Document 402867

DO GUIDE
DO Check the Box
QTY PRODUCT
1
DM-TX-201-C
DigitalMedia 8G+TM Transmitter 201
PART NUM.
Power Pack, 24 Vdc 0.75 A, 100-240 Vac
DO Mount the DM-TX-201-C
DO Make Connections to the DM-TX-201-C
Mount the DM-TX-201-C onto a flat surface or rack rail as
appropriate for the installation.
Make connections to the DM-TX-201-C as required for the
application.
Mounting onto a Flat Surface
USB HID: Connect to the USB host interface of a computer
or other USB HID-compliant host device (USB cable not
included).
Using four mounting screws (not included), mount the
DM-TX-201-C onto a flat surface such as a wall or a ceiling.
2037209
Not Included: Cables, Rack Mount Screws, and Surface Mount Screws
NOTE: The DM OUT port is a PoDM (Power over DM) and PoH
(Power over HDBaseT) PD (Powered Device) port. To receive
PoDM or PoH, the DM-TX-201-C requires a connection to a
DigitalMedia switcher or other equipment that has a PoDM or
PoH PSE (Power Sourcing Equipment) port. Any wiring that is
connected to a PoDM or PoH PSE port is for intra-building use
only and should not be connected to a line that runs outside of
the building in which the PSE is located.
HDMI IN: Connect to an HDMI® audio/video source (HDMI
cable not included).
AUDIO IN: Connect to an unbalanced audio source
(unbalanced 3.5 mm TRS mini phone jack cable not included).
NOTE: The maximum cable length is 330 feet (100 meters)
using DM-CBL-8G, DM-CBL, DM-CBL-D, or third-party
CAT5e (or better) cable. Shielded cable and connectors
are recommended to safeguard against unpredictable
environmental electrical noise that may impact performance at
resolutions above 1080p.
LAN: Connect to a local network device (Ethernet cable not
included).
HDMI OUT: Connect to the receiving device (HDMI cable not
included).
DM OUT: Connect to the DM 8G+™ input of a DigitalMedia™
switcher, a DigitalMedia 8G+™ receiver, or another DigitalMedia
device, or connect to an HDBaseT® device (Crestron®
DM-CBL-8G, DM-CBL, DM-CBL-D, or third-party CAT5e
[or better] UTP or STP cables not included).
PWR 24 VDC 0.75A: (Make this connection only if the
DM-TX-201-C is not to be powered using PoDM or PoH.)
Connect to the included power pack.
RGB IN: Connect to an RGB (VGA) or component (YPbPr)
video source (VGA cable not included).
(Ground): Connect to earth ground (building steel).
LAPTOP
Mounting onto a Rack Rail
USB
MOUSE AND
KEYBOARD
Using two mounting screws (not included), mount the left or
right mounting flange of the DM-TX-201-C onto the front or rear
rail of a rack.
BLU-RAY
TM
DIO
AU
P
TU
SE
B
RG
IN
MI
HD
DM-TX-201-C
D
B HI
US
C
1- TER
20
N
XCE
-T
DM TER
U
MP
DM
CO
R
PW C
VD
24 75A
0.
MI
HD
DM
T
SE
RE
OUT
POWER PACK
(Not Required
if Using
PoDM or PoH)
OUT
N
LA
DIOR
+
AU
+
VI
C-D
6
MP
/CO
DM
DM
OUT
1
-M
POE
DM
IO
D8
X8
I-I
DV
1
24
DIOR
+
+
- G
24
VI
C-D
DM
24
IN
IO
24
IA
L MED
M
I OUT
N
AB
G
G
HID
DM
OUT
ON
TR
EI
G
EI
G
EI
G
24
24
IN
OU
MI
HD
AB
G
AB
G
AB
G
AB
G
S
UT
TP
1
DM
4
3
2
k
Uplin
7
OUT
EI
G
EI
G
4
ID-C-C
DM
C-V
DM
-5
POE
-SWCEN
8
EI
G
EI
G
POE
DM
OUT
IN
ER
FIB UT
INP
OUT
II OUT
HDM
HDM
ON
TR
ES
CR
IO
OUT
D
ON
TR
ES
CR
2
.0A
V~4
-2500 Hz
10050/6
E-5
C
48VD
er
Pow
-PO
-SW
R
IBE
M
C-F
DM
I OUT
HDM
AUD
1
ON h
TR Switc
ES Ethernet
CRPower over
AUD
ES
24
24
DM
OUT
1
USB
I IN
HDM
LA
G
EI
POE
IO
AUD
I OUT
HDM
HDM
G
AB
ITA
DIG
D
HDM
2
3
4
AB
OUT
AUD
I OUT
G
AB
4
IN
CR
S
UT
OU
DM
AU
L
B HID
US
I OUT
HDM
DM
HD
TP
3
IO
IN
ITE
POS IN3
COM POE
2
HDM
A
RC
ID-
C-V
Y
I OUT
4
L
DM
Pb/Y
ON
TR
ES
CR
IN
OUT
MI
IN
OUT
OUT
AUD
IA
L MED
M
ITA
DIG
D
2
F
SPI
Pr/C
HDM
IN
OUT
POE
MI
HD
PoE
IO
AUD R
IN
IN
DM
IN
I-I
DV
I OUT
POE
DM
POE
5
- G
L
B HID
US
CEN
MONITOR
LAPTOP
DO Set the IP Address
By default, DHCP (Dynamic Host Configuration Protocol) is enabled. If desired, you can assign
the default IP address to a DM-TX-201-C that connects to a DigitalMedia receiver. To do so, hold
down the SETUP button while the unit boots up. The default IP address, which is 192.168.1.236,
overwrites the current setting. To manually set a different IP address, use Crestron Toolbox™.
NOTE: If the DM-TX-201-C connects to a DigitalMedia switcher, the DM-TX-201-C is configured
by the switcher automatically. As a result, setup of the IP address is not required.
DO Learn More
Check the website for the latest firmware updates.
Crestron Electronics 15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
As of the date of manufacture, the product has been tested and found to comply with specifications for
CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
DO GUIDE
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•• Reorient or relocate the receiving antenna
•• Increase the separation between the equipment and receiver
•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specific patents that cover Crestron products are listed at www.patents.crestron.com.
Product warranty can be found at www.crestron.com/warranty.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G+, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States
and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and
the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may
be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron
is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.
DOC. 7719A (2042532) 10.14
Specifications subject to change without notice.
`