Body & Exterior Hardware Prices subject to change Door Handle

Body & Exterior Hardware
Prices subject to change
Co
Door
Handle Bezel Spring Lock Washer
$12.50
BODY-0004
Laser cut spring steel lock washer for
use with the door handle bezel on
Cord L-29 and others.
Co
Cord
810 812 Trunk Lid Stay Flipper, Left
$123.75
COR-0024
Trunk lid stay flipper for the left hand
side of the trunk on all Cord 810 and
812 models.
Material: 1095 Spring steel; Finish:
Natural; Thickness: .020; OD: .896; ID:
.500
Co
Exterior
Co
Cord
Door Handle Bezel
$41.25
BODY-0002
Cast bronze door handle bezel used
on many custom bodied cars in the
1920's and 1930's including
Duesenberg Model J and Derham
Coachwork cars. Original part number
66046. For use with door handle, our
part number BODY-0001.
Length: 2.100; Width: 1.200; Height:
.410; Mounting holes: 1.500 centers
for #10 screws
Co
Exterior
Co
Cord
Door Handle
$128.75
BODY-0001
Cast bronze door handle with steel
shank. Used on many custom bodied
cars in the 1920's and 1930's
including Duesenberg Model J and
Derham Coachwork cars.
Handle and shank are threaded to
screw together. Shank should be
silver brazed in place after fitting and
before plating.
Handle can be supplied with shank
brazed in place for an additional
$15.00 charge. For use with bezel, our
part number BODY-0002.
Material: Bronze handle, steel shank;
Shank: 7/16-20 thread, 5/16 square x
3 7/8; Handle: 3.975 long, .935 wide,
1.950 high
Co
Murphy
Body Footman Loop
810 812 Trunk Lid Stay Flipper, Right
$123.75
COR-0025
Trunk lid stay flipper for the right hand
side of the trunk on all Cord 810 and
812 models.
Molded Rubber Round Door Bumper
$13.50
MISC-0022
Molded rubber round door bumper.
Measures 1 1/8 OD, 9/16 high
(approx.).
Co
Cord
Molded Rubber Lid Bumpers
$16.50
COR-0002
New molded rubber lid bumpers with
hole in the center for the attaching
screw. These are ready to install and
measure 15/16 Dia. and 9/16 h. Used
on Cord Convertible Coupe. Sold as a
set of four.
Co
Hispano
Suiza Bumper Bracket Bolt
$36.25
MB-0020
Bronze footman loop used on many
Murphy bodied cars. Used to hold
door check strap to door and body.
$12.50
HIS-0153
Steel bolt for the bumper bracket of
Hispano Suiza J-12. Hispano Suiza
part number B4597.
Material: Bronze; Finish:
Natural;Length: 3.105; Width: .632;
Height: .687; Stud holes: .272; Hole
centers: 2.375; Bar length: 1.666
Material: Steel; Finish: Natural;
Thread: M10 x 1.5; Thread length:
20mm; OAL: 47mm; Hex: 14mm;
Head height: 6mm; Length under
head: 41mm
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
1
Body & Exterior Hardware
Prices subject to change
Co
Voisin
Co
Packard
6 Cyl. Bumper End
$334.75
V-0007
Rubber molded bumper end with steel
core for use on 1934-1936 Voisin 6
cylinder. May also fit other years and
models. Price includes a $50.00 core
charge to be refunded upon receipt of
a usable core.
Material: Rubber & Steel;Finish:
Natural; Molded rubber: approx. 3.062
x 4.125; Steel core: 1.750 x 2.000;
Hole ID: .437
Co
Hispano
Suiza J12 Bumper Center
$412.00
HIS-0142
Rubber center piece for front and rear
bumpers used on European custom
bodied cars in the 1930's including
Hispano Suiza J12 and others.
Rear sill plates will fit:
15th,16th & 17th Series 7 Pass.
Touring Sedan
15th, 16th & 17th Series 7 Pass.
