HYDRAULIC COMPONENTS MobilePower Mobile

MobilePower
HYDRAULIC
COMPONENTS
www.fleetpride.com
V3-1.2014
MobilePower
FleetPride is proud to
distribute these and many
other national brands
We are committed to reducing your downtime by getting you the
parts you need, when you need them. That’s why we offer the most
recognized brands from the top manufacturers in the industry,
and exclusive brand products that deliver both quality and value.
®
2
MOBILE POWER
3
TABLE OF CONTENTS
PRODUCTS
PAGE(S)
Cylinders
4
Parker - Mobile Cylinders - Double & Single Action - Hoist - Telescopic - Tie Rod
PTO’s
Chelsea - Bezares USA - Muncie - Mechanical, Clutch & Powershift Units - PTO Flanges - Valves & Pumps
Directional & Control Valves
Parker/Gresen - Monoblock - Relief - Accessory - Directional Control - Sectional Control Valves
Gear Pumps / Motors
Parker - Vantage Power - Single & Multiple Pumps / Motors - Cast Iron - Dump Pumps
Vane Pumps / Refuse
Permco - Denison - Vickers - Live/Moving Floor/Dump Trailers - Clutch Pumps - Single/Dual Vane - Refuse
Industrial Pumps / Motors
Permco - Roller Bearing Pumps/Motors - Sleeve Bushing Pumps/Motors
Piston Pumps / Motors
Bezares USA - Parker - Hydro Leduc - Bent Axis - Variable & Displacement - XA & MA Series
Motors
Eaton-Char-Lynn - Parker - H & S Series - 2000 Series - Small & Large Frame
5-8
9 - 10
11 - 13
14 - 15
16
17
18
Blowers / Pumps / Compressors
19
Vacuum Pumps / Coolers
20
Miscellaneous
21
Paragon - Blackmer - Ingersoll-Rand - Ranger - Roper - P857 Blower - Product Pumps - Oil/Oil Free Compressors
Fruitland - Challenger - Masport - Paragon - SS Thermaflow - Vacuum/Pressure Pumps - Hydraulic Oil Coolers
Road Watch Temperature Controls - Line Filters - Clutch Pump Parts - Valves/Fittings - Test Equipment - Cylinders
Consoles / Controls
Apsco - Vantage Power - Cross - Air Actuators - Consoles/Hoist & PTO Controls - Lift Axle Accessories - Stackable
Swivel Pedestals - Directional Control
Cable Controls
Cablecraft - Wescon - Button/Push-Pull Standard - Micro Adjust - Custom - Remote Control System Assemblies
22 - 23
24
Controllers
25
Wet Line System Products
26
Vantage Power
27
Parker - Dickey-John - Single - Dual Spreader Control - QDB Series - Control Point - LT Control
Vantage Power - Complete Systems - Combo Kits - Hydraulic Reservoirs Aluminum/Polyethylene & Steel
Pneumatic Air Controls - Hydraulic Gear Pumps - Dump Pumps - Reservoirs
Not all parts and/or components are in stock at every location. The parts in this catalog are manufactured by either the original equipment manufacturer or
aftermarket parts manufacturers. The original equipment manufacturers’ names, drawings, colors and part numbers, are used for identification purposes only
and we are in no way implying that all of our products are original equipment parts. FleetPride or the FleetPride Mobile Power Division is not liable for damages
due to omissions or typographical errors.
4
MOBILE POWER
MOBILE CYLINDERS
Your Leading Source
For Hydraulic Cylinders
FleetPride carries the industry leading brand name cylinders from Parker Commercial Intertech.
We can supply your needs for welded type single & double acting, telescopic, hoist, and tie rod cylinders!
Cylinder Applications
l Dump Trucks
l Dump Trailers
l Roll Off Hoist
l Refuse Packers & Many More!
Contact your local FleetPride location or FleetPride Mobile Power
toll free at 888-338-5352 or fax 203-287-3720
for availability and technical support.
Download our FREE Mobile App today!
MOBILE POWER
POWER TAKE OFFS - PTO
5
 Power Take Off - pto
Proper Matching of PTO
A Power Take-Off must be properly matched to the vehicle transmission and to the auxiliary equipment being powered. An improperly
matched P.T.O. could cause severe damage to the vehicle transmission, the auxiliary driveshaft, and/or the auxiliary equipment being
powered. Damaged components or equipment could malfunction causing serious personal injury to the vehicle operator or to others
nearby. Always refer to Chelsea catalogs, literature, and owner’s manuals, and follow Chelsea recommendations when selecting,
installing, repairing, or operating a PTO.
Mechanical Shifted Units
The mechanical shifted power take-offs such as the 442 Series family is engineered to work with virtually
all existing transmission applications today. There are many advantages to these units from a removal
shift cover to establish correct backlash during installation, greaseable output shafts that help solve fretting
corrosion problems, and a positive shift engagement. With a wide selection of shift, speed ratios, and output
options, that can be easily converted to meet your needs, these units are a true workhorse for most vehicle
applications either with air brakes or without, manual or automatic transmissions.
Powershift Units
Chelsea Powershift PTOs deliver clash free shifts whether the vehicle is stationary or on the move.
Constant mesh input gears and specially designed clutch packs make these PTOs ideal for applications
that demand frequent PTO shifting, such as refuse vehicles. These units are available with over seven of
today’s most popular pump mounting flanges, Electronic Overspeed Control (EOC) to protect driven
equipment from over-speeding, and pressure lubrication for heavy duty applications. Fixed compression
gasket eliminates setting of backlash and reduces installation time. Special low profile housing designs
for vehicle interference issues are also available making the Chelsea Powershift PTOs a very wise selection
for today’s demanding applications.
442 Series
 Engineered to work with virtually all existing
 transmission applications
 Economical workhorse features a cast
 iron housing
 Tapered cone bearings for high torque
 rating and long service life
 Slip fit idler pin for easy interchange from
 one transmission to another
 Easy to set backlash
 Wide range of shift and output options
489 Series
 442 Series family, but with an 8-bolt
 mounting flange
 No adapter plate needed
 Less installation time, less expense and
 less chance of leakage
 Wide range of shifter options and
 pump flanges
278 Series - allison world
 Enhanced housing design for
 maximum transmission clearance
 when direct mounting a pump
 6 speed ratios and 14 output options
 Internal bearing lube
 SuperTorque™ gears available for
 20% higher intermittent torque
 ratings
 Electric/hydraulic shift
560 Series
 Wet spline for extended PTO and pump
 shaft life
 Single continuous duty torque rating
 Torque rating of 335 lbs. ft. (454 N.m.)
 Flow rates 3.4 to 31.7 GPM
 (12.9 119.9 LPM) at 1200 RPM
 Pressure ratings up to 3500 PSI (240 bars)
 12 or 24 volt electric over hydraulic actuation
 Pressure and sucion ports rotatable for
 best clearance
 Weight 71 lbs. no pump bracket required
 Quiet operation
6
MOBILE POWER
POWER TAKE OFFS - PTO
 Power Take Offs pto
280 Series - New
230/231 Series
 This new series utilizes the best of Cheslea
 technology and innovations from the current
 Hot Shift PTO’s.
 The 280 series will combine the 277 and 278
 into one model of PTO.
 It will feature a single continuous duty
 torque rating. No more intermittent rating.
 Torque capacity ratings have been
 increased.
 Pump clearance issues have been
 improved with rotatable cast iron flanges.
 New positive stop for Driveline outputs.
 Eliminates ability for shaft couplings to
 damage Oil Seals.
 speed ranges expanding from 5 ratios to
 9 ratios.
 Designed for both manual and automatic
 transmissions.
 231 offers low profile housing for avoiding
 clearance problems.
 Pressure lubrication option available for
 both units.
 Patent pending internal self adjusting
 shaft brake option.
 Air or electric air shift unit
236 Series
 Patent pending internal self adjusting shaft
 brake option.
 Wide selection of input gears for virtually
 all currently produced transmissions.
 Helical gears and optional pressure
 lubrication to extend PTO service life.
 Inspection cove for adjusting backlash.
 Air or electric air shift unit.
890 Series
Mounting a flange to the rear of the transmission
allows for larger pumps and in some cases it
will eliminate the need for a drive shaft.
 Require less space than current P.T.O.’s and
 helps clear frame rails, etc.
 Torque ratings up to 670 ft. lbs. and allows 
 the use of higher flow and pressure pumps.
 The 890 Series can be installed in 2 pieces;
 one lighter P.T.O.housing and then the shaft.
 Wet Spline outputs – Extends shaft life.
 Eliminates the need to disassemble to 
 frequently grease the splines.
870 Series
 The 870/877 Series is a 10-bolt mounting
 pattern that will fit on today’s popular
 automatic transmissions.
 Features six shift options four of which are
 integrated into the P.T.O. housing that
 require one hose for a simplified installation.
 Eight internal gear ratios provide you with
 a wide variety of speeds to meet your
 application requirements.
 The direct mount pump flange options are
 available with our Wet Spline Design that
 provides you with increased P.T.O. and
 pump shaft life.
 Versatility, power, ease of maintenance
 and installation, make the 870 Series the
 only choice for your vocational truck
 requirements.
249 Series
Quieter and more cost-effective, the
Chelsea 249 Series teamed with the new
Ford Transmission Noise Suppression System,
provide a quiet PTO application on
your Ford SuperDuty - Patent Pending.
 No special installation tools to purchase
 eliminating costs and saves time.
 Single Hose connection and
 Integrated Actuation Valve.
 Single hose simplifies installation and
 reduces installation time along with
 eliminating leak paths.
 Intermittent Torque Rating of 200 ft. lbs.
 58 Horsepower @ 1200 Engine RPM
 Two Year Warranty.
 Pump flows up to 25.1 GPM @ 1200
Engine RPM – Standard.
