MATERIAL SAFETY DATA SHEET For 1Shot/Chromatic Liquid Coatings and Associated Liquid Materials

MATERIAL SAFETY DATA SHEET
For 1Shot/Chromatic Liquid Coatings and Associated Liquid Materials
One Shot, LLC
A Spraylat Company
5300 W. 5th Avenue
Gary, IN 46406
(219) 949-1684
Fax: (219) 949-1612
e-mail [email protected]
PREPARED BY: Health, Safety and Environmental Coordinator
EMERGENCY PHONE:
INTERNATIONAL TRANSPORTATION ACCIDENTS:
Revision Date :
10/02/2007
Version:
1-800-424-9300
1-703-527-3887
8.3
Supersedes:
Chemtrec
Chemtrec
All Previous
I. CHEMICAL PRODUCT IDENTIFICATION
Product Name:
“1 SHOT
” Lettering Enamels (100-L through 199-L)
II. COMPOSITION/INFORMATION ON INGREDIENTS - (EXPOSURE LIMITS - SEE SECTION VIII)
INGREDIENT NAME
Stoddard solvent
1,2,4-Trimethylbenzene
Light Aromatic Solvent Naphtha
Xylene
Ethylbenzene
CAS #
8052-41-3
95-63-6
64742-95-6
1330-20-7
100-41-4
%
< 40
< 5
< 5
< 5
< 1
THE ITEMS LISTED BELOW ARE NOT CONTAINED IN MOST ENAMELS. SEE TABLE ON PAGE 2 TO DETERMINE WHICH COLORS CONTAIN THESE INGREDIENTS AND % WT.
INGREDIENT NAME
1,3,5-Trimethylbenzene
Aluminum
Aluminum oxide
Barium Sulfate
Benzimidazolone Compound(s)
Calcium Carbonate
Carbon Black
Copper
Crystalline Silica
Ferric Oxide
CAS #
108-67-8
7429-90-5
1344-28-1
7727-43-7
TS16251056
471-34-1
1333-86-4
7440-50-8
14808-60-7
1309-37-1
%
-
INGREDIENT NAME
Light Aliphatic Solvent Naphtha
Linseed Oil
Naphtha, hydrodesulfurized heavy
Nickel Antimony Titanium Rutile
Paraffinic Solvent
Polymerized Linseed Oil
Silicon Dioxide (amorphous)
Solvent Naphtha (petroleum), medium aliphatic
Talc
Titanium Dioxide
Zinc
CAS #
64742-89-8
8001-26-1
64742-82-1
8007-18-9
64742-47-8
67746-08-1
7631-86-9
64742-88-7
14807-96-6
13463-67-7
7440-66-6
%
-
III. HAZARDS IDENTIFICATION
HEALTH
FLAMMABILITY
REACTIVITY
HMIS
2*
2
0
"1 SHOT" Lettering Enamels v8.3
0 = Least
1 = Slight
2 = Moderate
3 = High
4 = Extreme
* = Chronic Health Effects
Page 1 of 7
100-L
10.6
3.4
101-L
102-L
103-L
104-L
106-L
108-L
109-L
110-L
111-L
114-L
115-L
116-L
117-L
118-L
120-L
124-L
130-L
132-L
134-L
141-L
142-L
143-L
144-L
148-L
149-L
150-L
151-L
152-L
153-L
154-L
155-L
156-L
157-L
158-L
160-L
161-L
162-L
163-L
164-L
165-L
168-L
191-L
193-L
195-L
199-L
11.6
9.2
11.7
8.7
8.0
8.4
10.5
10.5
10.6
9.6
9.2
11.2
10.3
11.3
11.8
10.5
11.3
11.3
11.0
8.8
9.4
8.6
9.3
9.0
10.2
9.0
11.3
9.0
9.2
10.9
8.2
8.3
8.8
8.3
9.4
8.3
8.2
8.8
8.7
8.3
11.2
11.0
8.8
9.6
7.8
3.0
3.5
3.0
3.1
3.0
3.2
4.0
3.9
4.0
3.4
3.3
3.1
3.2
3.0
3.0
3.6
3.5
3.7
3.7
3.3
3.5
3.4
3.8
3.6
3.3
3.3
3.0
3.4
3.4
3.0
3.5
3.3
3.3
3.0
3.3
3.2
3.5
3.3
3.3
3.4
3.6
3.4
4.0
3.2
2.2
Carcinogenicity:
OTHER
ALUMINUM
OXIDE
SILICON
DIOXIDE
(AMORPHOUS)
FERRIC
OXIDE
ZINC
COPPER
PARAFFINIC
SOLVENT
1,3,5TRIMETHYLBENZENE
‡
V.O.C.
