott transition [4], see also [2, 3, 5, 6]. The most intriguing questions will occur when on the basis of this in-medium bosonized effective chiral quark model the next step of the hadronization program nucleon will be performed and diquarks will be “integrated out” in favor of baryons so that nuclear matter can be described in the model QCD phase diagram. A possible scheme for introducing baryons as quark-diquark bound states and integrating out the colored and therefore not asymptotically observable diquark fields has been suggested by Cahill and collaborators [7, 8, 9, 10]. It was afterwards elaborated by Reinhardt [11] and developed further by including the solitonic aspects of a field theoretic description of the nucleon [12]. However, the step to describe nucleonic many-body systems on this quark model basis has not been performed by these authors. Exploratory studies within the framework of an effective local NJL-type model for the quark-diquark interaction vertex have revealed a first glimpse at the modification of the nucleon spectral function in the different regions of the model QCD phase diagram, including chirally restored and color superconducting phases [13]. Again, the crucial step towards an equation of state for nuclear matter with this microscopic model for nucleons in the QCD phase diagram has not yet been done. We will prepare the ground for a Beth-Uhlenbeck description of nuclear matter, to be discussed in future work. In particular, at zero temperature the structure of a Walecka model for nuclear matter shall emerge under specified conditions. Earlier work in this direction [14, 15, 16] has demonstrated this possibility although no unified description of the nuclear-to-quark matter transition has been possible and the elucidation of physical mechanisms for the very transition between the hadronic and the quark matter phases of low energy QCD has been spared out. Or study aims at indicating directions for filling this gap by extending the discussion of the Mott mechanism for the dissociation of hadronic bound states of quarks within the NJL model description of low-energy QCD which has been given on the example ot two-particle correlations (mesons and diquarks) in [2] and sketching steps towards a Beth-Uhlenbeck description of nuclear matter where nucleons are treated as quarkdiquark correlations in quark matter [17]. 1.1 Quark matter thermodynamics in the NJL model We base the approach on the NJL model Lagrangian including vector and diquark interaction channels besides the standard scalar-pseudoscalar chirally symmetric interaction for the isospin symmetric case (µu = µd = µ and mu = md = m0 ) 2 Mon. Not. R. Astron. Soc. 000, 1–11 (2014) Printed 11 February 2015 (MN LATEX style ﬁle v2.2) Bringing the Galaxy’s dark halo to life T. Piffl1⋆ , Z. Penoyre2 , J. Binney1 1 Rudolf Peierls Centre for Theoretical Physics, Keble Road, Oxford OX1 3NP, UK Hall, University of Cambridge, Trinity Lane, Cambridge CB2 1TJ, UK arXiv:1502.02916v1 [astro-ph.GA] 10 Feb 2015 2 Trinity submitted to MNRAS on 19th January 2015 ABSTRACT We present a new method to construct fully self-consistent equilibrium models of multicomponent disc galaxies similar to the Milky Way. We define distribution functions for the stellar disc and dark halo that depend on phase space position only through action coordinates. We then use an iterative approach to find the corresponding gravitational potential. We study the adiabatic response of the initially spherical dark halo to the introduction of the baryonic component and find that the halo flattens in its inner regions with final minor-major axis ratios q = 0.75 – 0.95. The extent of the flattening depends on the velocity structure of the halo particles with radially biased models exhibiting a stronger response. In this latter case, which is according to cosmological simulations the most likely one, the new density structure resembles a “dark disc” superimposed on a spherical halo. We discuss the implications of these results for our recent estimate of the local dark matter density. The velocity distribution of the dark-matter particles near the Sun is very nonGaussian. All three principal velocity dispersions are boosted as the halo contracts, and at low velocities a plateau develops in the distribution of vz . For models similar to a state-of-the-art Galaxy model we find velocity dispersions around 155 km s−1 for vz and the tangential velocity, vϕ , and 140 – 175 km s−1 for the in-plane radial velocity, vR , depending on the anisotropy of the model. Key words: galaxies: kinematics and dynamics 1 INTRODUCTION It is now generally accepted that most of the rest mass in the Universe is contained in a type of “dark matter” that is incapable of electromagnetic interactions. Dark matter began to cluster gravitationally earlier than baryonic matter because it was decoupled from the cosmic radiation bath, which at redshifts > ∼ 1000 provided abundant pressure. Hence the formation of a galaxy starts with the accumulation of dark matter to form the dark halo. When and how baryons accumulated in the gravitational potential wells of dark halos is ill understood. In the simplest picture, they simply fell in dissipatively and formed stars near each halo’s centre, but this picture is inconsistent with the small fraction of baryons that are now in stars rather than intergalactic gas. Several lines of evidence indicate that the release of nuclear energy by early stars strongly attenuated the infall of baryons, thus increasing the extent to which galaxies are dark-matter dominated. The least dark-matter dominated galaxies are ones with luminosities similar to that, L∗, of our Galaxy: dwarf galax⋆ E-mail: tilmann.piﬄ@physics.ox.ac.uk c 2014 RAS ies are very strongly dark-matter dominated and stars play such a subsidiary role in the most massive dark-matter halos, those of galaxy groups and clusters, that we do not even recognise these halos as galaxies. Yet even in galaxies such as ours, it may be argued that the baryons have played a very subordinate role. Measurements of the optical depth to microlensing of stars located less than ∼ 10 deg from the Galactic centre imply that a signiﬁcant majority of the mass inside ∼ 3 kpc is concentrated in stars (Binney & Evans 2001; Bissantz et al. 2004). But the majority of the gravitational force that holds the Sun in its orbit comes from dark matter (e.g. Piﬄ et al. 2014, hereafter P14), and the dominance of dark matter increases sharply with increasing distance from the centre. Moreover, in galaxies such as ours and M33, we have reason to believe that most baryons accumulated in the potential well of the dark halo quiescently, forming a disc in centrifugal equilibrium (Mo et al. 1998). In our Galaxy, but not in M33, the central portion of the disc became unstable to the formation of a strong bar, which then buckled to form the Galaxy’s present bar/bulge (Combes & Sanders 1981; Raha et al. 1991). A dark halo will respond to the quiescent accumulation of baryons in a disc by distorting adiabatically: that arXiv:1502.02838v1 [physics.atom-ph] 10 Feb 2015 Constraints on extra dimensions from precision molecular spectroscopy E. J. Salumbides1,2 , A. N. Schellekens3,4,5 , B. Gato-Rivera3,5 , and W. Ubachs1 1 Department of Physics and Astronomy, and LaserLaB, VU University, De Boelelaan 1081, 1081 HV Amsterdam, The Netherlands 2 Department of Physics, University of San Carlos, Cebu City 6000, Philippines 3 Nikhef, Science Park 105, 1098 XG Amsterdam, The Netherlands 4 Institute for Mathematics, Astrophysics and Particle Physics, Radboud University, 6500 GL Nijmegen, The Netherlands 5 Instituto de Fisica Fundamental, CSIC, 28006 Madrid, Spain Abstract. Accurate investigations of quantum level energies in molecular systems are shown to provide a test ground to constrain the size of compactiﬁed extra dimensions. This is made possible by the recent progress in precision metrology with ultrastable lasers on energy levels in neutral molecular hydrogen (H2 , HD and D2 ) and the + + molecular hydrogen ions (H+ 2 , HD and D2 ). Comparisons between experiment and quantum electrodynamics calculations for these molecular systems can be interpreted in terms of probing large extra dimensions, under which conditions gravity will become much stronger. Molecules are a probe of space-time geometry at typical distances where chemical bonds are eﬀective, i.e. at length scales of an ˚ A. Constraints on compactiﬁcation radii for extra dimensions are derived within the Arkani-HamedDimopoulos-Dvali framework, while constraints for curvature or brane separation are derived within the Randall-Sundrum framework. Based on the molecular spectroscopy of D2 molecules and HD+ ions, the compactiﬁcation size for seven extra dimensions (in connection to M-theory deﬁned in 11 dimensions) of equal size is shown to be limited to R7 < 0.6µm. While limits on compactiﬁcation sizes of extra dimensions based on other branches of physics are compared, the prospect of further tightening constraints from the molecular method is discussed. PACS numbers: 04.50.-h, 33.20.Lg, 31.30.jf Submitted to: New J. Phys. The Hot QCD White Paper: Exploring the Phases of QCD at RHIC and the LHC arXiv:1502.02730v1 [nucl-ex] 9 Feb 2015 A White Paper on Future Opportunities in Relativistic Heavy Ion Physics February 11, 2015 Abstract The past decade has seen huge advances in experimental measurements made in heavy ion collisions at the Relativistic Heavy Ion Collider (RHIC) and more recently at the Large Hadron Collider (LHC). These new data, in combination with theoretical advances from calculations made in a variety of frameworks, have led to a broad and deep knowledge of the properties of thermal QCD matter. Increasingly quantitative descriptions of the quark-gluon plasma (QGP) created in these collisions have established that the QGP is a strongly coupled liquid with the lowest value of specific viscosity ever measured. However, much remains to be learned about the precise nature of the initial state from which this liquid forms, how its properties vary across its phase diagram and how, at a microscopic level, the collective properties of this liquid emerge from the interactions among the individual quarks and gluons that must be visible if the liquid is probed with sufficiently high resolution. This white paper, prepared by the Hot QCD Writing Group as part of the U.S. Long Range Plan for Nuclear Physics, reviews the recent progress in the field of hot QCD and outlines the scientific opportunities in the next decade for resolving the outstanding issues in the field. 