 Flanges
 RA Flange
 sae b 2 bolt
489RA Features:
 Most common application is on small trucks using an Allison
 World Transmission where clearance is very important when
 bolting a piston or gear pump that has an SAE B 2 bolt pump.
MOBILE POWER
POWER TAKE OFFS - PTO
7
Bezares has been manufacturing PTO’s for the world market for over 50 years and are a leader
in European and Asian PTO development, manufacturing, and distribution. Working closely with the truck
and transmission manufactures from around the world, Bezares USA gives us a distinct advantage in the
global PTO market. All Bezares PTO’s are built with the highest quality bearings and sealing components.
1000/2000 Series
116003 Series
3100/3150/3250 Series
6013399/602199
to 609699 Series
The 1000 and 2000 series PTO’s have been
engineered to work with the most common
transmissions in today’s market. Offered in a
wide range of input gear, ratio, output, and
shifter options, these all cast iron PTO’s
include large 12mm flange bolts, which make
for a very sturdy and durable pump mount,
supporting some of the larger pumps in the
market. Both of these models are also available
in a deep mount 1010 and 2010 series.
3100 and 3250 series are 10 bolt hotshift PTO’s
for the Allison World Series transmissions as well
as the new Caterpillar CX series. These PTO’s
have seven ratio options, a wide variety of
outputs, and either electric over hydraulic or
air shift options. The 3250 series is a low profile
version of the 3100 for tight mounting spaces on
certain truck chassis. The 3150 is the constant
mesh option of this series.
3200 Series
This versatile 6 bolt hotshift PTO is designed
for the 1000/2000 Allison transmission family,
Asian automatics and a wide range of manual
transmissions. The 3200 series is offered with
multiple ratios and outputs, as well as electric
over hydraulic and air shift options.
3900/3920 Series
Our 3900 and 3920 series PTO’s have been
designed for the Ford F- Series Torqueshift
transmissions. Both PTO’s have both a direct
as well as a remote mount output option.
4000 Series
One of Bezares’ most popular products, the
4000 series PTO is a very compact, heavy duty,
high torque, eight bolt PTO that was design at
an economical price. It has a wide variety of
ratio and output options as well as an
integrated air shift cover for extra durability.
4200 Series
The 4200 series PTO is a market exclusive
dual output eight bolt heavy duty PTO. This unit
has two independently air operated outputs,
with a variety of ratio and output combinations.
This PTO is very versatile for many applications
where two PTO’s are needed and only one
opening is availible
Bezares currently manufactures and offers
nine different PTO options to fit these specific
transmissions around the world. Models include
our standard 116003, a hot shift, a heavy duty,
a single gear, and a triple output PTO amongst
others. All of these PTO’s are available with
any SAE or DIN output options.
The Model 6013399 Split Shaft PTO is
designed to provide up to two 6 bolt PTO
mounting apertures for light to medium duty
vehicles that may not have the PTO option or
are limited to one opening. This split shaft may
also offer the ability to pull more torque and
horsepower than a transmission mounted PTO
may be capable of providing. A wide range of
Bezares PTO’s can be installed on the openings
with the full range of PTO options. The PTO’s
and split shaft have the options of being shifted
pneumatically, mechanically or hydraulically.
The 6013399 split shaft PTO mounts in the
main driveline behind the transmission or
behind any driveline output providing input
speeds based upon the
input shaft speed.
901211 Series
Selector Valve
Selector valve 901211 is a two position, two
selector valve that offers a simple means of
directing oil flow into two separate hydraulic
circuits. It is air operated with an open center
in neutral position. Max flow 65 gpm, maximum
pressure 5000 psi.
9030890 Series
Hi/Low Hydraulic Valve
The 9030890 valve is an air operated dual
pressure tippingvalve with two independent
operating pressures. This valve is a perfect fit
for a walking floor and dump combination,
or even a standard dump body when ordered
without the HP option. At a fraction of the
cost of other options.45 gpm rated and
maximum pressure 5000 psi.
8
MOBILE POWER
PTO / PUMPS
 PTO’s
TG Series Powerflex™ PTO
Our first major new product, the TG Series, has had a major impact on
the PTO market in North America, with others emulating the features
and benefits of the design. The TG Series is the industries’ most
popular and versatile PTO design, and is still the heart of the Muncie
PTO product family. The TG’s flexibility permits a wide variety of
PTO/transmission applications, and wide gear design permits torque
capacity for most truck equipment applications.
Clutch Shift PTOs
Clutch Shift PTOs provide the ability to engage and disengage the PTO
without disengaging the vehicle’s clutch. They can be designed for
both manual and automatic transmissions and are the preferred type
of PTO for automatics. Muncie offers clutch style PTOs for SAE standard
PTO openings as well as providing application specific models such
as the FA and GM products.
FA SERIES
The FA Series PTO was designed in cooperation
with Ford Motor Company for the 1999 and newer Super
Duty chassis equipped with the 4R100 automatic transmission. The FA62 two wheel drive and FA64 four wheel
drive mount on the driver’s side, offer a variety of direct
mounted hydraulic pumps. The PTOs are shipped complete with in-dash activation controls and transmission
temperature gauge as well as a complete wiring harness.
Six Shifting Choices
Air Shift
Cable Shift
Lectra Shift
Lever Shift
CS6 & CS8 SERIES
The CS6 & CS8 Series PTOs are built for SAE standard
6 and 8 bolt opernings. A wide variety of gears allow
the use of this PTO on manual transmissions
as well as Allison’s family of
AT & MT Series automatics.
 Pumps
Muncie carries a
complete line of
hydraulic pumps
including gear, vane,
and piston models.
Hydraulic Pumps
All pumps are pressure balanced and 100% tested before shipment.
f series gear pump
The F Series is the smallest of the gear pump family. It is designed with sleevetype bushings and an aluminum housing to provide high performance in a compact, lightweight package. The F Series is available in a number of configurations
for special low flow applications or for general duty.
k/l series gear pump
Both K & L Series pumps are constructed for maximum versatility. These pumps are offered with SAE 2
& 4 bolt “B” mounting patterns and a variety of shafts
as well as foot-mounted flanges. Standard pumps
can be used as either a pump or hydraulic motor with
side an rear ports machined into the housings.
EOS-110 Overspeed Switch
The EOS-110 disengages auxiliary power equipment
PTOs and pumps - when an excessive operating
speed is reached. It automatically re-engages
equipment when engine is reduced to a safe speed.
This allows full operator control within predetermined
limits. Speeds can be adjusted from 300 RPM to
3000 RPMs. Easily adaptable to any gasoline or
diesel engine. No mechanical connections are required.
h series gear pump
The H Series is most commonly used as the basis for our clutch pump product
line, but is also offered in a variety of direct mount SAE “A” or remote mount
configurations. The H Series is built with a cast iron housing and long life sleeve
type bearings.
clutch pump & mounting kit
Clutch pumps are driven directly off the pulley system at the front
of the engine. Kits are available for most popular engine/chassis
combinations with either v-belt or poly groove compatibility.
Clutch pumps are popular for applications requiring live
engine power or for chassis without
PTO accessibility.
Refuse & Specialty Gear Pumps
power pro & power miser systems
These products can be driven from the engine
crankshaft or by a PTO. Each provides hydraulic
power at the flip of a switch. In the “off” mode, pumps
receive only enough oil for lubrication purposes,
saving the cost of moving fluid through the system
when not in use.
mlsm live pak system
The MLSM Live Pak system is designed for
start and stop refuse collection equipment.
The system does not shut off the pump at
high RPM and provides flows up to the maximum
allowed for the equipment without interruption.
This allows for minimum cycle times, increasing
the number of collections per shift.
MOBILE POWER

Two types of directional valves can be used: Open-Center valves (CFO)
and Closed-Center valves (CFC). The two types of valves give completely
different control characteristics.
CFO valves are intended for applications in which simple, uncomplicated
components are required, and where the demands for simultaneous operation
characteristics are moderate. CFC valves are intended for applications in
which the demands on control characteristics are great, while at the same time,
a system with a fixed pump is required.
Parker valves can be obtained with a large number of optional
components and mountings such as:
 A main pressure relief
 Individually adjusted port relief and anti-cavitation valves
 Separate replenishing valves with counterpressure valves
 Application adapted spools and/or a large selection of spool actuators
 Single or multi-pump operation by stacked valves
 Subplate, stackable, or manifold styles
 Load hold checks - crossover reliefs - flow controls - power beyond feature
 Proportional inlets for finer metering
 E-stop, pump channel blocked in emergency - valve options vary
 Flows up to 197 LPM - 52 gpm
 Load Sensing
The directional control valve: In the load sense system, the directional control
valve regulates the displacement of a variable displacement pump via a load
signal line. The pump maintains a pressure difference between its outlet port
and the highest load signal to supply pressure and flow to match the demand.
These systems are the most advanced, offering optimum control characteristics
with good efficiency/fuel economy.
Parker valves can be obtained with a large number of optional
components and mountings such as:
 A main pressure relief
 Individually adjusted port relief and anti-cavitation valves
 Separate replenishing valves with counterpressure valves
 Application adapted spools and/or a large selection of spool actuators
 Single or multi-pump operation by stacked valves
 Subplate, stackable, or manifold styles
 Load hold checks - crossover reliefs - flow control
 Variable or fixed pumps
 Flows up to 302 LPM - 80 gpm
Gresen V20 Series Directional
Applications:




9
Directional Valves
 Constant Flow

DIRECTIONAL VALVES
Snow And Ice Control Systems
Utility Equipment - Dump Bodies - Spreaders
Recovery Vehicles & Refuse Equipment
Lube Trucks & Cranes
Features:
 High tensile ductile iron for durability and shock load resistance
 Compact size and lightweight to fit your installation needs
 Precision machined spools with extra find metering control and low spool forces
 Available in SAE or NPT porting
 Stackable design to customize to your needs
 Large variety of spool types and backcap options
 Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors,
 pilot operated check valves - lock valves - and power beyond capabilities
V20 TECHNICAL DATA
Design Type: Sectional
Circuit: Open Center Design
Parallel, Tandem, Combined
Parallel/Tamdem, & Series
Also: Closed Center, Load Sensing,
Load Sensing/Pressure Comp
Available.