Touring Sedan Limo
15th, 16th & 17th Series 5 Pass. Club
Sedan
15th, 16th & 17th Series 5 Pass.
Convertible Sedan
17th Series 5 Pass. Victoria
Original Packard part numbers:
224307 (right) and 224308 (left).
Material: Urethane; Base: 120mm;
Height: 128mm; Overall thickness:
77mm; Clip length x width: 120mm x
39mm; Gap width: 6.5mm
Co
Packard
V-12 Rear Sill Plates
$77.25
P-0073
New photo engraved rear sill plates to
fit many Series and models of Packard
V-12. These perfect reproduction sill
plates have been photo-etched into
.032 brass and are exact duplicates of
the original Packard parts. The plates
are ready to be drilled and plated.
Rear plates are 1.375 x 17.187.
Co
Stutz
V-12 Front Sill Plates
$92.75
P-0072
New photo engraved sill plates to fit
many Series and models of Packard V12. These perfect reproduction sill
plates have been photo-etched into
.032 brass and are exact duplicates of
the original Packard parts. The plates
are ready to be drilled and plated.
Front sill plates are 2.562 x 34.935.
and will fit 1935 V-12 Convertible
Sedan. Original Packard part
numbers: 224317 (right) and 224318
(left).
Door Sill Plate, Long
$144.25
STZ-0016
Brass engraved door sill plate for use
on 1931 Stutz Model M.
Material: Brass; Length: 36.0; Width:
2.516; Thickness: .042; Height: .553;
ID Bend: .218
Co
Stutz
Door Sill Plate, Short
$144.25
STZ-0017
Brass engraved door sill plate for use
on 1931 Stutz Model M.
Material: Brass; Length: 18.00; Width:
2.482; Thickness: .042; Height: .617;
ID Bend: .218
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
2
Body & Exterior Hardware
Prices subject to change
Co
Murphy
Body Door Sill Plates
$133.00
MB-0010
Door sill plate to fit all Murphy bodied
cars of the 1920's and 1930's. These
sill plates are an exact duplicate of the
original shape, are made from .040
thick brass and measure 35 X 2 or 35
X 2 3/4". The Murphy logo is stamped
into the brass in the center of the plate.
These sill plates are produced to be
trimmed to fit and drilled by the
purchaser. They will also need to be
polished and plated by the purchaser.
Co
Auburn
Boattail Speedster Sill Plate
$154.50
AUB-0005
Aluminum sill plate for use on Auburn
Boattail Speedster. Sill plate has an
etched-in design and is an exact
duplicate of an original sill plate.
Material: Aluminum; Finish: Natural;
Length: 32.00; Width: 3.062;
Thickness: .052; Inner bend DIA: .557;
Width before bend: 2.00; Width after
bend: .312
Co
Maserati
Ghibli Sill Plate
Co
Saoutchik
Coachwork Door Bumper, Long
$15.50
BODY-0006
Rubber door bumper used on
Saoutchik bodied cars of the 1930's.
Material: Rubber; Length: 1.995;
Width: 1.100; Height: .535; Step
length: 1.595; Step width: .725; Step
height: .335
Co
Murphy
Body Door Bumper Sockets
$30.00
MB-0003
Murphy body door bumper sockets
CNC machined from solid aluminum.
Can be shortened to fit a specific
application. Both sockets have .030 lip
to overlap the door jams.
Available in two lengths:
Outside width: 1.355
Outside length: 1.719
Height: .488
Outside width: 1.355
Outside length: 1.106
Height: .488
Co
Door
Bumper Retaining Bracket
$130.00
MAS-0002
Universal aluminum sill plate for
Maserati Ghibli. Fits left and right side
of the car, but will need to be polished
and trimmed to fit before installation.
Maserati part number 115B064950.
$25.75
MISC-0310
Laser cut retaining bracket used to
install a rubber door bumper. For use
on many classic cars of the early
1930's such as Duesenberg and
others.