LBS/GL
BARIUM
SULFATE
DENSITY
LBS/GL
TITANIUM
DIOXIDE
PRODUCT#
CARBON
BLACK
ADDITIONAL INGREDIENTS OF LETTERING ENAMELS -- Weight %
<1
<40
<1
<1
<1
<1
<1
<1
<1
< 40
< 1
< 1
<0.0
< 5
< 35
< 20
< 35
< 40
<20
<15
<15
<15
< 5
<10
< 5
<0.0
< 1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<1
<5
<5
<5
<5
< 30
< 10
< 40
< 15
< 20
< 35
< 5
< 5
< 15
< 5
< 20
< 5
< 5
< 15
< 15
< 5
< 35
< 20
< 5
< 25
< 25
< 25
< 25
< 30
< 20
< 5
*
< 5
*
< 10
< 20
< 15
*
< 5
< 5
< 5
< 5
< 5
< 5
*
*
*
*
*
< 5
< 5
*
*
< 5
< 5
< 5
< 5
*
< 5
*
< 30
< 1
<10
< 20
<5
IARC
Yes
Yes
No
No
No
No
No
No
No
No
NTP
No
No
No
No
No
No
No
No
No
No
OSHA
No
No
No
No
No
No
No
No
No
No
< 5
< 5
*
*
*
* See “List of Other Addtional Ingredients” at the end of this table for OTHER components.
‡ The VOC content is determined by using a percent solids basis, less water and exempt solvents, for adhesives, coatings and inks and the calculations of EPA
Reference Method 24 or equivalent ASTM method approved by the executive office.
"1 SHOT" Lettering Enamels v8.3
Page 2 of 7
* LIST OF OTHER ADDITIONAL INGREDIENTS
PRODUCT#
109-L
111-L
114-L
115-L
130-L
132-L
134-L
142-L
144-L
148-L
150-L
152-L
156-L
165-L
193-L
OTHER INGREDIENT
Solvent Naphtha (petroleum), medium aliphatic
Solvent Naphtha (petroleum), medium aliphatic
Talc
Crystalline Silica
Linseed Oil
Linseed Oil
Light Aliphatic Solvent Naphtha
Linseed Oil
Benzimidazolone Compound(s)
Calcium Carbonate
Nickel Antimony Titanium Rutile
Benzimidazolone Compound(s)
Nickel Antimony Titanium Rutile
Benzimidazolone Compound(s)
Nickel Antimony Titanium Rutile
Calcium Carbonate
Calcium Carbonate
Polymerized Linseed Oil
Naphtha, hydrodesulfurized heavy
Aluminum
Routes of Entry:
Medical Conditions Aggravated:
Immediate (Acute) Health Effects:
Inhalation:
CAS#
64742-88-7
64742-88-7
14807-96-6
14808-60-7
8001-26-1
8001-26-1
64742-89-8
8001-26-1
TS16251056
471-34-1
8007-18-9
TS16251056
8007-18-9
TS16251056
8007-18-9
471-34-1
471-34-1
67746-08-1
64742-82-1
7429-90-5
PERCENT
< 5
< 5
< 5
< 1
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
< 5
<20
CARCINOGENICITY
No
No
No
Yes (IARC, NTP only)
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Inhalation, Absorption, Ingestion, Skin contact, Eye contact.
Eye disease, Skin disease including eczema and sensitization, Kidney disease, Liver disease,
Digestive tract disease, Lung disease.
Can cause moderate respiratory irritation, dizziness, weakness, fatigue, nausea and headache. This
product may cause metal fume fever with resulting flu-like symptoms. Can cause severe central
nervous system depression (including unconsciousness).
Skin Contact:
Can cause moderate skin irritation, defatting, and dermatitis.
Eye Contact:
Can cause moderate irritation, tearing and reddening, but not likely to permanently injure eye
tissue.