1 Classical and Quantum Gauged Massless Rarita-Schwinger fields Stephen L. Adler∗ Institute for Advanced Study, Einstein Drive, Princeton, NJ 08540, USA. We show that, in contrast to known results in the massive case, a minimally gauged massless Rarita-Schwinger field yields consistent classical and quantum theories. To simplify arXiv:1502.02652v1 [hep-th] 9 Feb 2015 the algebra, we study a two component left chiral reduction of the massless theory. We formulate the classical theory in both Lagrangian and Hamiltonian form for a general nonAbelian gauging, and analyze the constraints and the Rarita-Schwinger gauge invariance of the action. An explicit wave front calculation for Abelian gauge fields shows that wavelike modes do not propagate with superluminal velocities. The quantized case is studied in covariant radiation gauge and axial gauge for the Rarita-Schwinger field, by both functional integral and Dirac bracket methods. The constraints have the form needed to apply the Faddeev-Popov method for deriving a functional integral in covariant radiation gauge. The Dirac bracket approach yields consistent Hamilton equations of motion in covariant radiation gauge, and leads to anticommutation relations with the correct positivity properties in axial gauge. We note that fermionic gauge transformations are a canonical transformation, but further details of the transformation between different fermionic gauges are left as an open problem. I. A. INTRODUCTION Motivations and Background Cancelation of gauge anomalies is a basic requirement for constructing grand unified models, and the usual assumption is that anomalies must cancel among spin 1 2 fermion fields. However, a 1985 paper of Marcus [1] showed that in principle an SU (8) gauge theory can be constructed with spin 3 2 Rarita-Schwinger fermions playing a role in anomaly cancelation, and we have recently constructed [2] a family unification model incorporating this observation. Using gauged spin 3 2 fields in a grand unification model raises the question of whether such fields admit a consistent quantum, or even classical theory. It is well known, from papers of Johnson and Sudarshan [3] and Velo and Zwanziger [4], and much subsequent literature, that theories of massive gauged RaritaSchwinger fields have serious problems. Does setting the fermion mass to zero eliminate these ∗ Electronic address: [email protected] What We Can Learn from the Running of the Spectral Index if no Tensors are Detected in the Cosmic Microwave Background Anisotropy M. Biagetti,1 A. Kehagias,1, 2 and A. Riotto1 1 arXiv:1502.02289v1 [astro-ph.CO] 8 Feb 2015 2 D´epartement de Physique Th´eorique and Centre for Astroparticle Physics (CAP), Universit´e de Gen`eve, 24 quai E. Ansermet, CH-1211 Geneva, Switzerland Physics Division, National Technical University of Athens, 15780 Zografou Campus, Athens, Greece (Dated: February 10, 2015) In this paper we operate under the assumption that no tensors from inflation will be measured in the future by the dedicated experiments and argue that, while for single-field slow-roll models of inflation the running of the spectral index will be hard to be detected, in multi-field models the running can be large due to its strong correlation with non-Gaussianity. A detection of the running might therefore be related to the presence of more than one active scalar degree of freedom during inflation. Motivations.— Inflation [1] provides a mechanism to explain the initial conditions for the Large Scale Structure (LSS) and for the Cosmic Microwave Background (CMB) anisotropy. The seeds for the density scalar perturbations are created from the quantum fluctuations “redshifted” out of the Hubble radius during the early period of superluminal expansion of the universe. At the same time, the generation of tensor (gravity-wave) fluctuations is a generic prediction of an accelerated de Sitter expansion of the universe [2]. To characterize the scalar and tensor perturbations several observables are introduced: the spectral index (or tilt) ns of the scalar perturbations, currently measured to be ns = 0.9655 ± 0.0062 at 68% CL; the running with the wavenumber k of the spectral index αs = dns /d ln k, currently consistent with zero, αs = −0.00571 ± 0.0071 at 68% CL (assuming no tensors); and the level of local non-Gaussianities parametrized by fNL = 0.8 ± 5.0 at 68% CL and gNL = (−9.0 ± 7.7) × 104 at 68% CL. All these figures are quoted from the last Planck releases [3, 4]. Finally, the tensor-to-scalar ratio is bounded to be r < 0.12 at 95% CL [5]. Many next-generation satellite missions, see for instance Refs. [6–8], are dedicated to measure the polarization of the CMB anisotropies. On large angular scales the B-mode polarization of the CMB carries the imprint of primordial gravitational waves, and its precise measurement would provide a powerful probe of the epoch of inflation. The goal of these missions is to achieve a measurement of r down to O(10−3 ). While a detection of gravity waves from inflation will be a major milestone for the inflationary paradigm, on the other hand one needs to remember that going from r = 10−1 down to r = 10−3 means testing the energy scale of inflation Einf only by a factor (100)1/4 ' 3.1 4 better than current bounds (r scales like Einf ). One should therefore envisage the situation in which Nature has not be so kind to us to set the scale of the energy of inflation within a factor of three away from the current limits. In this paper we will therefore operate under the working assumption that no tensors will be measured in the future by the dedicated experiments. While we hope this hypothesis will prove to be wrong in the future, we believe it is reasonable to ask how else we could learn something more about the inflationary perturbations. In this paper we turn our attention to the scale dependence of the tilt of the scalar perturbations. Our hypothesis on the tensor modes leads to a hardly detectable running within single-field slow-roll models. On the other hand, a negative result on tensors might indicate a low level of the Hubble rate, leaving open the possibility that the scalar perturbations are due to a light scalar field other than the inflaton field. In such a case, our findings indicate that a large running may be achieved thanks to an interesting correlation between the running and the level of non-Gaussianity. Such strong correlation exists only in multi-field models of inflation, while it is missing in single-field slow-roll models. If no tensors will be observed, a measurement of a sizable running of the spectral index might therefore imply a sizable amount of non-Gaussianity (and viceversa) and the presence of more than one active scalar degree of freedom during inflation. Our considerations are particularly relevant for the goals of next missions designed to measure the three dimensional structure of the universe, such as the ESA mission EUCLID [9] and the NASA SPHEREx mission [10], a proposed all-sky spectroscopic survey satellite. For instance, the combination of the galaxy power spectrum and bispectrum leads to the forecasted 68% CL errors σ(ns − 1) = 2.2 × 10−3 , σ(αs ) = 6.5 × 10−4 and σ(fNL ) = 0.2 (for the local case) in the case of SPHEREx. This is an improvement with respect to EUCLID forecasts of a factor ∼ 2 in αs and a factor ∼ 20 for the local fNL (or ∼ 6 with the galaxy power spectrum only). For the other parameters SPHEREx will deliver constraints comparable to those expected from the EUCLID spectroscopic survey. As EUCLID and (possibly) SPHEREx will strongly narrow down the allowed parameter space in the (αs , fNL )-plane, it is therefore extremely interesting and Noname manuscript No. (will be inserted by the editor) Variational Analysis of Mass Spectra and Decay Constants for Ground State Pseudoscalar and Vector Mesons in Light-Front Quark Model Ho-Meoyng Choi 1 , Chueng-Ryong Ji 2 , Ziyue Li 2 1 Department arXiv:1502.03078v1 [hep-ph] 10 Feb 2015 2 Department of Physics, Teachers College, Kyungpook National University, Daegu, Korea 702-701 of Physics, North Carolina State University, Raleigh, North Carolina 27695-8202 the date of receipt and acceptance should be inserted later Abstract Using the variational principle, we compute mass spectra and decay constants of ground state pseudoscalar and vector mesons in the light-front quark model (LFQM) with the QCD-motivated effective Hamiltonian including the hyperfine interaction. To avoid the issue of negative infinity in applying the variational principle to the computation of meson mass spectra, we smear out the Dirac delta function in the hyperfine interaction. We compare the results from this variational analysis with the previous computation handling the hyperfine interaction as perturbation. We also take a couple of different trial functions for the variation to examine the sensitivity of the variational results with respect to the choice of the trial wave functions. Comparing the results with the experimental data of mass spectra and decay constants for the ground state pseudoscalar and vector mesons from π to ϒ , we note that the analysis of the light meson sectors may need to be separately handled from the analysis of the heavy meson sectors as the degree of improvement in the LFQM results appears dependent on the meson sectors. 