Material: Aluminum; Finish: Natural;
Width: 1.727; Length: 36.00;
Thickness: .050
Material: Steel; Finish: Natural;
Length: 1.260; Width: .806; Height:
.484; Thickness: .060; Holes: .205,
.336 centers
Co
Hooper
Body Door Hinge Bolt
$41.25
MISC-0274
Steel door hinge bolt for use on
Hooper bodied cars of the 1920's and
1930's.
Co
Saoutchik
Material: 4140 Steel; Finish: Natural;
Thread: BSF 5/16-22; Thread length:
.387; OAL: 1.667; Length under head:
1.425; Head OD: .768; Shaft OD: .387;
Square: .305
Material: Rubber; Length: 1.675;
Width: 1.385; Height: .492; Step
length: 1.295; Step width: .835; Step
height: .250
Version 11/20/2014
Coachwork Door Bumper
$15.50
BODY-0005
Rubber door bumper used on
Saoutchik bodied cars of the 1930's.
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
3
Body & Exterior Hardware
Prices subject to change
Co
Dovetail
Door Bumper Socket
Co
Window
Flapper Spring #1
$51.50
MISC-0068
Ideal door bumper socket. New fully
machined aluminum part to replace
original die cast Ternstedt Mfg. Co.
part. Used with a steel capped rubber
bumper, this dovetail socket has four
mounting holes to hold the socket to
the car body, has four holes tapped for
8-32 screws to retain the cover plate
and two pockets for bumpers.
$8.75
MB-0001
Stainless steel spring for closing
window flappers. Commonly used on
Murphy bodies, this style has clock
wise wind & long ends coming off on
the same side. Also used by Brunn,
Rollston, LeBaron and others.
Measures 1.260 with a .218 OD wire.
Wire thickness is .040. Ends can be
trimmed and bent if needed.
Available in two pocket sizes: 1/2" or
5/8". Outside dimensions: 3" long x 1
11/32 wide x 5/8 high. Interior
dimensions: 1 1/8 x 9/16 deep.
Co
Window
Co
Hooper
Body Door Hinge Screw
$5.25
MISC-0277
This M7 x 1.00 door hinge screw has
an oversized shank for repairing worn
hinges. For use on Hooper bodied
cars of the 1920's and 1930's, such as
some Hispano Suizas.
Material: Steel; Thread: M7 x 1.00;
Thread length: 8mm; OAL: 26mm;
Head OD: 9mm; Head height: 5mm;
Shaft: 7mm; Length under head: 21mm
Co
1929-32
Cadillac Door Light Switch
$165.00
CAD-0140
Chrome plated door jamb switch for
use on 1929 - 1932 Cadillac. Ready to
install.
Material: Steel; Finish: Chrome;
Bracket: 1.750 x 1.125; Bracket holes,
centers: .190, 1.375; Button OD: .375;
Button height: .359
Co
Door
Window Flapper Hinge
$77.25
MISC-0324
Special hinge with 5/8" knuckles to
cover the window opening when the
window is rolled down. Sold in a five
foot length - trim to fit application.
Flapper Spring #2
$8.75
MB-0002
Stainless steel spring for closing
window flappers. Commonly used on
Murphy bodies, this style has counter
clockwise wind with long ends coming
off on opposite sides. Also used by
Brunn, Rollston LeBaron and others.
Measures 1.130 OAL with a .218 OD
wire. Wire thickness is .040. Ends can
be trimmed and bent if needed.
Co
Window
Flapper Spring #3
$8.75
MB-0004
Stainless steel spring for closing
window flappers. Commonly used on
Murphy bodies, this style has
clockwise wind with long ends coming
off on opposite sides. Also used by
Brunn, Rollston, LeBaron and others.
Measures .935 OAL with a .169 OD
wire. Wire thickness is .034. Ends can
be trimmed and bent if needed.