Capacity: 30 GPM - 76 LPM
Nominal - 20 GPM - 114 LPM
Maximum - 30 GPM
Max. System Pressure: 3500 psi
Max. Tank Pressure: 200 psi
Filtration: 33 Micron
Spool Force: 50 lbs Maximum
Temperature: 020°F - 180°F
Or -29°C - 82°C Seal Type:
Buna-N Standard Optional Viton
Relief Valves: Shim Adjust,
Optional Screw Adjust Inlet
10
MOBILE POWER
CONTROL VALVES
 Control Valves
 Commercial DVA20/DVG20 Sectional
DVA20 & DVG20 Features:
 Steel castings for durability and shock load resistance for your high pressure needs
 Full flow relief valves and low open center pressure drop
 Parallel circuit design permits all spools to be operated independently or simultaneously with
 the lightest load receiving priority
 Precision machined spools are hard chrome plated for maximum life and corrosion resistance
 Stackable sectional design allows for customizing the assembly to your specific needs
 Modern machinery and SPC manufacturing procedures produce assemblies with minimal
 internal leakage to maintain maximum load holding ability
 Work sections are 100% pre-assembled and pre-tested before shipping
 Large variety of spool types and backcap actions. Transition load checks are standard to prevent
 load shift between spool positions
 Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors, and H.P.C.O.
 power beyond providing flexibility for all your design needs
DVA20 Inlet
DVA20 & DVG20 TECHNICAL DATA
Design Type: Sectional
Circuit: Parallel/Open Center
Capacity: 40 GPM - 152 LPM - Nominal
Capacity: 60 GPM - 228 LPM - Maximum
Max. System Pressure: 2500 psi - 172 Bar - SAE O.D.T.
Max. System Pressure: DVA Series 2500 psi - DVG Series 3500 psi
Max. Tank Pressure: 160 psi
Spool Force: 50 lbs - 22.7 kg - Maximum
Temperature: -20°F - 200°F Or -29°C - 93°C
Seal Type: Buna-N S
Relief Valves: Differential Type Adjustable From 800 To 2500 psi - 55.1 to 172 Bar - Preset At 2000 psi - 138 Bar
 Commercial DVA35/DVG35 Sectional
DVA35 & DVG35 Features:
 Steel castings for durability and shock load resistance for your high pressure needs
 Full flow relief valves and low open center pressure drop
 Parallel circuit design permits all spools to be operated independently or simultaneously with
 the lightest load receiving priority
 Precision machined spools are hard chrome plated for maximum life and corrosion resistance
 Stackable sectional design allows for customizing the assembly to your specific needs
 Modern machinery and SPC manufacturing procedures produce assemblies with minimal
 internal leakage to maintain maximum load holding ability
 Work sections are 100% pre-assembled and pre-tested before shipping
DVA35
 Large variety of spool types and backcap actions. Transition load checks are standard to prevent
 load shift between spool positions
 Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors, and H.P.C.O.
 power beyond providing flexibility for all your design needs
DVA35 & DVG35 TECHNICAL DATA
Design Type: Sectional
Circuit: Parallel/Open Center
Capacity: 60 GPM - 226 LPM - Nominal
Capacity: 90 GPM - 342 LPM - Maximum
Max. System Pressure: DVA Series 2500 psi - DVG Series 3500 psi
Spool Force: 50 lbs - 22.7 kg - Maximum
Temperature: -20°F - 200°F Or -29°C - 93°C
Seal Type: Buna-N
Relief Valves: Differential Type Adjustable From 1500 To 3000 psi - 103.5 to 207 Bar - Preset At 2000 psi - 138 Bar
Mid-Section
Inlet
DVG35
GEAR PUMPS / MOTORS 11
MOBILE POWER
 Gear Pumps & Motors
P16
Single and Multiple Pumps and Motors
 P16™
Features:
TP16
Series
TP16
 Flow range to 38 gpm - 143.8 LTR
 Displacements to 3.902 CIR - 63.94 CC’s/rev.
 Maximum pressure to 3000 psi - 207 bar
 Maximum speed to 3600 rpm
 Rotation A or C
 Bearings - Journal
 Cast iron gear plate w/aluminum flange & cover plate
CP16
Clutch Pump
General P16 Information:
PVP16
Priority Valve
 P20™
 Available in various configurations
 Cast iron pumping sections for durability
 Aluminum flanges and covers for optimum
 power to weight ratio
 Journal bearings for long life & good over-hung
 load capacity
 Pressure balanced plates for greater efficiency
Series
Features:
 Flows to 41 GPM
FLOW RATE BY GEAR SET SIZE
SPEED
 Pressures to 3000 PSI
GEAR WIDTH & GEAR OUPUT (GMP/LPM)
RPM
1”
14”
12”
1w”
2”
900
6.5
8
10
12
13.5
1200
9
11.5
14
16
18.5
1500
11.5
14.5
17.5
20.5
23.5
21
25
29.5
34
2100 16.5
 P30/031™
 Speeds to 2400 RPM
PRESSURE RATING BY GEAR SIZE
Gear Set Size 0.50
IN3
1
Max RPM
2400
P20 - Max PSI 3000
0.75
1.5
2400
3000
1.00
1.97
2400
3000
1.25
2.5
2400
3000
1.50
2.96
2400
3000
1.75
3.45
2400
2500
2.00
3.94
2400
2500
Series
FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED
SPEED
RPM
900
1200
1500
1800
2100
2400
WIDTH & GEAR OUPUT (GMP/LPM)
1”
6.5
24.5
9
34
11.5
43.5
14
53
16.5
62.5
19
72
14”
8
30
11.5
43.5
14.5
55
18
68
21
79.5
24
91
12”
10
38
14
53
17.5
66
21.5
81.5
25
94.5
29
110
1w”
12
45.5
16
60.5
20.5
77.5
25
94.5
29.5
112
34
129
2”
13.5
51
18.5
70
23.5
89
29
110
34
129
39
148
Features:
 Flows to 41 GPM - Pressures to 3000 PSI
 Speeds to 2400 RPM
 Priority valves - 2 speed valves & piggybacks
 Winch motors
Gear Set Size
IN3
Max RPM
P30 - Max PSI
P31 - Max PSI
PRESSURE RATING BY GEAR SIZE
1.00
0.50
0.75
1.50
1.25
1.97
1
1.5
2.96
2.5
2400
2400
2400
2400
2400
2500
2500
2500
2500
2500
3000
3000
3000
3000
3000
1.75
3.45
2400
2250
2500
2.00
3.94
2400
2250
2500
12
MOBILE POWER
PUMPS / MOTORS
 P50/P51™
Series
Single and Multiple Pumps and Motors
FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED
SPEED
RPM
900
1200
1500
1800
2100
2400
WIDTH & GEAR OUPUT (GMP/LPM)
1”
8.5
32
12
45.5
15
57
18
68
21.5
81.5
25
14”
10.5
39.5
15
57
19
72
23
87
27
102
31
2”
17.5
66
24
91
31
117
37.5
142
44
167
51
1w”
15
57
21
79.5
27
102
32.5
123
38.5
146
44
12”
13
49
18
68
23
87
27.5
104
32.5
123
37
24”
20
75.5
27
102
35
132
42
159
49.5
187
57
22”
22
83.5
30
114
39
148
47
178
55
208
63.5
Features:
PRESSURE RATING BY GEAR SIZE
 Flows to 63 GPM - Pressures to 3000 PSI
 Speeds to 2400 RPM
 Priority valves - 2 speed valves - piggybacks
 Winch motors flow
Gear Set Size
IN3
Max RPM
P51 - Max PSI
0.50
1.29
2400
3000
0.75
1.93
2400
3000
1.00
2.57
2400
3000
1.25
3.22
2400
3000
1.50
3.86
2400
3000
1.75
4.5
2400
3000
2.00
5.15
2400
3000
 P75/76™
Series
Single and Multiple Pumps and Motors
FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED
SPEED
RPM
1”
900 11.5
32
17
1200
45.5
22
1500
57
1800 27.5
68
33
2100
81.5
38
2400
14”
15.5
39.5
22
57
29
72
33.5
87
42
102
49
WIDTH & GEAR OUPUT (GMP/LPM)
2”
22”
24”
1w”
12”
27
34.5
30.5
23
19.5
2w”
38
3”
42
27
68
35.5
32
79.5
41.5
37.5
91
48
42
102
54.5
48
114
61
52.5
114
67
58
114
74
43.5
51
59
66
74
81.5
90
51.5
60
69.5
78
87
96.5
106
59.5
70
80
90
101
111
122
Features:
 Flows to 128 GPM
 Pressures to 3000 PSI
 Speeds to 2400 RPM
PRESSURE RATING BY GEAR SIZE
Gear Set Size
IN3
Max RPM
P76 - Max PSI
P75 - Max PSI
0.50
2.02
2400
2500
3000
0.75
3.03
2400
2500
3000
1.00
4.04
2400
2500
3000
1.25
5.06
2400
2500
3000
1.50
6.07
2400
2500
3000
1.75
7.08
2400
2500
3000
2.00
8.09
2400
2500
2500
2.25
9.2
2400
2250
2500
2.50
10.25
2400
2250
2500
2.75
11.1
2400
2000
2000
3.00
12.1
2400
2000
2000
2.25
5.79
2400
2500
2.50
6.43
2400
2500
MOBILE POWER
 P300/P400™
Series
Single and Multiple Pumps and Motors
cast iron bushing pump
Features:
 Three piece cast iron construction
 Low friction bushing design
 Heavy duty application
 Single, multiple, piggy back
 and thru-drive assemblies
PUMPS / MOTORS 13
Model
P = Pump
M = Motor
Options
D = Stealth
Gear
Width
.50
.75
P315
1.00
M315
1.50
1.25
1.75
2.00
.50
.75
P330
1.00
M330
1.50
1.25
1.75
2.00
.50
.75
The P300 Series pumps are available in single, multiple, piggyback, and thru-drive
assemblies. Multiple pumps reduce mounting costs, allow for a small package size
and common inlet capabilities. Assemblies up to six pumping sections are available.