1 Introduction Effective degrees of freedom to describe a strongly interacting system of hadrons have been one of the key issues in understanding the non-perturbative nature of QCD in the low energy regime. Within an impressive array of effective theories available nowadays, the constituent quark model has been quite useful in providing a good physical picture of hadrons just like the atomic model for the system of atoms. Absorbing the complicated effect of quark, antiquark and gluon interactions into the effective constituent degrees of freedom, one may make the problem more tractable yet still keep some key features of the underlying QCD to provide useful predictions [1]. The effective potentials used in con- stituent quark models are typically described by the flux tube configurations generated by the gluon fields as well as the effective “one-gluon-exchange” calculation in QCD [2, 3]. In the QCD-motivated effective Hamiltonian, a proper way of dealing with the relativistic effects in the hadron system is quite essential due to the nature of strong interactions. In particular, proper care and handling of relativistic effects has been emphasized in describing the hadrons made of u, d, and s quarks and antiquarks. As a proper way of handling relativistic effects, the lightfront quark model (LFQM) [4–8] appears to be one of the most efficient and effective tools in hadron physics as it takes advantage of the distinguished features of the lightfront dynamics (LFD) [9, 10]. In particular, the LFD carries the maximum number (seven) of the kinetic (or interaction independent) generators and thus the less effort in dynamics is necessary in order to get the QCD solutions that reflect the full Poincare´ symmetries. Moreover, the rational energy-momentum dispersion relation of LFD, namely p− = (p2⊥ + m2 )/p+ , yields the sign correlation between the light-front (LF) energy p− (= p0 − p3 ) and the LF longitudinal momentum p+ (= p0 + p3 ) and leads to the suppression of quantum fluctuations of the vacuum, sweeping the complicated vacuum fluctuations into the zero-modes in the limit of p+ → 0 [11–13]. This simplification is a remarkable advantage in LFD and facilitates the partonic interpretation of the amplitudes. Based on the advantages of the LFD, the LFQM has been developed [14] and subsequently applied for various meson phenomenologies such as the mass spectra of both heavy and light mesons [15], the decay constants, distribution amplitudes, form factors and generalized parton distributions [10, 14–23]. Despite these successes in reproducing the general features of the data, however, it has proved very difficult to obtain direct connection between the LFQM and QCD. Typically, rigorous derivations of the connection between the Angular asymmetries as a probe for anomalous contributions to HZZ vertex at the LHC N. Belyaev National Research Nuclear University (Moscow Engineering Physics Institute), 31 Kashirskoe Shosse, Moscow 115409, Russia R. Konoplich Department of Physics, New York University, 4 Washington Place, New York, NY 10003, USA∗ L. Egholm Pedersen Niels Bohr Institute, University of Copenhagen, Blegdamsvej 17 Kobenhavn, Denmark arXiv:1502.03045v1 [hep-ph] 10 Feb 2015 K. Prokofiev Department of Physics, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon, Hong Kong† (Dated: February 11, 2015) In this article, the prospects for studying the tensor structure of the HZZ vertex with the LHC experiments are presented. The structure of tensor couplings in Higgs di-boson decays is investigated by measuring the asymmetries and by studing the shapes of the final state angular distributions. The expected background contributions, detector resolution, and trigger and selection efficiencies are taken into account. The potential of the LHC experiments to discover sizeable non-Standard Model contributions to the HZZ vertex with 300 fb−1 and 3000 fb−1 is demonstrated. I. INTRODUCTION In the Summer of 2012, the CMS and ATLAS Collaborations at the LHC reported the discovery of a new neutral resonance in searches for the Standard Model Higgs boson. This discovery was later confirmed by analyses of the full LHC Run-I dataset by both collaborations [1, 2]. It was demonstrated that the new particle with a mass around 125.5 GeV was dominantly produced via the gluon-fusion process and decays into pairs of gauge bosons: γγ, ZZ and W W . The observed production and decay modes identified the discovered particle as a neutral boson. The subsequent measurement of its couplings to fermions and bosons demonstrated the compatibility of the discovered resonance with the expectations for the Standard Model Higgs boson within available statistics [3–5]. In the Standard Model, electroweak symmetry breaking via the Higgs mechanism requires the presence of a single neutral Higgs boson with spin 0 and even CPparity. Theories beyond the Standard Model often require an extended Higgs sector featuring several neutral Higgs bosons of both even and odd CP-parity. In such a case, mixing between Higgs boson CP-eigenstates is possible. The Higgs boson mass eigenstates observed in experiment may thus have mixed CP-parity. Such an extension of the Higgs sector is important because effects of CP violation in the SM are too small and, in particular, cannot explain the baryon asymmetry of the Universe. Dedicated studies of spin and parity of the Higgs candidate discovered by ATLAS and CMS showed that its dominant spin and parity are compatible with J CP = 0++ [4–6]. The dataset of about 25 fb−1 currently collected by each of the major LHC experiments allows to set an upper limit on the possible CP-odd contribution. The sensitivity is expected to improve with larger datasets to be collected at the LHC. There have been many works on direct measurement of CP violation in the Higgs sector [7–29]. In this paper the sensitivity of LHC experiments to observe CP-mixing effects with 300 fb−1 and 3000 fb−1 is evaluated using the method of angular asymmetries. This paper is organised as follows. In Section II observables sensitive to CP violation in the HZZ vertex are discussed. The spin-0 model, a Monte Carlo production of signal and background, and a lagrangian parametrisation for CP-mixing measurements are discussed in Section III. In Section IV the expected sensitivity of the LHC experiments to the CP-violation effects based on angular asymmetries is presented. Constraits are set on the contribution of anomalous couplings to the HZZ vertex. Section V introduces the measurement technique based on observables fit. Exclusion regions for the mixing angle are presented. Section VI gives the overall summary of obtained results. II. OBSERVABLES In this paper we study the sensitivity of final state observables to the CP violating HZZ vertex in the process: ∗ † Also at Physics Department, Manhattan College, 4513 Manhattan College Parkway, Riverdale, New York, NY 10471, USA. Also at Institute for Advanced Study, HKUST, Clear Water Bay, Kowloon, Hong Kong. gg → H → ZZ → 4l. (1) Following the notation introduced in [21], the general CFTP/15-01 arXiv:1502.03008v1 [hep-ph] 10 Feb 2015 New texture-zero models for lepton mixing L. Lavoura∗ CFTP, Instituto Superior T´ecnico, Universidade de Lisboa Avenida Rovisco Pais 1, 1049-001 Lisboa, Portugal 10 February 2015 Abstract I systematically consider, in the context of the type-I see-saw mechanism, all the predictive cases in which both the Dirac mass matrix connecting the left-handed neutrinos to the right-handed neutrinos, and the Majorana mass matrix of the latter neutrinos, feature texture zeros, while the mass matrix of the charged leptons is diagonal. I have found a few cases which had not been discussed in the literature previously. 1 Introduction There has recently been renewed interest in the possibility of ‘texture’ zeros in the fermion mass matrices [1, 2, 3]. Texture zeros are well grounded in renormalizable field theories, since they can always be implemented through models with suitable Abelian symmetries and (possibly many) scalar fields with vacuum expectation values [4]. The revival of interest was partially motivated by the realization of the fact that a popular alternative approach, where lepton mixing is completely determined by a non-Abelian symmetry, seems to have been fully explored [5]. With three Majorana neutrinos, the mass Lagrangian is Lmass = −ℓ¯L Mℓ ℓR − ℓ¯R Mℓ† ℓL + ∗ 1 T −1 ν C Mν − ν¯M ∗ C ν¯T , 2 E-mail: [email protected] 1 (1) Prepared for submission to JHEP FERMILAB-PUB-15-030-T arXiv:1502.02990v1 [hep-ph] 10 Feb 2015 Higgs constraints from vector boson fusion and scattering John M. Campbell and R. Keith Ellis Fermilab, PO Box 500, Batavia, IL 60510, USA E-mail: [email protected], [email protected] Abstract: We present results on 4-lepton + 2-jet production, the partonic processes most commonly described as vector boson pair production in the Vector Boson Fusion (VBF) mode. This final state contains diagrams that are mediated by Higgs boson exchange. We focus particularly on the high-mass behaviour of the Higgs boson mediated diagrams, which unlike on-shell production, gives information about the Higgs couplings without assumptions on the Higgs boson total width. We assess the sensitivity of the high-mass region to Higgs coupling strengths, considering all vector boson pair channels, W − W + , W ± W ± , W ± Z and ZZ. Because of the small background, the most promising mode is W + W + which has sensitivity to Higgs couplings because of Higgs boson exchange in the t-channel. Using the Caola-Melnikov (CM) method, the off-shell couplings can be interpreted as bounds on the Higgs boson total width. We estimate the bound that can be obtained with current data, √ as well as the bounds that could be obtained at s = 13 TeV in the VBF channel for data samples of 100 and 300 fb−1 . The CM method has already been successfully applied in the gluon fusion (GGF) production channel. The VBF production channel gives important complementary information, because both production and decay of the Higgs boson occur already at tree graph level. arXiv:1502.02986v1 [hep-ph] 10 Feb 2015 Kinematic biases on centrality selection of jet events in pPb collisions at the LHC N´estor Armesto Departamento de F´ısica de Part´ıculas and IGFAE, Universidade de Santiago de Compostela, E-15706 Santiago de Compostela, Galicia-Spain Do˘ ga Can G¨ ulhan Laboratory for Nuclear Science and Department of Physics, Massachusetts Institute of Technology (MIT), Cambridge, MA 02139 USA Jos´e Guilherme Milhano CENTRA, Instituto Superior T´ ecnico, Universidade de Lisboa, Av. Rovisco Pais, P-1049-001 Lisboa, Portugal and Physics Department, Theory Unit, CERN, CH-1211 Gen` eve 23, Switzerland Abstract Centrality selection has been observed to have a large effect on jet observables in pPb collisions at the Large Hadron Collider, stronger than that predicted by the nuclear modification of parton densities. We study to which extent simple considerations of energy-momentum conservation between the hard process and the underlying event affect jets observables in such collisions. We develop a simplistic approach that considers first the production of jets in a pp collision as described by PYTHIA. From each pp collision, the value of the energy of the parton from the proton participating in the hard scattering is extracted. Then, the underlying event is generated simulating a pPb collision through HIJING, but with the energy of the proton decreased according to the value extracted in the previous step, and both collisions are superimposed. This model is able to capture the bulk of the centrality effect for central to semicentral collisions, for the two available sets of data: dijets from the CMS Collaboration and single