Skin Absorption:
May cause irritation and minor systemic damage.
Ingestion:
Toxic if swallowed. May cause target organ failure and/or death. Can cause abdominal discomfort,
nausea, vomiting and diarrhea. Aspiration of material into the lungs can cause chemical
pneumonitis.
Target Organ Acute Toxicity:
Eyes, Skin, Respiratory System, Kidneys, Nervous System, Blood, Liver, Digestive Tract, Thyroid,
Pituitary, Testes Stomach, Cardiovascular System, Bone Marrow, Lymphatic System.
Long-Term (Chronic) Health Effects:
Inhalation:
Upon prolonged and/or repeated exposure, can cause moderate respiratory irritation, dizziness,
weakness, fatigue, nausea and headache.
Skin Contact:
Upon prolonged or repeated contact, can cause moderate skin irritation, defatting, and dermatitis.
Not likely to cause permanent damage.
Eye Contact:
Upon prolonged or repeated contact, can cause moderate irritation, tearing and reddening, but not
likely to permanently injure eye tissue.
Skin Absorption:
Upon prolonged or repeated exposure, harmful if absorbed through the skin. May cause severe
irritation and systemic damage.
Carcinogenicity:
IARC classifies ethylbenzene as “possibly carcinogenic to humans” (2B). See Tables on pages 2
and 3 for information on other components.
Target Organ Chronic Toxicity:
Nervous System, Eyes, Skin, Respiratory System, Kidneys, Blood, Liver, Digestive Tract,
Pituitary, Testes, Stomach, Cardiovascular System, Lymphatic System.
NOTICE - Reports have associated repeated and prolonged occupational overexposure to solvents
with brain and nervous system damage. Intentional misuse by deliberately concentrating and
inhaling the contents may be harmful or fatal.
Lifetime inhalation exposure of rats and mice to high concentrations of ethylbenzene (750 ppm)
resulted in increases in certain types of cancer, including kidney, lung and liver tumors. Testicular
adenomas were increased as were thyroid effects in rats at 750 ppm. Pituitary effects were
observed in female mice at 250 ppm. These effects were absent when exposure was below 75 ppm
ethylbenzene. The study does not address the relevance of these results to humans.
"1 SHOT" Lettering Enamels v8.3
Page 3 of 7
IARC has recently re-evaluated titanium dioxide as possibly carcinogenic to humans (Group 2B)
based on animal studies. However, human studies available to date do not suggest that
occupational exposure to titanium dioxide increases cancer risk. The ACGIH classifies titanium
dioxide as A4 (not classifiable as a human carcinogen). NTP does not classify it as carcinogenic.
IARC's evaluation shows inadequate evidence of carcinogenicity in humans, but sufficient
evidence of carcinogenicity in experimental animals. The evidence shows that high concentrations
of powdered and ultrafine titanium dioxide dust caused respiratory tract cancer in rats exposed by
either natural inhalation or direct introduction into the lungs. However, the same results are
observed in people working in dusty environments. Therefore, IARC extended this idea to workers
with exposures to titanium dioxide dust, if there are insufficient dust control measures in place.
Based on the IARC decision, Canadian officials have agreed that titanium dioxide is classifiable as
WHMIS D2A (carcinogen), and that it is not necessary to wait for release of the full monograph.
OSHA requires the status on US MSDSs to change within 90 days of publication in the IARC
monograph volume 93.
Only product #115-L contains Crystalline Silica (see List of Other Additional Ingredients, page 3):
Cutting, sanding or grinding dried or cured material may release particles of crystalline silica
(quartz). Exposure to airborne particles may cause lung damage including a risk of cancer. Chronic
exposure may result in chest pain, difficulty breathing, lung damage and silicosis. (Silicosis is the
permanent deposition of silica in lung tissue that results in lung damage.) There may exist a
relationship between silicosis and certain cancers.
This product contains pigments which may become a dust nuisance when removed by abrasive
blasting, sanding or grinding. See additional information above in this section for products
containing Crystalline Silica.
IV. FIRST AID
Inhalation:
Eyes:
Skin Contact:
Ingestion:
Remove to fresh air. If breathing is difficult, have a trained individual administer oxygen. If not
breathing, give artificial respiration and have a trained individual administer oxygen. Get medical
attention immediately.