Piggyback pumps allow the combination of pump sections of different frame size
to use a common inlet in tandem configuration. The thru-drive feature allows an
independent piston or gear pump to be mounted to a rear SAE drive pad.
Multiple section motors are also available providing enhanced torque and speed
control as well as smooth torque ripple.
The P400 Series of high pressure, fixed displacement gear pumps are available
in single and multiple assemblies. These units are rated for service up to 4500 psi.
They’re available in three models offering you a displacement range from 1.5 to
5.5 CIR. These units are cast from high-strength iron which provides the structural
integrity needed at high pressures. Gear widths have been selected to keep shaft
deflections and bearing loads within acceptable design limits. Body seals have been
strengthened and the fastener pre-load increased to assure reliability
under high pressure conditions.
 C102™ Series Pump
1.00
P350
1.25
M350
1.75
1.50
2.00
2.25
2.50
.75
1.00
P365
M365
1.25
1.50
1.75
2.00
2.25
2.50
Theoretical
Displacement
in3/r
.620
.930
1.24
1.55
1.86
2.17
2.48
.965
1.47
1.97
2.46
2.95
3.44
3.94
1.28
1.91
2.55
3.19
3.82
4.46
5.10
5.73
6.38
2.70
3.60
4.50
5.40
6.30
7.20
8.10
9.00
Mineral Oil / Maximum Pressure
Continuous
Intermittent
cm3/r
10.2
15.2
20.3
25.9
30.5
35.6
40.6
16.1
24.2
32.3
40.4
46.4
56.5
64.6
20.9
31.3
41.8
52.2
62.7
73.1
83.6
94.0
104.5
44.3
59.0
73.8
88.5
103.3
118.0
132.8
147.5
psi
3500
3500
3500
3500
3300
2900
2500
3500
3500
3500
3500
3500
3250
3000
3500
3500
3500
3500
3500
3250
3000
2700
2500
3500
3500
3500
3500
3500
3500
3250
3000
bar
psi
245
245
245
245
225
200
175
245
245
245
245
245
225
210
245
245
245
245
245
225
210
190
175
245
245
245
245
245
245
225
210
4000
4000
4000
3850
3500
3100
2750
4000
4000
4000
4000
3850
3500
3300
4000
4000
4000
4000
3850
3500
3300
3000
2750
4000
4000
4000
4000
4000
3850
3500
3300
bar
275
275
275
265
245
215
190
275
275
275
275
265
245
225
275
275
275
275
265
245
225
210
190
275
275
275
275
275
265
245
250
 Dump Pumps
Heavy Duty
Cast Iron
Features:
 Patented Relief Valve Protection
 Pressure To 2500 psi
 Flows From 9.5 To 48 gpm
 Includes G101/G102 Series
 Speeds To 2400 rpm
 2 & 3 Line Installation
 Air Shift Kits Available
C102 Dimensions
VantagePower PN
VPC-101-25-Z-MS-25
Parker PN
C101D25
VPC-102-25-Z-L-MS-25
C102D-25-1
VPC-102-25-Z-L-AS-25
––––
VPC-102-25-Z-R-MS-25
C102D25
Description
Remote mount
twin shaft
DIRECT MOUNT LH
DIRECT MOUNT LH
with air shift
DIRECT MOUNT RH
14
MOBILE POWER
PUMPS / REFUSE
 Heavy Duty Pumps
For Live And Moving Floors
and Dump Trailers
 Heavy Duty Clutch Pumps
CP124 With Pad
Mounting, Side
And Rear Porting
Features:
Dual Use Pump Features:
 Dual Pressure Relief: low for dump bodies, high for live floors
 Easy to switch from low to high pressure using truck air
 Large 12” NPT suction port in the gear housing
 Three line system for continuous duty
 Field adjustable relief settings
 Doweled construction
 37 GPM @ 1800 RPM - 100% factory tested
 Heavy duty “controlled stress” roller bearings
 Factory installed “OEM” air shift with full metering capabilities
 Direct mount SAE “B” 4 bolt or twin shafted remote mount
 with bracket
 Relief valve protects the high pressure portion of the system
 as well as the pump
Gemini Dimensional Data - Inches
CP124 With
Bracket Mount,
Side SAE O-Ring Ports
 Cubic inch displacements from 0.62 through 2.48
 Speeds to 3000 RPM and pressures to 3500 PSI
 SAE “A” mounting with bracket or pad mounting available
 Heavy duty sleeve bushing design in a small frame size
 Doweled and high strength 3 piece cast iron construction
 100% factory tested
 NPT, o-ring, or split flange porting located on the rear and/or side
 Only high torque clutches used with all the popular clutch
 configurations available
 Pressure balanced wear plates maintain high pump efficiency
 throughout all operating ranges
 Typical applications include recovery vehicles, snow plows,
 spreaders, utility vehicles, winches, small hoists, aerial
 devices, lift gates, cranes, and light duty equipment
Gear
Width
(Inches)
.50
.75
1.00
1.25
1.50
1.75
2.00
Displ
CU IN/CC
.62/10
.93/15
1.24/20
1.55/25
1.86/30
2.17/35
2.48/40
GPM/
LITERS @
1000 RPM
2.2/8.3
3.6/13.6
4.9/18.5
6.1/23.1
7.4/28.0
8.8/33.3
10.0/37.9
Max
RPM
3000
3000
3000
3000
3000
3000
3000
Min
RPM
600
600
600
600
600
600
600
Max
PSI/BAR
3500/241
3500/241
3500/241
3500/241
3200/220
2900/200
2500/172
CP124 Performance Chart/Specifications
 Dual Pressure Controller
The third sleeve is installed in the pump, therefore, the return port
must be plumbed back to tank, below the oil line at all times.
Gemini dual use pumps are designed to be
used with dual use applications, typically a
dump trailer and a live floor or goose neck.
Gemini Dual-Use Pump Specifications
Series
IN3(CC)
DG-20/RG-20 5.12
(84.3)
GPM/900 RPM GPM/1200 RPM GPM/1500 RPM Max Max
2000 PSI
2000 PSI
RPM PSI
2000 PSI
30.5
30.5
1800 3200
30.5
AVC-295-HP-13
This special dual pressure controller is to be used in the Gemini
pump system. Features PTO On/Off / Dump raise/lower.
In addition, it has an optional high pressure switch that allows the
Gemini pump to switch into high pressure
mode for live floor application and
warning light letting you know that
you are in high pressure mode.
Console comes equipped with a
warning beeper to ensure you
are in high pressure mode
MOBILE POWER
VANE PUMPS / REFUSE 15
 Vane Pumps
FleetPride carries a complete line of Vane Pumps
by these manufacturers:
Featuring a complete line of replacement Vicker® and Denison® vane pumps, FleetPride
offers a large selection of balanced rotor vane pumps that directly interchange with
Vickers® and Denison®. With a variety of displacements, mounting flanges and output shafts,
these pumps have grown to be a mainstay in both mobile, industrial & refuse applications.
These Denison vane type units come in many
sizes and configurations. They are seen in refuse
equipment where flow is electronically controlled to
gain maximum efficiency for both the hydraulic
system and fuel economy.
 Refuse Systems
PT6 / PT7 Series
Single Section Vane Type
These EVO vane type units come in many sizes
and configurations. They are seen in refuse equipment where flow is electronically
controlled to gain maximum efficiency for both the hydraulic system and fuel economy.
This type units is commonly found on commercial and residential front and rear loaders
with single hydraulic systems.
EVO PT6 / PT7 Series
Tandem Section Vane Type
The PT6 and PT7 series are common on many
of today’s refuse hydraulics systems; tandem units
provide the ability to operate (2) independent hydraulic systems
with one pump. These type units are seen on automated side loader refuse vehicles
where two different flow rates are required for the packer and grapple arm. The flows
are electronically controlled to provide constant flow to each hydraulic system to
maintain efficiency for the hydraulic system and provide optimum fuel ecomony.
EVO Refuse Features:
 Rust resistant coated; noneed for paint
 Bi-rotation; simplifying field adjustment
 Longevity and reliability; trouble free operation
 Compatible and interchangeable with most major manufacturers
 Highest quality material available globally
Gear Products Features:
 Heavy duty roller and sleeve bearing designs
 Pressures up to 3500 PSI
 Doweled and high strength cast iron construction
 Wide range of porting, mounting, and shaft options
 Pressure balanced wear plates for high pump efficiency
 Unloader, dry valve, speed sensor and electronic control options
Versa-Pak Refuse
Flow Control/Unloader:
This system allows a preset amount of flow to the
hydraulic system with the excess flow being returned
to tank; this function protects the system’s main relief
valve from being flooded. In addition, the priority type pressure
compensated flow control minimizes heat generation by returning unused oil back to
tank at only a few hundred PSI more than system pressure.
Bushing Series
257 and 360 series
These two are becoming more popular in
the refuse market; bushing units typically
have higher pressure ratings and longer life. Many are
used today on front and rear loaders and also on automated side loader
applications. Typically these are used in unloader applications where
manifolds equipped with solenoids turn the system on and off.
PEK/2100 and
PEL/5151 Series
These two fit a variety of applications in the refuse
industry, designed with both side and rear ports,
SAE-B 2&4 bolt mounting flange, Bi-Rotation and
setup for use as a pump or motor providing versatility for uses in many application.
Commonly seen in refuse roll-off, live floor, small and large rear loaders, recovery
vehicles, container haulers and many other utility type vehicle applications.