jets from the ATLAS Collaboration. As expected, the model fails for peripheral collisions where very few nucleons from Pb participate. ∗ Preprint number: CERN-PH-TH-2015-021. Email addresses: [email protected] (N´ estor Armesto), [email protected] (Do˘ ga Can G¨ ulhan), [email protected] (Jos´ e Guilherme Milhano) Preprint submitted to Elsevier February 11, 2015 Hunting for the Xb via hidden bottomonium decays Gang Li,1,2∗ and Zhu Zhou1† 1 2 Department of Physics, Qufu Normal University, Qufu 273165, China State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing 100190, China (Dated: February 11, 2015) arXiv:1502.02936v1 [hep-ph] 10 Feb 2015 In this work, we study the isospin conserved hidden bottomonium decay of Xb → Υ(1S)ω, where Xb is taken to be the counterpart of the famous X(3872) in the bottomonium sector as a candidate ¯ ∗ threshold and the mass for the meson-meson molecule. Since it is likely that the Xb is below the B B difference between the neutral and charged bottom meson is small compared to the binding energy of the Xb , the isospin violating decay mode Xb → Υ(nS)π + π − would be greatly suppressed. We use the effective Lagrangian based on the heavy quark symmetry to explore the rescattering mechanism of Xb → Υ(1S)ω and calculate the partial widths. Our results show that the partial width for the Xb → Υ(1S)ω is about tens of keVs. Taking into account the fact that the total width of Xb may be smaller than a few MeV like X(3872), the calculated branching ratios may reach to orders of 10−2 . These hidden bottomonium decay modes are of great importance in the experimental search for the Xb particularly at the hadron collider. Also, the associated studies of hidden bottomonium ¯ may help us investigate the structure of Xb deeply. The decays Xb → Υ(nS)γ, Υ(nS)ω, and B Bγ experimental observation of Xb will provide us with further insight into the spectroscopy of exotic states and is helpful to probe the structure of the states connected by the heavy quark symmetry. PACS numbers: 13.25.Hw, 13.75.Lb, 14.40.Pq I. INTRODUCTION During recent years, the experimental observation of a large number of so-called XY Z states has inspired tremendous effort to unravel their nature beyond the conventional quark model [1–7]. In 2003, the Belle Collaboration first reported the observation of X(3872) in the J/ψπ + π − invariant mass spectrum of B + → K + + J/ψπ + π − [8] which was subsequently confirmed by the BaBar Collaboration [9] in the same channel. It was also discovered in protonproton/antiproton collisions by the D0 [10], CDF [11], and LHCb Collaborations [12, 13]. The X(3872) is the first, and perhaps the most renowned exotic candidate; however, its nature is still ambiguous due to its peculiar properties. First, only an upper bound of the total width has been measured experimentally: Γ < 1.2 MeV [14], which is tiny compared to typical hadronic widths. Second, the mass is located close to the D0 D ∗0 threshold, MX(3872) − MD0 − MD∗0 = (−0.12 ± 0.24) MeV [15], which leads to speculation that the X(3872) is presumably a meson-meson molecular state [16, 17]. Many studies on the production and decay of the X(3872) have been carried out in order to understand its nature. The discrimination of a compact multiquark configuration and a loosely bound hadronic molecule configuration is one important aspect. From this point, it is also valuable to look for the counterpart in the bottom sector, denoted as Xb following the notation in Ref. [18], as states related by heavy quark symmetry may have universal behaviors. Since ∗ † [email protected] [email protected] ¯0 → K ¯ ∗0 X(Y Z) and B ¯ 0 → φX(Y Z) with X(4160), Y (3940), Z(3930) Predictions for the B s Wei-Hong Liang,1, 2 Ju-Jun Xie,2, 3, 4 and E. Oset2, 5 1 Department of Physics, Guangxi Normal University, Guilin 541004, China Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000, China 3 Research Center for Hadron and CSR Physics, Institute of Modern Physics of CAS and Lanzhou University, Lanzhou 730000, China 4 State Key Laboratory of Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing 100190, China 5 Departamento de F´ısica Te´ orica and IFIC, Centro Mixto Universidad de Valencia-CSIC Institutos de Investigaci´ on de Paterna, Aptdo. 22085, 46071 Valencia, Spain (Dated: February 11, 2015) arXiv:1502.02932v1 [hep-ph] 10 Feb 2015 2 ¯0 → K ¯ ∗0 R and B ¯s0 → φR with R being the X(4160), Y (3940), We investigate the decay of B Z(3930) resonances. Under the assumption that these states are dynamically generated from the vector-vector interaction, as has been concluded from several theoretical studies, we use a reaction mechanism of quark production at the elementary level, followed by hadronization of one final q q¯ pair into two vectors and posterior final state interaction of this pair of vector mesons to produce the resonances. With this procedure we are able to predict five ratios for these decays, which are closely linked to the dynamical nature of these states, and also predict the order of magnitude of the branching ratios which we find of the order of 10−4 , well within the present measurable range. The measurement of these decays rates can help unravel the nature of these resonances. PACS numbers: I. INTRODUCTION The XY Z resonances with masses in the region around 4000 MeV have stirred the hadron community with a series of states that challenge the common wisdom of mesons as made from q q¯. There has been intense experimental work done at the BABAR, BELLE, CLEO, BES and other collaborations, and many hopes are pinned in the role that the future FAIR facility with the PANDA collaboration and J-PARC will play in this field. There are early experimental reviews on the topic [1–4] and more recent ones [5–9]. From the theoretical point of view there has been also an intensive activity trying to understand these intriguing states. There are quark model pictures [10, 11] and explicit tetraquark structures [12]. Molecular interpretations are given in refs. [13–21]. Much progress also has been done using the heavy quark spin symmetry (HQSS) [22, 23]. Predictions using QCD sum rules have also brought some light into the issue [24–26]. Strong decays of these resonances have been studied to learn about the nature of these states [27, 28], while very often radiative decays are invoked as a tool to provide insight into this problem [29–33], although there might be exceptions as discussed in ref. [34]. It has even been speculated that some states found near thresholds of two mesons could just be cusps, or threshold effects [35, 36]. Some theoretical reports on these issues can be found in refs. [37–39]. On the other hand, and somewhat unexpected, recent experiments on the weak decays of B meson are proving to be a powerful source of information on hadron dynamics and the nature of hadronic states [40–45]. One of the recent surprises was to see from these experiments a pronounced peak for the f0 (980) in Bs0 decay into J/ψ and π + π − [40] while the signal for the f0 (500) was found very small or non-existent. Simultaneously, in the analogous ¯ 0 into J/ψ and π + π − [44] a signal was seen for decay of B the f0 (500) production and only a very small fraction was observed for the f0 (980) production. This is surprising since the f0 (500) couples more strongly to π + π − than to the f0 (980). Some attempts to explain this behaviour was offered in ref. [46] in terms of tetraquark structures for the scalar mesons. Furthermore, the f0 (500) and f0 (980) resonances are naturally explained as states dynamically generated from the meson-meson interaction in chiral unitary theory [47–52]. From this perspective the features observed in these experiments and different ratios were well described in ref. [53]. The basic approach in ref. [53] was to identify the dominant mechanism of the decays at the quark level, implementing the hadronization of the final q q¯ pair into two mesons and allowing them to interact to generate the f0 (500) and f0 (980) resonances. The picture of ref. [53] has been extended to describe many other B and D decays, with equal success in the description of observed features of the reactions. In ref. [54] ratios for the production of vector mesons in the final states were evaluated and predictions for the ¯s0 → J/ψκ(800) decay were made. In ref. [55] the B D0 decays into Ks0 and f0 (500), f0 (980), a0 (980) were studied. A different sort of states, dynamically generated from the vector-vector interaction were investigated ¯ 0 and B ¯s0 decays into J/ψ and in ref. [56] in the B f0 (1370), f0 (1710), f2 (1270), f2′ (1525), K2∗ (1430). In ¯ 0 decay into D0 and ρ or f0 (500), f0 (980), ref. [57] the B ¯ 0 decay into D0 and K ∗0 or κ(800) were a0 (980) and B s studied. Similarly, the Bs0 decay into Ds DK was studied with the aim of learning about KD scattering and the ∗ Ds0 (2317) resonance [58]. Related work to this latter one arXiv:1502.02931v1 [hep-ph] 10 Feb 2015 Search for Charged Higgs bosons via decays to W ± and a 125 GeV Higgs at the Large Hadron Collider Rikard Enberga , William Klemm∗a , Stefano Morettib , Shoaib Munira and Glenn Woudaa a Department of Physics and Astronomy, Uppsala University Box 516 , SE-Uppsala, Sweden of Physics & Astronomy, University of Southampton, Highfield, Southampton SO17 1BJ, UK E-mail: [email protected], [email protected], [email protected], [email protected], [email protected] b School The recent observation of a 125 GeV neutral Higgs boson (Hobs ) provides additional input for charged Higgs boson searches in the H ± → W ± Hobs decay channel at the Large Hadron Collider (LHC). We reassess the discovery potential in this channel, which is important for H ± heavier than the top quark mass. When Hobs decays to a bb¯ pair, knowledge of the Higgs mass aids in the kinematic selection of signal events. We perform a signal-to-background analysis to demonstrate the LHC prospects for charged Higgs discovery in the resulting channel ¯ − → `± ν` j jbbb( ¯ b)+h.c. ¯ pp → t(b)H for standard (300 fb−1 ) and high (3000 fb−1 ) luminosities √ at design energy, s = 14 TeV. We find that regions of the parameter space of several two-Higgs doublet models, consistent with constraints from LHC Higgs searches and b-physics observables, are testable in this channel. Prospects for Charged Higgs Discovery at Colliders 16-18 September 2014 Uppsala University Sweden ∗ Speaker. c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence. Search for H ± → W ± Hobs at the LHC http://pos.sissa.it/ William Klemm 1. Introduction The observation of a Higgs boson (Hobs ) [1] at the Large Hadron Collider (LHC) may be just the first glimpse into the rich phenomenology of a larger Higgs sector. Indeed, many models require additional Higgs states, including charged Higgs bosons (H ± ), the observation of which would be a clear sign of physics beyond the standard model (SM). Experimental searches for H ± have largely focused on decays to tb or τν, which dominate much of the parameter space of many models. However, when kinematically allowed, the decay H ± → W ± Hobs can become significant for many parameter configurations. Earlier studies [2] demonstrated the potential of this channel, and the newfound knowledge of the Higgs mass, mHobs ≈ 125 GeV, provides an additional input for the analysis and a constraint on extensions of the Higgs sector (see also [3] for a recent discussion). Here we describe a collider analysis for the H ± → W ± Hobs channel and determine its sensitivity at the LHC, which we compare to the possible signal strengths of several two Higgs doublet models (2HDMs) compatible with current experimental observations. 