Co
Window
Flapper Spring #4
$8.75
MB-0005
Stainless steel spring for closing
window flappers. Commonly used on
Murphy bodies, also used by Brunn,
Rollston, LeBaron and others.
Measures .584 OAL with a .224 OD
wire. Wire thickness is .040. Ends can
be trimmed and bent if needed.
Material: Steel ; Length: 5ft;
Thickness: .038; Knuckle: .625; Pin
DIA: .093; Open width: 3.000
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
4
Body & Exterior Hardware
Prices subject to change
Co
1932-33
Packard Windshield Locking Mechanism
Link
$51.50
P-0143
Linkage for the windshield locking
mechanism on 1932 and 1933
Packard. Used in adjusting the angle
of the windshield and securing it in
place. Packard part numbers 194987
and 194988. For use on:
1932 Standard 8509, 523, 527
1932 Deluxe 8 519, 533, 537
1932 12 578, 579, 583, 587
1933 Standard 8 618, 619, 623, 627
1933 Super 8 658, 659, 663, 667
Pleated Hood Pad Material
19.25 / Sq. Ft.
MISC-0246
Diamond pleated hood pad material
for use on Italian cars such as
Maserati, Ferrari, Lamborghini and
others. Consists of an insulating pad
sewn between two layers of vinyl
coated fabric. The diamond in the
material shown is 3.437 point to
point. Distance between the stitching
is 2.375. Other sizes and patterns can
be custom sewn in sizes up to 5ft x
4ft - contact our Parts Office for further
information on our custom design
service. This item is sold by the
square foot. Largest size available is
5ft x 4ft. Item is made to order and
additional handling time of 7 days will
apply.
Material: Vinyl & insulation; Thickness:
0.125; Diamond: 3.437 point to point
(as shown in photo - other
patterns/sizes available as noted).
Co
Auburn
851 852 Hood Hinge
$51.50
AUB-0001
Hood hinge for Auburn 851/852 hood
sides. Specially made for use on
Auburn, but may also fit other makes
of automobiles.
Hood Bumper Nut
$2.25
CAD-0075
10-24 Heavy nut for the top hood
bumper on 1925-1929 V-8 Cadillac
and LaSalle. Cadillac group number
13.0041, part number 120361. Listed
in Cadillac parts book as "Button to
top panel nut".
Material: SS; Finish: Natural; Thread:
10-24; Hex: 3/8; Height: .197
Co
1930-33
Material: Spring steel; Finish: Natural;
Length: 6.975; Width: .675; Thickness:
.042; Hole ID: .110
Co
Diamond
Co
Cadillac
Cadillac Hood Rest Bracket
$36.25
CAD-0092
Steel hood rest bracket attaching to
center hinge on 1930 - 1933 Cadillac
V8, V12 and V16. 2 used per car on
models 345C, 3555, 370, 452BC. 4
used on all other models. Cadillac part
number 882679, group number
13.0216.
Material: Steel; Finish: Natural;
Length: 2.930; Width: 2.766;
Thickness: .056; Holes: .157 ID, 2.00
centers
Co
Cadillac
Hood Hinge Nut
$2.25
CAD-0074
6-32 Nut for all 1925-1936 Cadillac V8, V-12 and V-16 and LaSalle hood
hinges. Cadillac group number
13.0094, part number 113102. Listed
in Cadillac parts book as "Top panel
hinge screw nut".
Material: SS; Finish: Natural; Thread:
6-32
Co
Aluminum
J Molding
$36.25
MISC-0271
Aluminum "J" molding for use in
various automotive and marine
applications.
Length: 48"; Width: 1.038; Thickness:
.038
Material: Steel; Pin: 3/16; Knuckle:
2.00; Open width: 1 1/4; Thickness:
.060; Length: 60"
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
5
Body & Exterior Hardware
Prices subject to change
Co
Ghia
Coachwork Hood Latch Spring
$25.75
MISC-0197
Hood latch spring used with some
Ghia bodied cars from the 1950's.
This spring was produced for
installation with a Ghia Supersonic
body on an Aston Martin DB 2/4.