CH-640 and CH-512 Series
These two have been specifically designed for
the refuse truck market. The CH Series pumps
are made of high strength cast iron and alloy
steel incorporating Permco’s rugged and dependable
gear pump design. CH pumps are pad mounted with
double 1-1/8 inch drive shafts and large port end cover with
1-1/2 inch NPT inlets and a choice of 3/4 inch or 1 inch O-ring outlets.
Unloading System
The unloading system limits
the flow to the system while
in use to prevent hydraulic
over-speeding. While in the
off mode, the flow is diverted
back to the tank at low pressures to control horsepower
losses.
Remote Mounted
Relief Valves
AZ5514J-100-25 or
AZ5514J-100-32:
Come with 1” NPT ports and is
available with either 2500 or
3200 PSI maximum settings,
and is field adjustable.
Dry
Valve
System
The dry valve system incorporates an
air operated dry valve which permits
hydraulic operation while the vehicle is
in motion, and reduces fuel
consumption during the off mode and
eliminates heat build-up associated
with “live” systems in the on mode.
The 997-01238 can also be incorporated
with either the dry valve or unloading
system to futher protect the
hydraulic system.
16
MOBILE POWER
INDUSTRIAL PUMPS / MOTORS
 Pumps & Motors
For Mobile And Industrial Applications
 Roller Bearing Pumps & Motors
Series:
2100/3000/3100
Gear Width
 Construction Equipment
 Refuse Equipment
 Mining Machinery
 Agricultural Equipment
 Oil Field Equipment
 Industrial Equipment
 Forestry Equipment
* Motor specifications are given @ 1000 RPM and @ 2000 PSI.
** Consult Permco on these gear sizes.
*** 2000 RPM maximum on motors.
# The information shown represents the maximum
# continuous operating conditions.
+ Maximum 3000 RPM for 5151 series.
 Sleeve Bushing Pumps & Motors
Series:
5000/5100/5151
Series:
7500/7600
Series:
P124
Gear Width
Series:
P197 Tandem
MOBILE POWER
PISTON PUMPS / MOTORS
17
 Piston Pumps & Motors
PAVC Series
This hydraulic pump is a Bent-Axis type pump
with fixed displacement, developes under the design
of spherical head pistons. This design is high performance
and extremely efficient. This hydraulic pump is a NEW GENERATION
pump for the Global Auxiliary Power Market. Because of the high torque
requirements, this pump comes with an ISO 7653 DIN mount. All global
PTO manufacturers offer this output option.
PN
Description
5041806
FR 5.5 (20) RIGHT ROTATION, UN THREAD
5041906
FR 5.5 (20) LEFT ROTATION, UN THREAD
5042006
FR 8.4 (30) RIGHT ROTATION, UN THREAD
5042106
FR 8.4 (30) LEFT ROTATION, UN THREAD
5042206
FR 10.4 (40) RIGHT ROTATION, UN THREAD
5042306
FR 10.4 (40) LEFT ROTATION, UN THREAD
5042406
FR 15.8 (60) RIGHT ROTATION, UN THREAD
5042506
FR 15.8 (60) LEFT ROTATION, UN THREAD
5042606
FR 20.8 (80) RIGHT ROTATION, UN THREAD
5042706
FR 20.8 (80) LEFT ROTATION, UN THREAD
5042806
FR 28.9 (110) RIGHT ROTATION, UN THREAD
5042906
FR 28.9 (110) LEFT ROTATION, UN THREAD
XA Series Pumps - 6 Models
Features:
 Flows from 1.1 to 3.84 cu.in. (18 to 65 cc)
 5075 psi (350 bar) continuous working pressure
 5800 psi (400 bar) peak pressure
 maximum speed from 2,300 to 2,900 rpm
 Avialable in S.A.E & DIN
 Change of direction of rotation by simply
 changing a fitting
TXV Pumps - Variable Displacement
These are intelligent pumps! With variable displacement
and pressure-flow control -called Load Sensing, they automatically
regulate to give just what is needed for each movement. Specifically designed
for the needs of the truck hydraulic market, the TXV pumps are particularly
attractive solutions for applications in loading cranes, forestry cranes, refuse
vehicles, salt spreaders and snow and ice equipment, and construction
equipment vehicles. Extremely compact in size to allow direct flange
mounting on engine PTOs or gearbox PTOs, TXV pumps are available
in 7 models from 40cc to 150cc maximum displacement
MA Piston Motors
 Available in displacements from 10cc to 180cc
 MA motors are suitable for all the main fixed
 and mobile applications.
 MA series motors are suitable for intensive
 long duty requirements.
 Designed for both mobile and industrial installations.
 Availible in S.A.E.
variable volume piston pumps
Parker® PAVC and PVP Variable Displacement Piston Pumps are
available in several displacement sizes and have a range of options
to suit your particular application controls for pressure compensation,
load sense, horsepower limiting and load sensing are also available.
Housings are built from high strength cast iron. Sealed bearings,
replaceable port plate, two-piece pump design, as well as many
other features makes the PAVC pump a great choice for operational
cost effectiveness and return on investment (ROI).
Pump Features:
 High strength cast iron housing
 Built-in Supercharger
 High speed capability
 3000 rpm/2600 rpm PAVC100
 Sealed shaft bearing
 Two piece design for east of service
 Cartridge type controls - field changeable
 Replaceable bronze clad port plate
 Air bleed standard for quick priming
 Hydro-dynamic cylinder barrel bearing
 Thru-shaft PAVC100 only
 Full pressure rating on water glycol fluids
 Pump case and shaft seal
 Filter and/or cool drain line - 100 psi maximum
Controls Features:
 Pressure compensated
 Load sensing
 Horsepower - torque limiting
 Horsepower and load sensing
 Remote pressure compensated
 Adjustable maximum volume stop
 Electro-hydraulic pressure
 Electro-hydraulic flow & pressure - Servo control
 Low pressure standby
The PAVC Piston Pumps are ideal for many mobile applications
with operating pressure up to 3000 psi. These compact pumps
feature an integral inlet boost pressure that results in excellent
high self priming speed capability.
PAVC Driven Pump Performance Information
Displacement
Series
33 cc/r
PAVC33
38 cc/r
PAVC38
65 cc/r
PAVC65
100 cc/r
PAVC100
Max. Outlet
Pressure
3000 psi
3000 psi
3000 psi
3000 psi
Rated
Drive Speed
3000 rpm
3000 rpm
3000 rpm
2600 rpm
@ 2000 rpm & 3600 psi
Flow
Input Horsepower
16 gpm
33 hp
18 gpm
36 hp
33 gpm
66 hp
53 gpm
108 hp
18
MOBILE POWER
MOTORS
 Motors
Char-Lynn motors are extremely reliable, compact, and have tremendous power density. They provide a way to meet many needs for
cost-effective power transmission requirements. Multiple motors can be driven by a single power source (pump) and controlled using
a wide array of valves and variable displacement pump controls. Motors can even be configured with electronic sensors to provide
digital feedback for sensing both motor direction and output speed.
Motor options features include:
 Displacement size (cubic inches or cc’s per revolution)
 Output shaft size and type
 Mounting flange type
 Porting interface
 A wide selection of special features such as integrated brakes,
 sensors, integrated cross-over relief valves, 2-speed capability,
 manifold valve packages and environmental protection suited for
 corrosive environments.
H Series
Designed for medium duty applications, the H-Series Motors
use industry-proven spool valve technology, combined with
state-of-the-art gerotors. In addition, a wide variety of mounting
flanges, shafts, ports and valving options provide design
flexibility. Direction of shaft rotation and shaft speed can be
controlled easily and smoothly throughout the speed range
of the motor, and equipment can be driven direct, eliminating
costly mechanical components.
Features:
 High efficiency
 Powerful compact package
 Design flexibility
 Extended, leak-free performance
H Series
S Series
2000 Series
S Series
2000 Series
The popular Char-Lynn 2000 Series Disc Valve Hydraulic
Motors provide torque up to 7500 lb-in. This proven
design is reliable and durable. Eaton has added options
that make the motor more flexible to use in a wide variety
of applications. The integral cross-over relief valve is the
latest innovation in the 2000 series motors.
Features:
 Three zone design for longer life and true
 bi-directionality
 Bearings that meet the highest standards of
 the industry
 Options to optimize performance in every application
 Integrated cross-over relief valve option
The new improved Char-Lynn S Series Motors with optimized
Geroler geometry offers enhanced performance with reduced
drive-running angle, while retaining the overall package
size of the original S series. Design improvements include
upgraded steel end cap, O-Ring section seals and optimized
Geroler set.
The Geroler set has precision-machined rollers in the outer
ring which provide support with rolling contact between the
star and ring. This improves mechanical efficiency,
especially at start-up and at low speed conditions.
Improvements incorporated into the latest S Series motor
provide reliable leak-free performance and smooth
operation at start-up conditions.
Features:
 Constant clearance Geroler design
 Three moving components (gerotor, drive, shaft)
 Optimized drive running angle
 Three-zone pressure design (inlet, return and case)
 Variety of displacements, shafts and mounts
The Parker line of Low Speed High Torque (LSHT) motors provide power and versatility at an affordable cost.
Available in small, medium, and large frame models, we have you covered for most hydraulic motor application
requirements.
Small Frame LSHT Motor - TB Series
Small Frame
Accessories:
Specifications:
This light to medium duty motor incorporates all the features of heavy duty motors.
Design features include
a high pressure shaft seal so external
drains are never required. Also features
roller vane technology for automatic wear
compensation, and full flow internal cooling
and flushing. This is a very economical
motor for most light to
medium duty applications.
 Speed Sensor
 Hot Oil Shuttle
 Crossover Relief Valve
 Internal Relief Valve
 Multiple Disc Brake
Small Frame LSHT Motor - TE Series
This medium duty motor has higher pressure ratings than the TB motor,
for applications requiring higher torque.