2. Collider Analysis The main production channel at the LHC for a charged Higgs above the top mass is typically pp → t(b)H ± ,1 which is possible through the coupling of the charged Higgs to third generation ¯ quarks. Focusing then on H ± → HobsW ± decays, we consider the subsequent decay Hobs → bb, as both b-quarks are observable, allowing us to directly reconstruct the observed 125 GeVstate, and because SM-like Higgs bosons in this mass range decay dominantly in this channel.2 The process we then wish to search for is pp → (b)tH ± → (b)bW ∓W ± Hobs → (b)bbb j j`ν` , where one of the W -bosons (from either H ± or top decay) decays leptonically and the other hadronically. The presence of a single lepton allows us to avoid multi-jet backgrounds, while requiring one hadronic W avoids additional unseen neutrinos, making the event reconstruction more straightforward. The ¯ where either an additional b-tagged jet combines with main background for this process is t t¯b(b), a b-jet from a top decay or an additional bb¯ pair mimics an Hobs → bb¯ decay. To get a measure of the sensitivity that could be obtained at the 14 TeV LHC, we generate the t(b)H ± signal using Pythia 6.4.28 [4] with the MATCHIG [5] add-on to avoid double counting among bg → tH ± and gg → tbH ± processes, and all t(b)W X, X → bb¯ backgrounds with MadGraph5 [6]. Both signal and background undergo parton showering and hadronization using Pythia 8 [7] and are further processed with the DELPHES 3 [8] detector simulation using experimental parameters based on the ATLAS experiment with modified b-tagging efficiencies.3 To reconstruct our signal events and reduce background, we use the following procedure, inspired by previous studies [2], with an additional top veto: 1 This should be interpreted as pp → t(b)H ¯ − + pp → t¯(b)H + . Throughout this text, we will not distinguish fermions and anti-fermions when their identity is unspecified and/or can be inferred. 2 In principle, other decay channels could also be competitive. It has been suggested that, especially in analyses dominated by systematic errors, the Hobs → τ + τ − channel could be useful despite additional missing energy from τ decays and a reduced branching ratio, largely as a result of lower backgrounds [3]. 3 The b-tagging efficiency chosen is ε tanh(0.03p − 0.4), with ε = 0.7 for central (|η| ≤ 1.2) and ε = 0.6 for η η η T forward (1.2 ≤ |η| ≤ 2.5) jets, and the transverse momentum, pT , in GeV. This is a conservative choice compared with high-luminosity projections. 2 arXiv:1502.02857v1 [hep-ph] 10 Feb 2015 Photon emission rates near the critical point in the linear sigma model F. Wunderlich Helmholtz-Zentrum Dresden-Rossendorf, Institute of Radiation Physics, Bautzner Landstr. 400, D-01328 Dresden, Germany and Institut für Theoretische Physik, Technsche Universität Dresden, D-01062 Dresden, Germany E-mail: [email protected] B. Kämpfer∗ Helmholtz-Zentrum Dresden-Rossendorf, Institute of Radiation Physics, Bautzner Landstr. 400, D-01328 Dresden, Germany and Institut für Theoretische Physik, Technsche Universität Dresden, D-01062 Dresden, Germany E-mail: [email protected] Employing the linear sigma model, the effective masses of quasi-particle excitations are found to exhibit significant variations within the phase diagram, which has a critical point at non-zero chemical potential, where a first-order phase transition sets in. Soft-photon emission rates in lowest order display, for selected channels, a sensible dependence on the effective masses of the involved excitations and let us argue that they could map out the phase diagram. 9th International Workshop on Critical Point and Onset of Deconfinement - CPOD2014, 17-21 November 2014 ZiF (Center of Interdisciplinary Research), University of Bielefeld, Germany ∗ Speaker. c Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence. Photon emission rates near the critical point in the linear sigma model http://pos.sissa.it/ B. Kämpfer 1. Introduction Confinement and spontaneous symmetry breaking as well as their respective counterparts - deconfinement and chiral restoration - are central issues of QCD. Their mutual relationship is among the main questions investigated in heavy ion collisions (HICs). A particularly challenging task is the establishment of the QCD phase diagram in a region of temperature T and baryo-chemical potential µ which is accessible in HICs. While the beam energy scan at RHIC and forthcoming accelerator/detector installations, e.g. at FAIR/CBM and NICA/MPD, aim at finding signatures of the onset of deconfinement as a first-order phase transition in a critical point (CP), QCD based [1,2] and QCD rooted [3] calculations try to quantify its coordinates. Instead of facing the sign problem of QCD at non-zero baryon density, one can resort to suitable models which display a CP at (TCP , µCP ) > (0, 0) and a line of first-order phase transitions for µ > µCP (cf. [4, 5] for recent surveys). By universality arguments, one can elucidate observables signaling the CP. In the previous search for deconfinement effects in HICs, electromagnetic probes (cf. [6–8] for recent evaluations and further references) have been considered as promising since, by their penetrating nature, they monitor the full space-time evolution of matter in the course of HICs. Given the proximity of deconfinement and chiral restoration at µ /T ≪ 1, the dilepton spectra have been considered in [9, 10] as candidates for messengers of chiral restoration. It appeared that at the pseudocritical temperature of Tpc ∼ 154 MeV the dilepton emission rates of confined matter (hadrons) and deconfined matter (quarks and gluons) become degenerate - quite natural since Tpc quantifies the cross over location at µ /T ≪ 1. This degeneracy can be named quark-hadron duality and has been employed [11–13] to verify a “thermal radiation” component besides hard initial yield and electromagnetic hadron final-state decays after the disassembly of the fireball in HICs. The approximate degeneracy of real-photon emission rates of confined and deconfined matter has been pointed out quite early [14] and can be used analogously to arrive at a consistent modeling of thermal radiation in HICs, either schematically [15, 16] or with many refinements [17–19]. The recent analysis in [17, 20], however, revealed that the calculated photon spectra fall short in comparison with data. The tension is caused, to some extent, by the consistency requirement of photon-v2 and photon-p⊥ systematics. According to [17,18], a solution is offered by the hypothesis of a “pseudo-critical enhancement” of the photon emission at Tpc ± ∆T with ∆T = O(15 MeV). It is therefore tempting to look for arguments which could support the hypothesis launched there and, more general, to extend the consideration over the QCD phase diagram and to check whether the CP can have a distinguished impact on the photon emission rate. 2. Linear σ model We utilize here the linear sigma model (Lσ M), which has been originally designed to model spontaneous chiral symmetry breaking [21] and has been later coupled to the fermionic sector. It is a special quark-meson model with the Lagrangian LLσ M = L∂ ψ + Lψ M + L∂ M + LM + Ls.b. , where the kinetic terms L∂ ψ and L∂ M are supplemented by the O(4) symmetric meson self-interaction LM , which refers to an SU (2)L × SU (2)R symmetry which, in combination with the symmetry breaker Ls.b. = H σ , dynamically generates mass terms; the fermion-meson coupling of Yukawa type is encoded in Lψ M . The field content of L is a two component Fermion (light quark doublet 2 The signatures of the quintuplet leptons at the LHC You Yu 1 , Chong-Xing Yue 1 ,∗ and Shuo Yang 1 Department of Physics, Liaoning Normal University, Dalian 116029, China 2 arXiv:1502.02801v1 [hep-ph] 10 Feb 2015 2† Physics Department, Dalian University, Dalian, 116622, China Abstract We investigate production and detection prospects of the quintuplet heavy leptons at the LHC in the context of a new model which is proposed as a viable and testable solution to the neutrino masses problem. We classify the signals that the heavy leptons produce in terms of the charged lepton multiplicity. The 2l± l∓ 2j/ ET and 2l± 2l∓ 2j signals are mainly studied that we carry out a full simulation in this paper. After applying suitable kinematic cuts, the background events are substantially suppressed. We also study the 3l± l∓ 2j, 3l± l∓ /ET and 3l± 3l∓ signals. The production rate of the 3l± 3l∓ signal is much small, while other signatures of the heavy leptons might be detected at the 14TeV LHC. PACS numbers: 14.60.Hi, 14.60.Pq, 13.85.Qk ∗ Electronic address: [email protected] † Electronic address: [email protected] 1 Flavor dependence of normalization constant for an infrared renormalon Taekoon Lee∗ Department of Physics, Kunsan National University, Kunsan 573-701, Korea arXiv:1502.02698v1 [hep-ph] 9 Feb 2015 An ansatz is proposed for the flavor dependence of the normalization constant for the first IR renormalon in heavy quark pole mass. The ultraviolet (UV) and infrared (IR) renormalons in field theory are fascinating objects that give rise to factorially growing large order behavior in perturbation theory. In quantum chromodynamics (QCD) the IR renormalons can be understood within the framework of operator product expansion (OPE) [1–6]. An IR renormalon in a Wilson coefficient in the OPE causes ambiguity in the resummed asymptotic series of the Wilson coefficient, which is to be cancelled by the vacuum condensate of an higher dimensional operator. This cancellation of the ambiguities in the resummation and vacuum condensate determines the nature of the renormalon singularities in the Borel plane. Specifically, the functional form of the condensate in the strong coupling αs , which can be determined up to an overall constant by renormalization group (RG) equation, determines the power of singularity as well as its location [7]. However, the residue of the singularity, which is the normalization constant of the renormalon-caused large order behavior, is not known, but it can be calculated by a perturbation method [8, 9]. While the normalization can be expressed in a convergent series, with finite order perturbation it can only be calculated approximately. Its exact form is a nonperturbative quantity and so far there is no known way to calculate it. It would thus be very interesting if we somehow find the exact form for the normalization. Our purpose in this Letter is to present an ansatz for the normalization for the first IR renormalon in the heavy quark pole mass. In this case the perturbation method for the normalization yields a series that converges rather quickly, which allows to determine the normalization within a few percent of uncertainty using the known first three perturbative coefficients [10, 11]. The reason for this rapid convergence and accuracy may lie with following two facts. 