Model CSL24VDC

VEHICULAR SLIDE GATE OPERATOR
Commercial DC
Model CSL24VDC
Gate Operator and
Accessory Site Plan
1
2
3
4
5
6
7
8
9
10
1
5
Imagine your Customers being
at the office and receiving an
alert if they left their garage
or gate open. Or being able to
turn on their lights before they
get home. The 828LM Internet
Gateway, which connects to your
Customer’s router and enables
smartphone control, does this by
letting them monitor, open and
close their garage door or gate
from anywhere and control home
lighting.
1
10
2
Standard edges will cause a gate
to stop or reverse when it meets
an obstruction while closing.
6
MPEL
Mounting Plate for Post
Mounting
For post mounting model
CSL24VDC commercial slide
operator. Posts not included.
MSEL
Mounting Stand
892LT & 894LT
2-Button and 4-Button
Security+ 2.0™ Learning
Remote Controls
65-MG020-5
Sensing Edge (Non-Monitored)
Internet Gateway
2
MyQ® Enabled Indoor Controls
Remote Controls
Photoelectric Sensors
Loop Detectors
Edge Sensors
Mounting Plate and Stand
Solar
Batteries
Heater
dwellingLIVE
828LM*
Steel stand for mounting to
concrete pad.
7
These remote controls are ideal
for gated communities. One
button can control a gate operator
and the other(s) can control
a garage door. It can also be
programmed to different codes
and frequencies.
SOLPNL20W12V
20 Watt 12V Solar Panel
Ideal for remote and sunny areas
without access to an AC outlet.
Two required.
SOLPNL10W12V
10 Watt 12V Solar Panel
811LM & 813LM
Universal DIP Single-Button
and 3-Button Remote Control
Two required.
8
7
5
29-NP712
7Ah 12V Battery
These remote controls are ideal
for applications such as gated
communities or commercial
applications requiring a large
number of remotes for a common
entrance.
Standard 7 AMP-Hour Battery, 12
Vdc, to replace original batteries
provided with operator. Reuse
existing harnesses.
A12330SGLPK
3
3
8
The photoelectric sensors are
designed to detect an obstacle in
the path of the electronic beam
and stop the operator. Includes
mounting brackets.
9
9
Low power through beam
photoelectric sensors, 45 foot
sensing distance, NEMA 4 rated.
Works in conjunction with Power
Management System to save
power.
Customer:
Date:
LOOPDETLM
Plug-In Loop Detector
Plug-in Loop Detector,
(LOOPDETLM) innovative design
includes 8 sensitivity settings &
boost, ensures vehicles are easily
identified.
Project:
Architect/Engineer:
Contractor:
Gate Weight (lbs.):
Heater kit for pad mount
operators. Protects system to
-40ºF. Installs on operator frame.
10
dwellingLIVE
Advanced Visitor
Management and Access
Control Solution
• Credentialed Access
4
ORDER SUMMARY
HTR
Heater Kit
Photoelectric Sensor
(Monitored)
LiftMaster gate operators comply with UL 325 standards. Important: To be compliant with UL 325 and industry safety guidelines, qualified monitored external
entrapment protection devices such as photoelectric sensors or edge sensors are required to be installed with this operator.
LiftMaster.com
Upgrade 33 AMP-Hour
Battery, 12 Vdc. Ideal for solar
applications and extended
battery backup. Two required.
CPS-UN4
4
Power Source (120 or 240 VAC):
33Ah 12V Battery
Photoelectric Sensor
(Monitored)
6
Gate Length (ft.):
CPS-RPEN4GM
Solar (Y/N):
* LiftMaster® Internet Gateway Accessory functionality is
dependent on communication with a MyQ® Enabled gate
operator. MyQ® Technology communication can be limited
by distance and type of exterior building materials. A
general range estimate is 300 ft.
• Visitor Management
• Telephone Entry Systems
• License Plate Recognition
• Community Websites
• Mobile Patrol
• Front Desk Concierge
VEHICULAR SLIDE GATE OPERATOR
Commercial DC
Model CSL24VDC
Installation Blueprint
TYPICAL INSTALLATION
INSTALLATION DIMENSIONS
OPERATOR POWER SOURCE
NOTE: One or more non-contact sensors shall be located where the risk
of entrapment or obstruction exists at either the opening or closing
direction. Care shall be exercised to reduce the risk of nuisance tripping,
such as when a vehicle, trips the sensor while the gate is still moving.
Any gap between the gate and a fixed object such as a wall, pillar,
column or the operator itself larger than 2 1/4 inches must be filled.
Wire Gauge
120 Vac
240 Vac
14
130 feet
260 feet
12
205 feet
410 feet
10
325 feet
650 feet
8
520 feet
1040 feet
6
825 feet
1650 feet
4
1312 feet
2624 feet
OPERATOR DIMENSIONS
DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR
20"
4"(10 cm)
21.1"
26"
(66 cm)
NOTE: Use copper conductors ONLY.
SINGLE GATE
Warning Sign
Safety Catch Roller
14.6"
24" (61 cm)
Edge
Sensor
CONCRETE PAD AND OPERATOR ATTACHMENT
Edge Sensor
Photoelectric
Sensors
CONDUIT LOCATION
4 Concrete
Anchors
1/2" x 3 1/2"
Operator
5-5/8"
1/2"
MOUNTING FOOTPRINT
(Gate)
7"
11.9"
1-1/4" 3-1/2" min. 1-2" 2-3/4"
10.3"
2-1/4"
2.85"
1-3/8"
Check national and local
codes for proper depth
(Conduit)
6" Above Ground
Earth Ground Rod
.63"
10.4"
14.1"
26"
Below the frost line.
Check all national
and local codes.
Water Tight
Conduit
(Not provided)
8"
NOTE: Power and control wiring
MUST be run in separate conduits.
DUAL GATE
13" 23"
Safety Catch Roller
Warning Sign
26"
(66 cm)
24"
(61 cm)
4-1/2"
14.6"
15"
(Pad)
24"
Edge Sensor
SAFETY LAYOUT
Monitored Photoelectric Sensors
Operator
Sensors for Open Cycle
NOTE: Wired connection in
a dual gate setup is optional.
Operators can be setup for wireless
dual gate communication.
Edge Sensor
!
© 2014 LiftMaster All Rights Reserved
845 Larch Ave., Elmhurst, IL 60126
LiftMaster.com
01-37414B
e
id ty
ts r
u e
O op
r
P
Check national and local
codes for proper depth
NOTE: Power and control wiring
MUST be run in separate conduits.
e y
id rt
s e
In op
r
Earth Ground Rod
P
Water Tight Conduit
(Not provided)
ey
id t
s er
In p
ro
P
Photoelectric
Sensors
PrOuts
op id
ert e
y
Sensors for Close Cycle
`