Hood Louver Door Springs
$14.25
P-0097, P-0098
Right and left side hood louver door
springs for 1938-39 Packard V-12.
Packard part numbers:
Right: 242118R, group 0.01901
Left: 242118L, group 0.01901.
6 Springs per side required.
Material: Stainless steel; Finish:
Natural; Wire: .115; OD: 1.49; Free
length: 1.475
Co
Ghia
Co
Packard
Coachwork Hood Support Spring
$87.75
MISC-0208
Spiral torsion spring used as a hood
support spring for cars with Ghia body
coachwork. This spring was produced
for the hood support on a Ghia
Supersonic body on an Aston Martin
DB 2/4.
Material: SS; Finish: Natural; Wire
DIA: .072; OD: .395; LOB: 1.585; OAL:
7 1/4
Co
Packard
Hood Rivet, Short
$10.50
P-0088
Packard hood rivet, short version.
Material: Steel; Finish: Natural; Width:
.300; OD: 2 11/16; Thickness: .078;
End loop ID: 11/32
Co
Hood
Door Spring, 1929-31 Packard
$20.75
P-0126
Hood door spring for 1929-1931
Packard. 6-8 Springs required per car
depending on model.
Packard part number 147283, "Bonnet
Side Door Hinge Spring". For Packard
Series 300 - 800.
OAL: 2 1/2; Wire size: .085; Loop OD:
.357; "U" Length & width: 11/16 x .445
Co
Packard
Hood Rivet, Long
$12.50
P-0089
Packard hood rivet, long version.
Co
Hood
Door Spring, 1930-31 Cadillac & LaSalle
$20.75
CAD-0082
Hood door spring for 1930-1931
Cadillac and LaSalle. For use on:
1930-1931 Cadillac: 355A V8; 370A
V12; 452A V-16
1930-1931 LaSalle: 345A V8
One spring required for each hood
door - total of 10 required per car.
Cadillac group number 13.0316, part
number 882235.
OAL: 3 1/2; Loop OD: 1/2; Wire size:
.092; "U" Length & width: 1 1/32 x
13/16
Co
Stutz
Hood Vent Door Knob
$18.75
STZ-0003
Steel knob for the hood vent door as
used on Stutz SV-16 and DV-32.
Quantity of 8 used per car.
Material: Cold rolled steel; Finish:
Natural; Thread: 6-32; Thread length:
.290; Head: .620 OD x .505 long;
Length under head: .605; Step under
head: .182 OD; OAL: 1.110
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
6
Body & Exterior Hardware
Prices subject to change
Co
Stutz
Co
Maserati
Hood Hinge End Plate
$128.75
STZ-0006
Steel hood hinge end plate for Stutz
DV-32. Used to hold the hinge pin to
cowl and radiator.
Material: Steel; Finish: Natural;
Length: 2.500; Width: .853; Height:
.583; Holes: .312 ID, 1.776 center; Cut
out: 1.080 x .140; Hood ID: .453
Co
Cadillac
V-8 V-16 Tail Light Conduit Hanger
$32.50
Various Part Numbers
Steel strap to support spring type
wiring conduit used on 1929-1930 V-8
and 1930-1931 V-16 Cadillac. May
also be applicable to other years and
models. Two sizes available.
Cadillac group number 14.1995, part
number 872298.
CAD-0063: Length: 6 1/4; Width at
center: .650; Width at end: 1 1/8;
Thickness: .035; Hole DIA: .342;
Holes center to center: 5.130
Tail Light Stanchion Fender Plate
$69.75
STZ-0014, STZ-0015
Steel support plate for the tail light
stanchion on Stutz M, SV-16 and DV32. Attaches under the fender.
Available in left and right side
placement: STZ-0014 Left, STZ-0015
Right
Co
License
Lens for Tail Lights
$31.00
J-6475-27
Plate Frame, Prewar Automobiles
$77.25
MISC-0178
Chrome plated adjustable license
plate frame. Used on automobiles of
the late 1930's and early 1940's.