2 First, the renormalon singularity is relatively soft, with its singularity of (1 − 2b)−(1+β1 /2β0 ) , for example, compared 2 to that of the first IR renormalon in Adler function, which is of (1 − b/2)−(1+2β1 /β0 ) , where β0 , β1 are the first two coefficients of the beta function and b is the complex variable for the Borel plane. With vanishing flavor number Nf = 0, for example, the singularities are (1 − 2b)−1.42 and (1 − b/2)−2.69 , respectively. Secondly, the IR renormalon is the closest singularity to the origin in the Borel plane. This condition is important because the normalization in the perturbation method is evaluated on the boundary of convergence disk and for that to work the singularity should be closer to the origin than any other singularities. Of course, any renormalon singularity can be moved by a conformal mapping to be the closest one to the origin, this step is not required with the first IR renormalon for the pole mass, because it is already the closest one, and this seems to help the convergence. The normalization constant obtained from perturbation method was confirmed by recent lattice calculation of large order behaviour of static energy [12, 13]. To get the ansatz let us assume that the condensate in the OPE is of dimension n and is proportional to n − ΛnQCD ∼ e− 2β0 αs α nβ1 2β 2 0 (1 + O(αs )) (1) and the associated renormalon singularity is of the form: N . (1 − b/b0 )1+ν (2) Then the imaginary part, which is ambiguous, of the Borel integral Z ∞ 1 N Im db = ±N sin(νπ)Γ(−ν)(b0 /β0 )1+ν e−b0 /β0 αs α−ν e−b/β0 αs s (1 + O(αs )) β0 0 (1 − b/b0 )1+ν (3) is to be cancelled by ambiguity of the form (1). Thus identifying (3) with (1) we get b0 = n/2 , ν = nβ1 /2β02 , N = C( 2βn0 )ν , sin(νπ)Γ(−ν) (4) where C is an unknown proportionality constant. Now putting C = C0 f (ν) ∗ (5) [email protected] 2 Nf 0 1 2 3 4 5 Npert. 0.6081 0.5981 0.5867 0.5730 0.5551 0.5288 N /Npert. 1.0047 0.9979 0.9973 1.0081 1.0403 1.116 TABLE I. Comparison of the ansatz (9) with normalization from perturbation method for varying number of flavors. with f (0) = 1, where C0 is determined so that the normalization agrees with that from the large-β0 approximation at ν = 0, we get N = C0 f (ν)( 2βn0 )ν . sin(νπ)Γ(−ν) (6) We shall now consider the normalization for the pole mass, for which n = 1. While in this case the ambiguity in Borel summation is not canceled by a condensate of dimension one operator but by the static inter-quark potential [14], the ambiguity is nevertheless of the form (1) and the relations (4) are still valid. For this case the large-β0 approximation fixes C0 in the MS scheme as [15–17] C0 = −CF e5/6 , (7) where CF = 4/3 for QCD. Of course f (ν) is not known, and we can only guess it by comparing the normalization with values from the perturbation method. This gives f (ν) = 4−ν (8) and, finally, CF e 6 ( β20 )ν , sin(νπ)Γ(−ν) 5 N =− (9) β1 /2β02 . This is our proposed ansatz. for the MS scheme, where ν = How well does this ansatz work? Table I compares the ansatz with the normalization from the perturbative method for varying number of flavors, the details of which will be discussed shortly. The agreement is quite impressive for up to Nf = 4. It is to be noted that the perturbative method tend to work better for smaller Nf . Of course, this does not mean that the ansatz is necessarily correct. One test may be to expand (9) for small ν and compare it with subleading corrections in large-β0 approximation, for which only partial result exists [18]. Expanding (9) at ν = 0, we have N = CF e5/6 [1 + (γE + log(β0 /2))ν + O(ν 2 )] . π (10) The Euler constant term agrees with the corresponding term in [18]. It is worth noting that the two transcendental numbers π and γE in (10) both arise from sin(νπ)Γ(−ν) (11) in the denominator in (9). This is a strong indication that the term should be, at least, part of the exact form for the normalization. It may be tempting to use the same idea to make an ansatz for other renormalons, for example, such as the first IR renormalon in the Adler function, which is associated with the gluon condensate, for which n = 4. However, there is no accurate estimate of the normalization for the Adler function; The convergence from the perturbative method is not fast [19]. Without accurate numerical estimates for the normalization it is impossible to infer f (ν) for the Adler function and that blocks such an attempt. Nevertheless, if we assume (8) is applicable to the Adler function as well, then we have an ansatz for the first IR renormalon of the Adler function 3 CF e 3 ( β80 )ν N =−4 , sin(νπ)Γ(−ν) 10 (12) where ν = 2β1 /β02 , and the following large-β0 result is used [17, 20, 21]: C0 = 10 3 CF e 3 . 4 (13) arXiv:1502.02682v1 [hep-ph] 9 Feb 2015 Non-conventional mesons at PANDA Francesco Giacosa Abstract. Non-conventional mesons, such as glueballs and tetraquarks, will be in the focus of the PANDA experiment at the FAIR facility. In this lecture we recall the basic properties of QCD and describe some features of unconventional states. We focus on the search of the not-yet discovered glueballs and the use of the extended Linear Sigma Model for this purpose, and on the already discovered but not-yet understood X, Y, Z states. Institute of Physics, Jan Kochanowski University, 25-406 Kielce, Poland and Institute for Theoretical Physics, J. W. Goethe University, Max-von-Laue-Str. 1, 60438 Frankfurt am Main, Germany 1. Introduction Conventional mesons are bound states made by a quark and an antiquark. Yet, since the very beginning of QCD the search for other possibilities has attracted the attention of both experimentalists and theoreticians [1]. As a prominent example, glueballs were predicted long ago: they are (yet hypothetical) bound states of solely gluons. Computer simulations of QCD on the lattice have found a full spectrum of these states [2, 3], but their firm experimental discovery has not yet taken place. On the other hand, a plenty of mesons, denoted as X, Y, and Z states, has been unambiguously discovered in the last decade in the energy region of charm-anticharm and botton-antibotton states [4, 5]. A clear explanation about the nature of these states is still lacking (tetraquark and molecular hypotheses are a possibility). The PANDA experiment at the FAIR facility [6] in Darmstadt/Germany is designed to shed light on these questions. It is a proton-antiproton scattering experiment in which the energy of the antiproton can be finely tuned in such a way that a wide energy range in the charmonium region can be scanned. Various resonances can be directly formed in proton-antiproton fusion processes. Glueball, if existent, shall be found by this experiment. On the other hand, many of the X, Y, and Z states can also be formed and/or produced with high statistics. In this lecture a theoretical view concerning the search of non-conventional mesons at PANDA will be presented. 2. Brief recall of the QCD Lagrangian and its symmetries The Lagrangian of Quantum Chromodynamics (QCD) reads LQCD = Nf X i=1 1 q i (iγ µ Dµ − mi )qi − Gaµν Ga,µν , Dµ = ∂µ − ig0 Aµ 4 (1) where Gaµν = ∂µ Aaν − ∂ν Aaµ + g0 f abc Abµ Acν , Aµ = Aaµ ta , a, = 1, ..., Nc2 − 1 = 8, and ta and f abc are the generators and the structure constants of the group SU (Nc ). LQCD contains Nf quark CUMQ/HEP 188 Dark Matter in the Higgs Triplet Model Sahar Bahrami1a and Mariana Frank1b 1 Department of Physics, Concordia University, 7141 Sherbrooke St. West , Montreal, Quebec, Canada H4B 1R6. (Dated: February 11, 2015) arXiv:1502.02680v1 [hep-ph] 9 Feb 2015 Abstract The inability to predict neutrino masses and the existence of the dark matter are two essential shortcomings of the Standard Model. The Higgs Triplet Model provides an elegant resolution of neutrino masses via the seesaw mechanism. We show here that introducing vectorlike leptons in the model also provides a resolution to the problem of dark matter. We investigate constraints, including the invisible decay width of the Higgs boson and the electroweak precision variables, and impose restrictions on model parameters. We analyze the effect of the relic density constraint on the mass and Yukawa coupling of dark matter. We also calculate the cross sections for indirect and direct dark matter detection and show our model predictions for the neutrino and muon fluxes from the Sun, and the restrictions they impose on the parameter space. With the addition of vectorlike leptons, the model is completely consistent with dark matter constraints, in addition to improving electroweak precision and doubly charged mass restrictions, which are rendered consistent with present experimental data. PACS numbers: 14.80.Fd, 12.60.Fr, 14.60.Pq Keywords: LHC phenomenology, Higgs Triplet Model a Email: [email protected] b Email: [email protected] 1 Generically large nongaussianity in small multifield inflation Joseph Bramante Department of Physics University of Notre Dame Notre Dame, IN, 46556, USA arXiv:1502.02674v1 [hep-ph] 9 Feb 2015 If forthcoming measurements of cosmic photon polarization restrict the primordial tensor-to-scalar ratio to r < 0.01, small field inflation will be a principal candidate for the origin of the universe. Here we show that small multifield inflation, without the hybrid mechanism, typically results in large squeezed nongaussianity. Small multifield potentials contain multiple flat field directions, often identified with the gauge invariant field directions in supersymmetric potentials. We find that unless these field directions have equal slopes, large nongaussianity arises. After identifying relevant differences between large and small two-field potentials, we demonstrate that the latter naturally fulfill the Byrnes-Choi-Hall large nongaussianity conditions. Computations of the primordial power spectrum, spectral index, and squeezed bispectrum, reveal that small two-field models which otherwise match observed primordial perturbations, produce excludably large nongaussianity if the inflatons’ field directions have unequal slopes. 