Robust roller bearings withstand higher
side loads and are suitable for chain and
sprocket shaft connections. It uses high
pressure shaft seals, robust
roller bearings, and high flow shaft
seal cooling.
 14 Displ. 45 - 390 cm3/rev (2.5 - 24.0 in3/rev)
 Max. Control Pressure - 125 bar - to 1800 psi
 Max. Inter. Pressure - 165 bar - to 2400 psi
 Max. Oil Flow - 57 lpm - to 15 gpm
 Max. Speed - 785 rpm
 Max Cont. Torque - 440 Nm - 3897 lb. in.
 Max. Inter. Torque - 540 Nm - 4783 lb. in.
 Max Side Load - 4900 Nm - to 1100 lb.
Specifications:
 14 Displ. 45 - 390 cm3/rev (2.5 - 24.0 in3/rev)
 Max. Control Pressure - 140 bar - to 2030 psi
 Max. Inter. Pressure - 190 bar - to 2750 psi
 Max. Oil Flow - 75 lpm - to 20 gpm
 Max. Speed - 1000 rpm
 Max Cont. Torque - 467 Nm - 4139 lb. in.
 Max. Inter. Torque - 648 Nm - 5728 lb. in.
 Max Side Load - 6650 Nm - to 1500 lb.
Large Frame LSHT Motor - TG Series
The heart of Parker’s TG Series powertrain, the torque link, is an
extra heavy duty part that includes patented 60:40 spline geometry.
Rugged construction throughout allows the transmission of over 13,000
lb inches of torque. The entire powertrain is continually washed in cool,
high flow fluid to assure long life. Roller vanes and sealed commutator
maintain high efficiency and provide smooth low speed performance.
Specifications:
 12 Displ. 140 - 958 cm3/rev (8.6 - 58.5 in3/rev)
 Max. Control Pressure - 210 bar - to 3000 psi
 Max. Inter. Pressure - 281 bar - to 4000 psi
 Max. Oil Flow - 114 lpm - to 30 gpm
 Max. Speed - 660 rpm
 Max Cont. Torque - 1044 Nm - 9239 lb. in.
 Max. Inter. Torque - 1428 Nm - 12636 lb. in.
 Max Side Load - 16000 Nm - to 3597 lb.
MOBILE POWER
BLOWERS / PUMPS / COMPRESSORS
 Blowers
The P857 is a two
lobe, positive
displacement
blower design
Features:
 Product Pumps
Features:
 Coated inner wear sleeves for leak prevention due to
 anti-corrosive material
 Easy to remove for maintenance or repair
 Simplified assembly and easier profile setting
 Specially designed for a hydraulic adapter
 Twin drive shafts allow for universal bi-directional mounting
 Complete cast iron body and side plates
 Rotor profile with constant gap
 Internal breather reduces water contamination of the oil
 Durable taper lock guarantees easy assembly
 Compressors
P40 Oil Lubricated
Piston Compressor (P40)
 Dependable sliding vane action provides
 low maintenance, quiet operation, and
 long lasting performance
 Relief valve can be adjusted to
 safeguard the pump from over pressure
 Optional strainers to protect the pump
 from any foreign material moving through
 the tank or piping
 Dual shaft for clock/counter clockwise drives
Features:
 Unique sliding-vane pump design self
 adjusts for wear to maintain flow rates
 Excellent self-priming and dry run capabilities
 Dual end shaft on 2,” 2.5” and 3” models simplifies installation
 Blackmer mechanical seal and ball bearing construction provide
 maximum reliability
 Symmetrical bearing support assures even loading and wear
 for longer life
 Adjustable relief valve protects pump against excessive pressures
 External ball bearings are isolated from pumpage by mechanical
 seals to maximize bearing life and minimize contamination risk
 Easy maintenance: vanes can be easily replaced without
 removing pump from truck
Features:
 30% more air than equivalent
 sized machines
 The P40 is a high performance piston
 compressor designed for the tank truck market
 The narrow profile makes fitting inside truck
 frame rails fast and simple
 One of the lightest oil lubricated machines
 in it’s class
 Quiet operation due to heavy duty construction
 High airflow helps build tank pressure
V120 Oil Free Vane
Compressor (SV120)
Features:
 Ranger Pumps, Inc. manufactures a precision built 
 helical gear pump for industrial applications.
 The capacity range is available
 from 25 GPM to 360 GPM and pressures
 to 125 PSI.
 Ranger Pumps are designed to use as
 low speed pumps for both low and high
 viscosity liquids.
 Ranger Pumps & all parts are directly
 interchangeable with Roper® Pumps & Parts.
Roper® is a registered trademark of Roper Holdings, Inc.
Ranger, Inc. is not affiliated with Roper Pump Company
Features:
 Highest air flow in it’s class
 The SV120 is designed for
 today’s tank truck market
 High air flow mean faster turnaround,
 and more load per month
 “Drop-in” design, no need to change
 existing pipe work
 Quiet operation
 Full range of accessories available
19
Features:
 Available for 3648, 3748 & 3848
 Intergral Bi-Directional Relief Valve
 Same performance as our proven 3600 Series
 Direction relief valves
 Easy-to-maintain design
 Torture tested
 Life exceeded 12,000 fully reversed cycles
Not all products available at all Branch locations.
20
MOBILE POWER
VACUUM PUMPS / COOLERS
 Vacuum Pumps
FleetPride carries the leading manufacturers in the vacuum pump and oil cooler lines.
Rotary Vane Vacuum Pump
RCF500 Rotary Vane Vacuum
Pump Fruitland’s 500 Series
pumps are the most widely l
used throughout the industry.
The 500 series pumps use
less oil than any other
rotary vane pump in
the industry.
HXL Series II
Vacuum/Pressure Pumps
Pump Features:
 Achieve minimum 27” Hg (Intermittent)
 Precise machining and sssembly
 Heavy duty bearings
 Viton oil deals for longer dervice life
 Kevlar vanes are heat dtablilized and
 machined with exacting tolerances for
 superior ruggedness and durability
 Easy to service
 Superior pump life
Our Challenger Series pumps are designed and built with the
customer in mind resulting in dependable, high performing pumps that
are easy to install, operate and service. As the only industrial grade
rotary vane vacuum pump designed, built and supported in the USA
we are committed to also being the best pump period.
Superior cooling for extended operations
in severe conditions:
 Proven crash protection allowing all major components
 to survive a catastrophic failure
 Oversize heavy duty roller bearings
 ensures more drive options
 Precision pinned end plates for
 exact reassembly alignment
 High strength castings poured in the USA
 High temp Teflon oil lines allow
 for visual oil flow inspection
 Remote mount 5 quart clear
 oil tank for consistant oil level monitoring
 Four point automatic lubrication system
 Liquid or fan cooled versions of each model
Not all products available at all Branch locations.
 Hydraulic Oil Coolers
Frame Mounted Cooling
HydraFLOW™ is designed and assembled as a
complete, easy to install package featuring:
 ProveMaximum efficiency from hydraulic fan system
 Minimize filter damage with filter bypass valve
 Preventable oil spillage with quick, top mounted filter
 Hidden breather reduces water contamination
 Radiator bypass valve and cartridge style relief valve
 Large sight glass
SS 675 Behind-Cab Unit
The SS675 behind-cab unit is mounted behind the
cab and across the frame rails, keeping the unit
completely free from road debris. This unit is a
powerhouse, boasting twice the capacity of our
frame mount models. This allows you to drive higher
horsepower applications like bulk feed trailers,
VAC pumps and pneumatic blowers.
SS675 Features:
 Strong Design: Stainless steel construction ensures
great looks and long life. Unlike steel units, does not rust and
is easily shined to keep your trucks looking top-of-the-line.
 Heavy Duty: Our most powerful model, suitable for the
toughest and most demanding mobile hydraulic applications.
 “No-Drill” Optional Mounting Kit: Instead of drilling
into the frame rails, mount your unit instead with an optional set
of clips. Just as strong as drilling, these clips make the unit
easier and faster to install and don’t compromise the integrity of
your frame.
Additional electric and hydraulic models available, ask for details.
Not all products available at all Branch locations.
MISCELLANEOUS 21
 Line Filters
 Temperature Controls
Filter Assemblies & Filter Carts
RoadWatch® uses the same state-of-the-art infrared sensing
technology employed in heat-seeking missiles to constantly
measure and report actual road surface temperatures.
RoadWatch will accurately sense a 1° change in road surface
temperature in one-tenth of a second. And, the early warning
system alerts the driver when the road surface temperature
dips to 37° or below. Using state-of-the-art infrared sensing,
RoadWatch was originally developed to assist highway and
public works departments in determining when and where to
apply road treatment chemicals. Thousands of RoadWatch
systems are already in use throughout North America.
Using its unique early warning capabilities, city and state
highway departments and airports, rely on RoadWatch to
tell them when to treat road surfaces before hazardous
driving conditions appear.
RoadWatch® DC-1
We carry a complete line of
filter carts and filters that
feature easy-to-read filter
condition indicators that help
reduce the possibility of
contamination in hydraulic
systems. Spin-off throw-away
elements make replacements
fast and easy. Filters are a
vailable in external or
tank-mounted models.
 Valves & Fittings
Complete lines of all
fittings and quick
disconnects and
hydraulic hose fittings
in stock and
special order
is available.
Infrared deployment control scans
the road surface temperature, then
automatically disperses de-icing and
granular/pre-wet traction agents.
The DC-1 is designed to be
connected to existing electronic
spreader controls. Three output
channels control 3 spreader
functions. Each channel has
programmable temperature limits.
Accessories:
 12 volt quick connect power cables
 Suction cup window mount
 Sensor mounting brackets for frame, behind sleeper, and large tubes
 Mini C mount for trucks or cars
 Display mounting bracket or pedestal
 Mirror display mounting or sensor mounting available
 Clutch Pump Service Parts
 Test Equipment
Wide
variety
available.