OD: 7/16; Minimum width: 8.00;
Minimum height: 4.00
Dark red tinted plastic material.
Duplicate of color used in 1930's tail
lamps.
Sold in a standard size of 9" x 4 1/2" x
.030 thick for $30.00. Can also be
made to order in custom sizes up to
23" x 53" priced at $.75 per square
inch, rounded to the nearest inch.
Contact us directly to order custom
sizes.
Version 11/20/2014
Co
Stutz
Material: Steel; Finish: Natural;
Length: 3.785; Width: 2.445;
Thickness: .040; ID of bend: .500;
Holes: .343
CAD-0064: Length: 6 1/4; Width at
center: .650; Width at end: 1 1/8;
Thickness: .035; Hole DIA: .342;
Holes center to center: 5.130
Co
Pyraline
Ghibli Side Reflector Marker Light
$113.50
MISC-0108
Maserati Ghibli side marker light
produced from solid brass. This side
marker is ready to be plated and is a
replacement housing for the original
plastic unit that cannot be plated.Fits
some years of Maserati Ghibli, may
also fit other models. Measures 2
13/16 OD. Specially produced for a
Ghibli owner who wanted to replace
his deteriorated original lights with a
quality replacement.
Co
Rolls
Royce Phantom I II Bumper Center Spacer
$128.75
RR-0004
Front and rear bumper spacer for use
on Rolls Royce Phantom I and
Phantom II Brewster bodied cars.
Spacer fits between back bar and face
bars where the center medallion
attaches. CNC machined steel.
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
7
Body & Exterior Hardware
Prices subject to change
Co
Duesenberg
J Running Board Channel
$92.75
J-7328
Brass J-shape channel used to finish
the inside edge of Duesenberg
running boards. Can also be used as
binding molding for a variety of vintage
cars and boats.
Measures 72" long x 1.093 high x .032
thick.
Co
Stewart
Warner Spotlight Tag
$56.75
STW-0023-5
Identification tag for a windshield
mounted combination spotlight and
rear view mirror made by Stewart
Warner. For use on Duesenberg
Model A and others.
Warner Spotlight Mirror
$103.00
STW-0023-6
Glass mirror for use on Stewart
Warner windshield mounted
combination spotlight / rearview
mirror. For use on Model A
Duesenberg and possibly other cars of
the era.
Material: Silvered glass; OD: 2.616;
Thickness: .092
Co
Stewart
Warner Spotlight Base
$92.75
STW-0023-1
Brass mounting base connecting to
the support arm of a Stewart Warner
spotlight. The spotlight mounts to the
windshield and is a combination
spotlight and rearview mirror. This is a
CNC machined duplicate of the
original part.
For use on Model A Duesenberg and
possibly other cars of the era.
Base: 2.750 L x .875 W x .375 H;
OAH: .9375; ID: .625; Screw holes:
.208, 2.25 centers
Version 11/20/2014
Warner Spotlight Faceted Nut
$51.50
STW-0023-3
Brass faceted nut securing the
spotlight assembly to the support arm
on Stewart Warner windshield
mounted spotlight / rearview mirrors.
For use on Duesenberg Model A and
possibly other cars of the era.
Material: Brass; Finish: Natural;
Thread: 1/4-24; Thread depth: .393;
Hex: .750; Hex height: .240; OAH:
.481; Step ID: .531
Co
Stewart
Length: 1.500; Width: .500; Thickness:
.028; Holes: .076 ID, 1.281 centers
Co
Stewart
Co
Stewart
Warner Spotlight Lens
$128.75
STW-0023-4
Glass lens for Stewart Warner
windshield mounted combination
spotlight / rearview mirror. For use on
Model A Duesenberg and possibly
other cars of the era.