2 I. INTRODUCTION Learning what forms of cosmological inflation are favored by observation deepens our understanding of the universe’s origin and structure. This paper shows that if inflation is sourced by multiple scalar fields traversing sub-Planckian field ranges, the Planck Collabsq oration’s bound on squeezed (aka local) nongaussianity, fNL = 2.5 ± 5.7 [1], often implies a certain structure for small multifield potentials; without this structure they generically 1 produce large squeezed nongaussianity. This has implications for the couplings of lifted flat directions in broken supersymmetric potentials, proposed as natural candidates for small field inflation [3]. The nearly unbroken isotropy of the cosmic microwave background (CMB) provides an amusing counterexample to the well-worn notion that physicists enjoy spherical symmetry. Simply assuming that the universe began as a uniformly dense patch of radiation does not adequately explain this uniformity, which amounts to a fine-tuning of the universe’s initial conditions [4]. Inflation makes this uniformity plausible, because an epoch of exponential spatial expansion (de Sitter space) fueled by a near-constant vacuum energy and preceding the radiation and matter dominated expansions of our universe, provides a common origin for otherwise causally separated lightcones on our cosmic horizon, which at present time contains primordial photons of almost equal temperature, released when the formation of hydrogen made the universe more transparent. More concisely, the symmetry of a de Sitter space could be the source of spherical symmetry on the cosmic microwave background. But any such antecedent de Sitter space cannot be totally time symmetric: inflation must end so its effects can be observed. A simple mechanism that achieves this is a scalar field slowly-rolling down its potential, resulting in a slowly-decreasing vacuum energy that sources a quasi-de Sitter space. The necessary slowness of this roll can be quantified with the parameters m2pl Vφ 2 Vφφ ≡ φ < 1, m2pl ≡ ηφ < 1, (1) 2 V V where V (φ) is a scalar potential and Vφ ≡ dV is the slope of the potential. The expansion dφ fomented by this potential is measured with the scale factor of the universe, a ∝ eHt , where H ≡ aa˙ is the Hubble rate, which can be determined from the equations of motion and continuity for a scalar field sourcing de Sitter, 1 ˙2 φ¨ + 3H φ˙ + Vφ = 0, φ + V − 3m2pl H 2 = 0, (2) 2 where in the slow-roll limit the first term in each of these equations can be omitted. In order for our universe to be causally connected at the time of big bang nucleosynthesis, the universe needs to have expanded to roughly e60 times its initial size during inflation, where the exponent is called the number of efolds, N . The expansion rate gets larger with larger vacuum energy, V (φ), and inflation lasts longer with a smaller slope, Vφ . Thus it is sensible (and with Eq. (2) verifiable) that in the slow-roll limit, N takes the form Z te Z φe 1 V N= Hdt = 2 dφ, (3) mpl φ∗ Vφ t∗ 1 In this work we only consider multiple small field models which terminate inflation with the dynamics of the inflating fields themselves. These considerations will also apply to some (though not all) small multifield hybrid models [2]. Predictions for Sivers single spin asymmetries in one- and two-hadron electroproduction at CLAS12 and EIC Hrayr H. Matevosyan,1 Aram Kotzinian,2, 3 Elke-Caroline Aschenauer,4 Harut Avakian,5 and Anthony W. Thomas1 1 arXiv:1502.02669v1 [hep-ph] 9 Feb 2015 ARC Centre of Excellence for Particle Physics at the Tera-scale, and CSSM, School of Chemistry and Physics, The University of Adelaide, Adelaide SA 5005, Australia http://www.physics.adelaide.edu.au/cssm 2 Yerevan Physics Institute, 2 Alikhanyan Brothers St., 375036 Yerevan, Armenia 3 INFN, Sezione di Torino, 10125 Torino, Italy 4 Physics Department, Brookhaven National Laboratory, Upton, NY 11973, USA 5 Thomas Jefferson National Accelerator Facility, 12000 Jefferson Ave. Suite 5, Newport News, VA 23606, USA (Dated: February 11, 2015) The study of the Sivers effect, describing correlations between the transverse polarization of the nucleon and its constituent (unpolarized) parton’s transverse momentum, has been the topic of a great deal of experimental, phenomenological and theoretical effort in recent years. Semi-Inclusive Deep Inelastic Scattering measurements of the corresponding single spin asymmetries (SSA) at the upcoming CLAS12 experiment at JLab and the proposed Electron-Ion Collider will help to pinpoint the flavor structure and the momentum dependence of the Sivers parton distribution function describing this effect. Here we describe a modified version of the PYTHIA6 Monte Carlo event generator that includes the Sivers effect. Then we use it to estimate the size of these SSAs, in the kinematics of these experiments, for both one and two hadron final states of pions and kaons. For this purpose we utilize the existing Sivers parton distribution function (PDF) parametrization extracted from HERMES and COMPASS experiments. We also show that the the leading order approximation commonly used in such extractions provides significantly underestimated values of Sivers PDFs, as the omitted parton showers and non-DIS processes play an important role in these SSAs at lower light-cone momentum fraction, for example in the COMPASS kinematics. PACS numbers: 13.88.+e, 13.60.-r, 13.60.Hb, 13.60.Le I. INTRODUCTION The study of the structure of the nucleon has long been a focus of both theory and experiment within the medium and the high energy hadronic physics community, mostly concentrating on the distributions of the longitudinal momentum fraction of partons within nucleon described by the transverse momentum integrated (”collinear”) parton distribution functions (PDF). More recently, exploring the transverse structure of the nucleons in momentum space via transverse momentum dependent (TMD) PDFs and the generalized parton distribution functions in impact parameter space has attracted great interest. The spin of the nucleon and its constituent partons plays an important role when describing the transverse structure of the nucleon. Here we will focus on the so-called Sivers TMD PDF that describes the modification of the fully unpolarized TMD PDF when considering unpolarized partons inside of a transversely polarized nucleon [1]. The knowledge of the Sivers PDF is crucial in our understanding of the spin structure of the nucleon. It can be accessed in a variety of experiments in the so-called deep inelastic scattering (DIS) regime, where the probes intact directly with a parton inside of the target, such as the Drell-Yan process and semi-inclusive hadron production in polarized hadron-hadron collisions, or semi-inclusive DIS (SIDIS) of a lepton off a transversely polarized nucleon. In a SIDIS process with a single detected final state hadron, the Sivers PDF can be accessed through a term in the single spin asymmetry (SSA) modulated with the sine of the so-called Sivers angle [2], defined as the azimuthal angle between the transverse momentum of the detected hadron and the transverse spin of the nucleon. The amplitude of this modulation is given as a convolution of the Sivers PDF with the TMD unpolarized fragmentation function (FF) divided by a convolution of the unpolarized TMD PDF and TMD FF. Experimental measurements of these asymmetries have been performed by several collaborations: HERMES [3, 4], COMPASS [5, 6] and JLab HALL A [7], extracting sizable effects for both pion and kaon final states. The Sivers PDF has then been extracted in Refs. [8, 9] using phenomenological parametrizations of the involved PDFs and FFs to fit the experimentally measured SSAs. Unfortunately these parametrizations suffer from relatively large uncertainties arising from both theory and experiment. These uncertainties come from the experimental measurements themselves, the lack of knowledge of unpolarized TMD FFs (especially those for the unfavored channels [10], as well as those involving the strange quark [11]), and assumptions about the shape and the flavor dependences of both unpolarized and Sivers PDFs and unpolarized FFs. This is relevant, as in calculating SSAs one integrates over the transverse momentum and then sums over the type of struck parton. Moreover, in such extractions Prepared for submission to JHEP arXiv:1502.02667v1 [hep-ph] 9 Feb 2015 LUX likelihood and limits on spin-independent and spin-dependent WIMP couplings with LUXCalc Christopher Savagea,b Andre Scaffidic Martin Whitec Anthony G. Williamsc a Department of Physics & Astronomy, University of Utah, Salt Lake City, UT 84112 Nordita, KTH Royal Institute of Technology and Stockholm University, SE-106 91 Stockholm, Sweden c ARC Center of Excellence for Particle Physics at the Terascale & CSSM, Department of Physics, University of Adelaide b E-mail: [email protected], [email protected], [email protected], [email protected] Abstract: We present LUXCalc, a new utility for calculating likelihoods and deriving WIMP-nucleon coupling limits from the recent results of the LUX direct search dark matter experiment. After a brief review of WIMP-nucleon scattering, we derive, for the first time, LUX limits on the spin-dependent WIMP-nucleon couplings over a broad range of WIMP masses, under standard assumptions on the relevant astrophysical parameters. We find that, under these and other common assumptions, LUX excludes the entire spin-dependent parameter space consistent with a dark matter interpretation of DAMA’s anomalous signal, the first time a single experiment has been able to do so. We also revisit the case of spin-independent couplings, and demonstrate good agreement between our results and the published LUX results. Finally, we derive constraints on the parameters of an effective dark matter theory in which a spin-1 mediator interacts with a fermionic WIMP and Standard Model fermions via axial-vector couplings. A detailed appendix describes the use of LUXCalc with standard codes to place constraints on generic dark matter theories. Recoil-α-fission and recoil-α-α-fission events observed in the reaction 48 Ca+243 Am U. Forsberg,1 D. Rudolph,1 L.