Complete line of clutch pump parts and accessories available.
BR549
Clutch Pump Bracket
for 2 bolt “A” mount
999-00956
Clutch Pump
Switch Kit
*After burnishing, see Owner’s Manual.
512010
AA Groove
Clutch 120 lb. ft.*
520226
6 Groove Type K
Serpentine Clutch 120 lb. ft.*
515376
8 Groove Type K
Serpentine Clutch 120 lb. ft.*
 Tail Gate Cylinders
Full line of
4, 6, and 8 inch
stroke tail gate
cylinders
available.
Call for details.
22
MOBILE POWER
CONSOLES / CONTROLS
 Consoles/Hoist/PTO Controls
VPHPV
The Apsco engineering team seeks to consistently
deliver an outstanding product of unsurpassed quality
and performance. Custom consoles designed to your
specifications are available. Not only can Apsco put
any valve or switch in the console, but they can also
add your own company’s logo.
 Dump Pump Air Actuator
Features:
 Simple installation
 Compact - no exposed moving parts
 Cost effective
 Problem free!
VPAS-1
Hoist And PTO Control
This hoist and PTO control in one unit is
available with console and manual PTO kick out.
Console with tail gate valve is also available.
Retro Fits:
Hydraulic pump/valve combinations, commercial, Permco,
Muncie, Apsco’s patented self centering design.
 Direct Mount Cylinders
Features:
 1 piece
 Easy installation
 No subassembly required
 No exposed moving parts
 Proportional control
 Cycle tested - over 1 million cycles
 Revolutionary anti-bind technology (patent pending)
 Custom designed to fit most
 most major hydraulic valves
C-3800-DM
VPHVC-TC-8/13
VTS-1 & VTS-2
VTS-1 is a spring to neutral 3-position
VTS-2 is a 2-position, 4-way valve
 Lift Axle Accessories
4446
All in one filter,
regulator
and lubricator
 Pneumatic Actuators
VE-2
Electric over air, 4-way,
2 position solenoid valve
Features:
 2.5” to 8” bore, steel, aluminum or composite tubing
 Available bearing supports maximize piston rod durability
 High tensile steel rods - plated for corrosion resistance
 Low temperature seals
 Rod wipers standard for contaminant resistance
 Available in any practical stroke
 Standard sizes available or custom made to specifications
 Tail Gate Lock Kit
Features:
 2 1/2” and 3 1/2” bore
 6” and 8” stroke
 Electric and
 over air available
VL-5-ES
Electric or manual
5/2 function, 4-way
valve
VX-4
Push-Pull, 2 position valve,
5/2 function, 4-way valve
function, 1/4” NPT ports, CV = 1.5
Adjustable Pressure Regulator
13 SCFM @ 100 PSIG,
rated pressure range.
1 to 125 PSIG, compact design,
1/4” ports.
V-44-AP-SR
Air pilot spring return valve,
5/2 function, 4-way valve
function, 1/4” ports.
CONSOLES / CONTROLS 23
MOBILE POWER
 Consoles & Stackable Valves - vm series
Custom Swivel Pedestals
These valves control pneumatic or hydraulic directional control
valves on industrial equipment from a remote location. Flexibility of
the system with the use of bent handles allows for the customization
of consoles for ideal mounting requirements and ease of operation.
Their compact size makes them well suited for today’s mobile
equipment, while common inlet and exhaust ports simplify plumbing
when assembled in banks.
For Use With VM Air Control Valve
 1 - 100 Proportional control
 Ability to stack valves into multiple
 banked packages
 Various handle bends for flexible installation
Handles Available In
Straight or Angled
20° - 35° - 45° - 55°
VM-8
Neutral detent
Features:
VM7-2B2020
 Easier installation
 Patented swivel lock design
 Durable powder coating
VM-9
VM-7
3 position detent
VM-11
1 off center detent
Features:
 13” console available for up to three bank valves
 1-100 proportional control
 Ability to stack valves into multiple banked packages
 Various handle bends for installation flexibility
 Straight, 20°, 35°, 45° or 55° handles available
VM-7
VM-10
2 bank with console
Quad position valve
 Gear Pumps & Motors
 Directional Control Valves
Series 40
Series 50
Rated to 3000 psi. Spline or keyed shafts,
Series 60
side or rear porting, dual rotation available
on standard models. Pressure balanced
loading plates on either side of gears for
Series 53
maximum efficiency.
Series 40 - SAE A - 2 bolt mount - rated to 17.5 gpm
6 sizes: .5 - .75 - 1.00 - 1.25 - 1.50 and 1.80 in3/rev
Series 50 - SAE B - 2 bolt mount - rated to 44 gpm
7 sizes: 1.52 - 1.95 - 2.32 - 2.74 - 3.30 - 3.80 and 5.20 in3/rev
Series 60 - SAE C mount - rated to 90 gpm
6 sizes: 4.05 - 5.15 - 6.15 - 7.15 - 8.15 and 9.25 in3/rev
Series 53 - SAE B mount - displacements same as Series 50. Dual tandem body
pump in single rotation only. Operates as 2 separate sections, combined sections or
w/common inlet, and 2 outlets supply flow to 2 separate systems.
Series 50G - SAE C mount - planetary gear
reducer for high torque at low speeds. 4 bolt
mount w/spline or keyed ouput shafts and
tapered roller bearings for thrust/side load.
5.33 to 1 gearbox reduction.
Series 50G
Series 50PGR
Series 50T
5 BANK
Series 50PGR - SAE B mount - 2 bolt
input mount with 7/8” spline, 13 tooth and
16/32 pitch female input spline for use with
50M or equivalent motor. 5.33 to 1 ratio.
Series 50T - 3.1 step up from 540 rpm
splined PTO shaft. Thru-type 6 tooth internal
PTO shaft for operating. PTO driven attachment with pump in operation. Available in
effective displacements. 21 tooth also
available for 1000 rpm PTO.
Model SS - up to 9 gpm - 3000 psi - ductile iron body.
Series operation, single or multi-function unit operation.
Excellent spool metering, low
leakage, manual and float detents.
Model AD - 15 gpm - 3000 psi - 1 or 2
Model SS
spool model w/integral relief and load
checks. Excellent metering, low leakage.
Variety of spool and actuator options.
Power beyond/closed center available.
Model BA - 30 gpm - 2500 psi - 1, 2 or 3
spool valve w/excellent metering, integral
differential poppet type relief and load
checks. Variety of spool types/actuator
options. Power beyond/closed center available.
Model AD
Model BA
Model BC - Single spool, manually adjustable, built-in pressure compensated
priority type flow control. Character/options similar to BA - open center only.
C Series - CA - Manual - spring centered. CD - automatic pressure kickout.
CS - solenoid operated version.
Converta - Single spool standard model, open center only.
Simple field conversion from 4-way to 3-way, and spring centered
to manual detent.
Converta
Model VS2 - 20 gpm - 3000 psi
Model
3 ported diverts flow to either of
2 separate circuits.
Model VS4 - 40 gpm - 3000 psi
Model BC
3 ported diverts flow to either of
2 separate circuits. Handle, knob,
Model CA
detents, spring centering, and solenoid
options available.
Model SD4 - 40 gpm - 3000 psi
6 ported diverts flow to either of
Model VS
2 separate circuits using a single control
valve. Handle, knob, detents, spring centerModel SD
ing, and solenoid options available.
24
MOBILE POWER
CABLE CONTROLS
 Custom Cable Controls
We can custom build just about any cable for automotive,
heavy duty, agricultural, and industrial applications.
 Button Lock
 Push-Pull Standard
Depressing the center button allows pushing or pulling the knob to make course
travel adjustments. Routing of the flexible cable allows installation options that
are not possible with solid linkages. Various output configurations are available
to suit a specific application. The ordering code and technical descriptions show
available choices.
Features:
 Push-Pull Standard industrial control cable assemblies
 Shift, Brake, Clutch & Adjustable Control Cables
 Locking & Non-Locking Control Cables
 Wide temperature range from -65° F to +230° F
 Low Friction & Low Friction EXT - Green,
 Utility - Gray, Bristow - Black
 Constructed of tough, durable materials
 Long lasting seals
 Environmentally protected
Features:
 Stainless steel or plated carbon steel
 Plastic coated carbon steel conduit and inner member
 Plastic seal & knob
 Suggested end fittings - full range
 Micro Adjust Push-Pull Control Head
Cablecraft Ordering Codes
XXX
C
553 = Standard
554 = Wire
Output Options
T = Threaded
G = Grooved
Cable Length
End Fittings
Applications:
 Load - 20 lb. maximum
 Travel - 3.00” maximum
 Threaded mount, friction lock, and disconnect
 Normal vibration does not affect the micro adjust setting
 Optional friction lock accessory available for excessive vibration
 Various disconnect and output end configurations are available
C = Conduit Cap - available only on solid wire & wire rope I/M
All line art dimensions are represented in inches.
 Cable Hardware Parts & Accessories
Spring Return Kit:
Convert any LD size travel threaded swivel end to spring loaded with this kit.
Complete line of cable hardware parts & accessories available.
Knobs & Handles:
Wide variety from PTO,
and mushroom, to aluminum
and twist lock available.
T
I/M Type
The Micro Adjust control heads are ideal for remote operation of a throttle, regulating
valve, or other applications needing precise adjustment capabilities. Depressing the
center button allows pushing or pulling the knob to make course travel adjustments.
A flexible dust seal protects the internal release mechanism. Rotating the knob clockwise extends the output in the finite mode, and
counter-clockwise retracts.
Clevis Assemblies: Includes pin
washer and cotter pin.
Wide selection available.
565-553
Hydroback: Self centering in a variety of sizes.
Slip Clevis:
P/N: AC310
Quick Disconnect
Ball Joint Connectors:
Wide variety of sizes
and part numbers
for all of your needs.