OD: 3.916; Thickness: .092
Co
Stewart
Warner Spotlight Support Arm
$386.25
STW-0023-2
Bronze support arm for a Stewart
Warner windshield mounted
combination spotlight / rear view
mirror. This arm holds the light /
mirror assembly and attaches to the
mounting base. Recommended for
use with our spotlight base (STW0023-1) to ensure a snug fit. For use
on Model A Duesenberg and possibly
other cars of the era.
Material: Bronze; Width: 4.832;
Height: 3.9375; ID between the arms:
4.300; Mounting stem hex: .623 x
.550; ID on ends: .512
Co
Rear
Fender Sheet Metal T-Nut
$14.00
P-0033
Steel t-nut with 5/16-24 thread. Has 2
3/16 holes for attaching to body sheet
metal. Used on Packard and other
cars to hold rear fenders to the body.
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
8
Body & Exterior Hardware
Prices subject to change
Co
Cadillac
5/16-24 x 7/8 Sheet Metal Hex Bolt
$3.00
CAD-0128
5/16-24 x 7/8 Hex bolt for attaching
front fenders and corner shields on
1927 - 1929 Cadillac V8. Finished in
black oxide to prevent rustCadillac
part number 120213, alternative group
number 25.0500.
Material: Steel; Thread: 5/16-24;
Finish: Black oxide; OAL: 1.125;
Length under head: .875; Thread
length: .781; Hex: .500; Head: .250
Co
Cadillac
5/16-18 x 3/4 Sheet Metal Hex Bolt
Material: Steel; Thread: 5/16-18;
Finish: Black oxide; OAL: 1.00; Length
under head: .750; Thread length: .656;
Hex: .500; Head: .250
5/16-18 x 7/8 Sheet Metal Hex Bolt
$3.00
CAD-0125
5/16-18 x 7/8 Hex bolt for attaching
fenders and other body panels on V8,
V12, V16 Cadillac and LaSalle. Used
from 1927 - 1936. Finished in black
oxide to prevent rust. Cadillac part
number 120229, alternative group
number 25.0500.
Co
Cadillac
5/16-18 x 1 1/8 Sheet Metal Hex Bolt
$3.00
CAD-0126
5/16-18 x 1 1/8 Hex bolt for attaching
fenders and other body panels on V8,
V12 and V16 Cadillac and LaSalle.
Used from 1927 through 1936.
Finished in black oxide to prevent rust.
Cadillac part number 122022,
alternative group number 25.0500.
Material: Steel; Thread: 5/16-18
;Finish: Black oxide; OAL: 1.375;
Length under head: 1.125; Thread
length: .875; Hex: .500; Head: .250
Version 11/20/2014
Material: Steel; Finish: Black Oxide;
Thread: 5/16-18; Hex: .500; Length:
.460
5/16-24 x 1/2 Hex Nut
$3.00
CAD-0124
5/16-24 Hex nut for attaching mud pan
shelves on 1932 - 1936 Cadillac V8,
V12 and V16. Finished in black oxide
to prevent rust. Cadillac part number
120368, alternative group number
25.0080.
Material: Steel; Finish: Black oxide;
Thread: 5/16-24; Hex: .500; Length:
.460
Co
Gas
& Radiator Cap Retaining Cup, 2 Ears
$25.75
LIN-0012-B
Gas and radiator cap retaining cup
with two ears. For use with Lincoln V12 1935 - 1939 and 1938 Packard.
May also fit other makes and years of
vehicles.
Material: Brass; Finish: Natural; DIA:
1.900; Square hole: 7/16; Height:
.444; Thickness: .062
For use with our part numbers: LIN0013, LIN-0014
Co
Gas
Material: Steel; Thread: 5/16-18;
Finish: Black oxide; OAL: 1.125;
Length under head: .875; Thread
length: .781; Hex: .500; Head: .250
5/16-18 x 1/2 Hex Nut
$3.00
CAD-0123
5/16-18 x 1/2 Fender bolt hex nut for
V8, V12, V16 Cadillac and LaSalle.