-L. Andersson,2 A. Di Nitto,3 Ch.E. D¨ ullmann,2,3,4 J.M. Gates,5 P. Golubev,1 5 6 7 2,4 K.E. Gregorich, C.J. Gross, R.-D. Herzberg, F.P. Heßberger, J. Khuyagbaatar,2 J.V. Kratz,3 K. Rykaczewski,6 L.G. Sarmiento,1 M. Sch¨ adel,4,8 A. Yakushev,4 S. ˚ Aberg,1 D. Ackermann,4 M. Block,4 H. Brand,4 B.G. Carlsson,1 7 2,3 9 D. Cox, X. Derkx, J. Dobaczewski, K. Eberhardt,2,3 J. Even,2 C. Fahlander,1 J. Gerl,4 E. J¨ager,4 B. Kindler,4 J. Krier,4 I. Kojouharov,4 N. Kurz,4 B. Lommel,4 A. Mistry,7 C. Mokry,2,3 W. Nazarewicz,6,9,10 H. Nitsche,5 J.P. Omtvedt,11 P. Papadakis,7 I. Ragnarsson,1 J. Runke,4 H. Schaffner,4 B. Schausten,4 Yue Shi,6,10 P. Th¨ orle-Pospiech,2,3 T. Torres,4 T. Traut,3 N. Trautmann,3 A. T¨ urler,12 A. Ward,7 D.E. Ward,1 N. Wiehl,2,3 1 Lund University, 22100 Lund, Sweden Helmholtz Institute Mainz, 55099 Mainz, Germany 3 Johannes Gutenberg-Universit¨ at Mainz, 55099 Mainz, Germany 4 GSI Helmholtzzentrum f¨ ur Schwerionenforschung GmbH, 64291 Darmstadt, Germany 5 Lawrence Berkeley National Laboratory, Berkeley, California 94720, USA 6 Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA 7 University of Liverpool, Liverpool L69 7ZE, United Kingdom Advanced Science Research Center, Japan Atomic Energy Agency, Tokai, Ibaraki 319-1195, Japan 9 University of Warsaw, 00681 Warsaw, Poland 10 University of Tennessee, Knoxville, Tennessee 37996, USA 11 University of Oslo, 0315 Oslo, Norway and 12 Paul Scherrer Institute and University of Bern, 5232 Villigen, Switzerland (Dated: February 11, 2015) arXiv:1502.03030v1 [nucl-ex] 10 Feb 2015 2 8 Products of the fusion-evaporation reaction 48 Ca + 243 Am were studied with the TASISpec set-up at the gas-filled separator TASCA at the GSI Helmholtzzentrum f¨ ur Schwerionenforschung. Amongst the detected thirty correlated α-decay chains associated with the production of element Z = 115, two recoil-α-fission and five recoil-α-α-fission events were observed. The latter are similar to four such events reported from experiments performed at the Dubna gas-filled separator. Contrary to their interpretation, we propose an alternative view, namely to assign eight of these eleven decay chains of recoil-α(-α)-fission type to start from the 3n-evaporation channel 288 115. The other three decay chains remain viable candidates for the 2n-evaporation channel 289 115. PACS numbers: 21.10.-k,23.20.Lv,23.60+e,27.90.+b In the quest for enhanced nuclear stability in the region of superheavy elements (SHE) – frequently defined as those with Z ≥ 104 – the two elements flerovium (Fl, Z = 114) and livermorium (Lv, Z = 116) have recently been officially approved [1]. The interpretation of data on odd-Z elements, however, is more challenging, while the study of nuclei with odd numbers of nucleons can be especially rewarding: The extra hindrance and thus delay for spontaneous fission (SF) renders other decay modes such as α decay and electron capture (EC) even more likely. Consequently, odd-Z nuclei potentially give rise to decay chains with more α-decay members than evenZ ones. Additionally, α decay of odd-A or odd-odd nuclei most often proceeds into excited states in the daughter nucleus, because unpaired nucleons typically tend to remain in the same single-particle orbitals as in the α-decay parent [2, 3]. Observation of electromagnetic decays from these excited states can thus elucidate the low-lying nuclear structure of the daughter [4]. Such experimental studies have recently reached decay chains of element Z = 115 [5], while observations of odd-Z elements beyond Rg have been reported up to Z = 117. See, e.g., Refs. [6–12] and references therein. The expected complex nuclear structure of odd-Z nuclei of SHE can easily translate into complex α-decay sequences. Interestingly, however, for the description of many of the hitherto published Z ≥ 113 decay chains it appears to suffice with just one type of α-decay sequence per isotope, be it 278 113 [12], 287−289 115 [9], or 293,294 117 [10, 11] (see also references therein). This simple but surprising picture might be due to limited statistics, combined with possibly comparable decay energies and half lives of different decay branches of a given isotope. In this paper, new data on recoil-α-(α)-SF events stemming from element Z = 115 are presented. A comprehensive assessment including corresponding data from Ref. [9] implies more complex decay sequences of 288,289 115 than presented in previous reports on these isotopes [8, 9, 13]. It is demonstrated that the plain length of an α-decay chain is not necessarily a good descriptor to define the reaction channel. The Universal Linear Accelerator (UNILAC) at the GSI Helmholtzzentrum f¨ ur Schwerionenforschung, Darmstadt, Germany, provided a 48 Ca8+ heavy-ion beam with a typical intensity of 6 × 1012 ions per second, averaged over the pulsed structure of the UNILAC (5 ms beam on and 15 ms beam off). The experiment was conducted at two beam energies: Beam integrals of 2.13(12) and 3.89(23) × 1018 48 Ca ions were collected at 5.400 and 5.462 MeV/u, respectively. Flavor decomposition of the nucleon electromagnetic form factors at low Q2 I. A. Qattan,1 J. Arrington,2 and A. Alsaad3 1 Khalifa University of Science, Technology and Research, Department of Applied Mathematics and Sciences, P.O. Box 127788, Abu Dhabi, UAE 2 Physics Division, Argonne National Laboratory, Argonne, Illinois, 60439, USA 3 Jordan University of Science and Technology, Department of Physical Sciences, P.O. Box 3030, Irbid 22110, Jordan (Dated: February 11, 2015) arXiv:1502.02872v1 [nucl-ex] 10 Feb 2015 Background The spatial distribution of charge and magnetization within the proton is encoded in the elastic form factors. These have been precisely measured in elastic electron scattering, and the combination of proton and neutron form factors allows for the separation of the up- and down-quark contributions. Purpose In this work, we extract the proton and neutron form factors from world’s data with an emphasis on precise new data covering the low-momentum region, which is sensitive to the large-scale structure of the nucleon. From these, we separate the up- and down-quark contributions to the proton form factors. Method We combine cross section and polarization measurements of elastic electron-proton scattering to separate the proton form factors and two-photon exchange (TPE) contributions. We combine the proton form factors with parameterization of the neutron form factor data and uncertainties to separate the up- and down-quark contributions to the proton’s charge and magnetic form factors. Results The extracted TPE corrections are compared to previous phenomenological extractions, TPE calculations, and direct measurements from the comparison of electron and positron scattering. The flavor-separated form factors are extracted and compared to models of the nucleon structure. Conclusions With the inclusion of the precise new data, the extracted TPE contributions show a clear change of sign at low Q2 , necessary to explain the high-Q2 form factor discrepancy while being consistent with the known Q2 → 0 limit. We find that the new Mainz data yield a significantly different result for the proton magnetic form factor and its flavorseparated contributions. We also observe that the RMS radius of both the up- and down-quark distributions are smaller than the RMS charge radius of the proton. PACS numbers: 25.30.Bf, 13.40.Gp, 14.20.Dh I. INTRODUCTION The electromagnetic form factors of the proton and (p,n) (p,n) neutron, GE and GM , are fundamental quantities which provide information on the spatial distributions of charge and magnetization in nucleons. The form factors are measured using electron scattering where the incident electron scatters from a nucleon target through the exchange of a virtual photon which serves as the sole mediator of the electron-nucleon electromagnetic interaction. By increasing Q2 , the four-momentum squared of the virtual photon, the virtual photon becomes more sensitive to the small scale internal structure of the nucleon. In electron scattering there are primarily two methods used to extract the proton form factors. The first is the Rosenbluth or Longitudinal-Transverse (LT) separation method [1], which uses measurements of the unpolarized cross section, and the second is the polarization transfer or polarized target (PT) method [2], which requires measurement of the spin-dependent cross section. A significant difference is observed between LT and PT extractions of the proton form factors [3, 4], which is currently believed to be the results of larger-than-expected two-photon exchange (TPE) contributions [5, 6]. In this paper, we extract the proton form factors from a combined analysis of LT and PT measurements, accounting for TPE contributions following the approach of Ref. [7], but with an emphasis on recent low-Q2 data. The combined analysis allows us to extract the TPE contribution to the e-p elastic cross section, which we compare to other phenomenological extractions and to direct calculations of TPE effects meant to be valid in the lower Q2 regime, as well as to recent direct measurements of TPE contributions from the comparison of electronproton and positron-proton elastic scattering [8, 9]. With the inclusion of neutron form factor measurements, we separate the nucleon form factors into their upquark and down-quark contributions [10, 11]. New cross section and polarization measurements at low Q2 allow for a more detailed examination of the flavor-separated form factors in the region sensitive to the large-distance behavior of the proton charge and magnetization distributions. We compare these results to previous extractions, as well as to models of the up- and down-quark contributions to the proton form factors. II. OVERVIEW OF THE METHODS A. Rosenbluth Separation Method In the Rosenbluth separation method, the reduced cross section σR for elastic e-p scattering in the Born or one-photon exchange (OPE) approximation is: 2 ε 2 σR = GpM (Q2 ) + GpE (Q2 ) , τ (1)

© Copyright 2020