Rod End
Bearings:
Assorted sizes.
Female Threaded
Eye Ends:
Assorted sizes.
Strap Clamps
And Shims:
VLD & LD.
Wire Stop
& Pivot:
Assorted sizes.
End Rod Thread
Adapters:
Assorted sizes.
 Wescon Remote Control Systems
Look to Wescon for your remote valve applications.
Wescon’s remote valve control ‘RVC’ has been engineered
to place versatility in the hands of the installer. Our center
end-locking feature is thumb activated by the “Big Red Button,”
and can help your system meet OSHA standards. We also offer
options such as bent levers to fit your mounting requirements,
electric switches installed in the lever, or an adjustable friction
device to “customize” your lever resistance. We offer a wide
selection of control heads, conduit, connection hardware kits,
and mounting systems, making it easy to choose Wescon
for your RVC applications.
Wescon’s push-pull cable assemblies are
available in either groove or bulkhead
configurations. Also upon request,
Wescon offers a bulkhead/groove
combination.
MOBILE POWER
CONTROLLERS 25
 Spreader Control Systems
Parker Spread Master Systems are designed to provide reliable application of salt and sand with
remote electronics and a safer quieter cab environment.The electronics provide remote proportional
control of the Feed Rate and Spinner for your V-Box or Tailgate Spreader.
PSM-1500-1
Single knob
spreader control
with an on/off
switch.
PSM-1500-2
Dual knob spreader control
with an on/off switch.
PSM-1000
Dual knob controller
with a blast function
and an on/off switch.
This unit removes the
hydraulic from within the cab,
giving you a safer and quieter
environment to work in.
The Parker Solution:
Complete Systems from Parker remove hydraulics
from the cab with remote compact electronics and
easy to operate controls
Superior Performance:
n Total System Reliability
n Safer/Quieter Environment
n Improved Cab Ergonomics
n Operator Friendly
Systems Features:
n Feed Rate Proportional Cartridge
n 16 gpm
n Spinner Proportional Cartridge 7gpm
n Manual Overrides
n Fixed Displacement Pumps
n System Safety Relief in Open Center
n Systems (PSM-1000 only)
n Standard SAE Ports
n 3000 psi Operation
n Load Sense System Capability with PSM-1000
 QDB Series
Flow Controls are designed for applications such as spreaders where
precise control of one or two functions may be required without regard
to variations in load pressure. These valves are used mainly on snow
removal equipment, but can also be used for other applications such
as sand and fertilizer.
Features:
n Hardened and precision ground parts for durability
n Easy to adjust knobs
n Adjustable flow ranges for varying applications
n Load sense option
n Manual bypass option
n Solenoid bypass option
n Anodized aluminum body for long life
DICKEY-john® Control Point® control is a resourceful three
channel system that provides you the power to control granular
and liquid material application rates, spinner speed, and spread
width. This user-friendly unit includes an automatic override that
takes control after technical failure, and in the event of ground
speed sensor malfunction, the built-in ground speed simulator lets
you keep spreading — even when your vehicle is stationary.
LT Control™ application controller delivers precision control when
you need it most. This versatile, open-loop system operates in
automatic, manual, or spot spreading modes under even the
harshest weather conditions.
LT Control™
26
WET LINE SYSTEM PRODUCTS
MOBILE POWER
 Wet Line Systems
FleetPride is your premier supplier for any type of Wet Line kit.We can supply the complete wet kit, or simply the
main components such as Power Take-Off Units, Pumps, Control Valves, Filters, Reservoirs (Tanks), and/or
Hydraulic Hoses and Fittings. Whatever fits your needs, we are here to help with expert advice, service and quality
brand components from these manufacturers: VantagePower,Parker, Chelsea, Commercial, Permco,
Apsco, Muncie, and many more!
VantagePower dual pressure pump is designed to operate
a dump trailer and a live floor which require 2 different
operating pressures:
n Dual Pressure Relief: low for dump bodies, high for live floors.
n Easy to switch from low to high pressure using truck air
n Large 1 ½” NPT suction port in the gear housing
n Three line system for continuous duty
n Field adjustable relief settings
n Dowelled construction
n Factory installed “OEM” air shift with full metering
n capabilities
n Direct mount SAE “B” 4 bolt or twin shafted remote mount
n with bracket
n Relief valve protects the high pressure portion of the system
n as well as the pump
n 37 GPM @ 1800 RPM 100% factory tested
n 2 year warranty
 Three Way Combo Kit System
Our 3-Way Combo Kit System allows you to operate multiple
trailers with one tractor hydraulic system. This provides the
fleet owner with greater flexibility to use one tractor
for multiple purposes:
 Hydraulic Reservoirs
Steel & Aluminum:
For continuous duty applications where high
oil temperatures may be encountered.
Upright reservoirs of 50 and 70 gallon capacities
made from steel or aluminum is ideal for wet line
systems for moving floor trailers, as well as
traditional dump applications. Versions of the
55 and 75 gallons side frame mount are available.
For smaller reservoir requirements, 15, 25, and
35 gallon reservoirs designed with side mount
capabilities are available.
Polyethylene reservoirs:
Polyethylene reservoirs are constructed of
rotational molding technologies. The reservoirs are
available in four configurations: 50 and 75 gallon for
upright and 35 and 50 gallon for side mount.
PN: 1300-1 or 1300-3
3-Way Combo Kit system is designed to operate:
n End Dump Trailers
n Side Dump Trailers * n Walking Floor Trailers
n Low Boys (1300-3 Kit)
n Provides Dual pressure connections for 2000 PSI End Dumps,
n or 2800 PSI trailers
n VantagePower high pressure dump pumps provide high
n pressure capability to 2800 PSI, along with 1”- 15 spline
PN
Description
n output shaft for long pump life
n Unique hose connections make misconnecting trailers to
VPCKDP20-3LAS25-BB
CCW ROTATION - BB SPLINE
n incorrect ports more difficult. This results in safer operation,
VPCKDP20-3RAS25-BB
CW ROTATION - BB SPLINE
n reduces the possibility of End Dump cylinder separations from
n over pressurizing telescopic cylinders
HP Dump Pump 5.1 in. - ORB Ports,
n Hose connections clearly marked on Coupler Mounting Bar
2.5-3K Relief with air shifter
n Operator controls all trailer functions from inside the cab
Note: Cab air controls selected separately
n with air controls
get the ad-vantage today!
®
VP PN
Pneumatic Air Controls Description
VPHPV
HOIST - PTO VALVE
VPHPVC-8
VALVE W/ 8” CONSOLE
VPHPVC-T-8
VALVE W/ 8” CONSOLE & TUBING
VPHPVC-13
VALVE W/ 13” CONSOLE
VPHPVC-Y-13
VALVE W/ 13” CONSOLE & TUBING
VPHPVC-M-Y-13
VALVE W/ 13” CONSOLE & TUBING - NO KICKOUT
VPHPVC-TG-8
VALVE, HOIST, PTO, TAILGATE 8” CONSOLE
VPHPVC-TG-13
VALVE, HOIST, PTO, TAILGATE 13” CONSOLE
VPHPVC-HP-13
VALVE, HOIST, PTO, HIGH PRESSURE 13” CONSOLE
VPHV
HOIST VALVE
hydraulic gear pumps:
Pneumatic air controls:
VantagePower offers a complete line of pneumatic controls and
pneumatic cylinders for hydraulic valves as well as, stackable
feathering controls to operate the valves including pedestals,
consoles, and tubing kits. Whether you need standard or custom
designed controls, VantagePower can provide you with what
you need.
VantagePower offers a complete line of pumps from 3 gpm to 40 gpm. Made of cast iron construction, precision roller bearings,
low friction bushings, wide range of mounting options, and porting. Pumps and motors are available as single or multiple units.
VP PN
®
Hydraulic Gear Pumps Description
P20 SERIES
P20A396JEAF12-65
7/8 - 13 spline side & rear port s.a.e.
P20A327JEAF15-65
7/8 - 13 spline side & rear port s.a.e.
P20A396JEAL17-65
7/8 - 13 spline side & rear port s.a.e.
P20A346JEAL20-25
7/8 - 13 spline side & rear port s.a.e.
P51A346YRYL17-65
7/8 - 13 spline side & rear port N.P.T.
P51 SERIES
P51A346YRYL20-65
7/8 - 13 spline side & rear port N.P.T.
P51A346YRYR22-65
7/8 - 13 spline side & rear port N.P.T.
P51A346YRYR25-65
7/8 - 13 spline side & rear port N.P.T.
P51 SERIES WITH RELIEF
P51A346YRYL17-65RV
7/8 - 13 spline with built in relief
P51A346YRYR22-65RV
7/8 - 13 spline with built in relief
DUMP PUMPS:
VP PN
VPC-101-25-Z-MS-25
Dump Pumps Description
Remote mount twin shaft
VPC-102-25-Z-L-MS-25
DIRECT MOUNT LH
VPC-102-25-Z-L-AS-25
DIRECT MOUNT LH with air shift
VPC-102-25-Z-R-MS-25
DIRECT MOUNT RH
RESERVOIRS:
VantagePower offers a complete line of reservoirs from 7 to 75 gallon capacity. All are heavily constructed out of aluminum, steel, or poly materials.
VP PN
Reservoir Description
Aluminum
50-A-UR-O
50 GALLON upright aluminum
50-A-SM-O
50 GALLON SADDLEMOUNT aluminum
70-A-UR-O
70 GALLON upright aluminum
Steel
50-S-SM-O
50 GALLON SADDLE MOUNT STEEL
50-S-UR-O
50 GALLON upright Steel
75-S-SM-O
75 GALLON SADDLEMOUNT STEEL
27
®
MobilePower
Contact your local FleetPride location or FleetPride Mobile Power
toll free at 888-338-5352 or fax 203-287-3720 for availability and technical support.
HYDRAULIC
COMPONENTS
V3-1.2014
www.fleetpride.com
`