Cadillac part number 120376,
alternative group number 25.0080.
Co
Cadillac
$3.00
CAD-0127
5/16-18 x 3/4 Hex bolt for attaching
fenders and other body panels on
Cadillac V8, V12, V16 and LaSalle.
Used from 1927 - 1936. Finished in
black oxide to prevent rust. Cadillac
part number 881857, alternative group
number 25.0500.
Co
Cadillac
Co
Cadillac
& Radiator Cap Retaining Cup, 3 Ears
$25.75
LIN-0012
Gas and radiator cap retaining cup
with three ears. One ear is wider than
the others. For use with Lincoln V-12
1935 - 1939 and 1938 Packard. May
also fit other makes and years of
vehicles.
Material: Brass; Finish: Natural; DIA:
1.812; Square hole: .417; Height:
.390; Thickness: .062
For use with our part numbers: LIN0013, LIN-0014, LIN-0011
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
9
Body & Exterior Hardware
Prices subject to change
Co
Gas
& Radiator Cap Retaining Cup, 3 Ears Round
Hole
$25.75
LIN-0012-C
Gas and radiator cap retaining cup
with three ears. One ear is wider than
the others. This style has a round
center hole instead of a square hole.
For use with Lincoln V-12 1935 - 1939
and 1938 Packard. May also fit other
makes and years of vehicles.
& Radiator Cap Backup Washer
$10.50
LIN-0013
Gas and radiator cap backup washer
with cupped shape. For use with
Lincoln V-12 1935 - 1939 and 1938
Packard. May also fit other makes
and years of vehicles.
Material: Brass; Finish: Natural; OD:
2.500; ID: .767; Height: .150;
Thickness: .030
& LaSalle Radiator Filler Cap Washer
$25.75
CAD-0098
Brass radiator cap filler washer with
cupped shape. For use on Cadillac
and LaSalle from 1929 - 1932. May
also be compatible with other vehicle
makes. Cadillac part number 89157,
group 6.0897
For use on:
1929-1932 Cadillac V8, V12, V16
1932 LaSalle
Material: Brass; Finish: Natural; OD:
2.750; ID: .750; Thickness: .030
Co
Maserati
For use with our part numbers: LIN0012 or LIN-0012-B, LIN-0014, LIN0011
Co
1934-37
Lincoln V-12 Gas Cap Assembly
$360.50
LIN-0011
Complete new gas cap assembly for
1935-1939 Lincoln V-12. This
assembly has a chrome plated
aluminum cap with a brass lock plate.
Precision CNC machined and ready
for installation.
Co
Cadillac
Material: Brass; Finish: Natural; OD:
1.800; Height: .375; ID: .383;
Thickness: .060; Ears: .406 x .125
Co
Gas
Co
1935-39
Packard Radiator Cap Retaining Washer
$51.50
P-0167
Three eared brass radiator cap lock
plate used on Packards from 1934 1937. Packard part number 194829
Radiator Cap Tag
$46.50
TAG-0037
Red and silver radiator cap tag for
Maserati 3500 and other early 6
cylinder models.
Material: Aluminum; Finish: Natural;
OD: 2.105; Thickness: .018; Hole ID:
.100; Hole centers: 2.250; Width: 2.531
Material: Brass; Finish: Natural; OD:
1.770; Height: .359; ID: .375; Wall:
.067; Tab: .424 x .125
Co
Gas
& Radiator Cap Sealing Washer
$3.25
LIN-0014
Gas and radiator cap sealing washer
made from 1/32 gasket paper. For use
with Lincoln V-12 1935 - 1939 and
1938 Packard. May also fit other
makes and years of vehicles.
Material: Gasket paper; OD: 2.500; ID:
.791; Thickness: .025
For use with our part numbers: LIN0012 or LIN-0012-B, LIN-0013, LIN0011
Version 11/20/2014
Classic & Exotic Service, Inc., 2032 Heide, Troy, MI 48084 USA
10
`