Immediately flush eyes with plenty of luke warm water for at least 20 minutes retracting eyelids
often. Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate
medical attention and monitor the eye daily as advised by your physician.
Wash with soap and water. Remove contaminated clothing and launder. Get medical attention if
irritation develops or persists.
Seek medical advice immediately. Provide ingredients information from Section II of this MSDS to
the medical care provider. Contact your local Poison Control Center (listed in the telephone book),
or dial the local “Emergency” (911) number for additional information. Do not induce vomiting
unless instructed to do so by a physician or other competent medical personnel. Never give
anything by mouth to an unconscious person.
V. FIRE FIGHTING MEASURES
Flammability Summary:
Flash Point:
Autoignition Temperature:
Lower Flammable/Explosive Limit, % in air:
Combustible
41 ° C;
226 ° C;
1.0
Fire Hazards:
Empty containers that retain product residue (liquid, solid/sludge, or vapor) can be dangerous. Do
not pressurize, cut, weld, braze, solder, drill, grind or crush used containers. Do not expose
containers or product to heat, flame, sparks, static electricity, or other sources of ignition. Any of
these actions can potentially cause an explosion that may lead to injury or death. Dusts at sufficient
concentrations can form explosive mixtures with air. Water Reactive. Material will react with water
and may release a flammable gas. Vapors may be ignited by sparks, flames or other sources of
ignition if material is above the flash point giving rise to a fire (Class B). Vapors are heavier than
air and may travel to a source of ignition and flash back. This product, when dried or cured, may
support combustion when subjected to sources of ignition or heat in sufficient amount.
106 ° F
439 ° F
Upper Flammable/Explosive Limit, % in air:
6.0
Some products contain Linseed Oil (see List of Other Additional Ingredients on page 3). Rags,
steel wool or waste soaked with linseed oil may spontaneously catch fire if improperly discarded.
Immediately after use, place rags, steel wool or waste in a sealed water-filled container.
Extinguishing Media:
Use alcohol resistant foam, carbon dioxide, or dry chemical extinguishing agents. Water may be
ineffective but water spray can be used to extinguish a fire if swept across the base of the flames.
Water can absorb heat and keep exposed material from being damaged by fire.
Fire Fighting Instructions:
Do not enter fire area without proper protection including self-contained breathing apparatus and
full protective equipment. Fight fire from a safe distance and a protected location due to the
potential of hazardous vapors and decomposition products. Flammable component(s) of this
material may be lighter than water and burn while floating on the surface. Use water spray/fog for
cooling.
"1 SHOT" Lettering Enamels v8.3
Page 4 of 7
Hazardous Combustion Products:
Carbon dioxide, Carbon monoxide, Hydrogen, Toxic fumes, Toxic gases.
VI. ACCIDENTAL RELEASE MEASURES
Health Consideration for Spill Response:
Spill Mitigation Procedures:
General Methods:
Exposure to the spilled material may be irritating or harmful. Follow personal protective equipment
recommendations found in Section VIII of this MSDS. Additional precautions may be necessary
based on special circumstances created by the spill including: the material spilled, the quantity of
the spill, and the area in which the spill occurred. Also consider the expertise of employees in the
area responding to the spill. Evaporation of volatile substances can lead to the displacement of air
creating an environment that can cause asphyxiation.
Prevent the spread of any spill to minimize harm to human health and the environment if safe to do
so. Wear complete and proper personal protective equipment following the recommendation of
Section VIII at a minimum. Dike with suitable absorbent material like granulated clay. Gather and
store in a sealed container pending a waste disposal evaluation. Shut off ignition sources; including
electrical equipment and flames. Do not allow smoking in the area.
Ventilate the area by opening door and/or turning on fans and blowers.
Air Release:
Avoid runoff into storm sewers and ditches that lead to waterways. If runoff occurs, notify proper
authorities as required, that a spill has occurred. Retain all contaminated water for treatment.
Avoid runoff into storm sewers and ditches that lead to waterways.
Water Release:
Land Spills:
VII. HANDLING AND STORAGE
Handling:
Harmful or irritating; avoid overexposure to the material. Use only in a well ventilated area. As with
all chemicals, good industrial hygiene practices should be followed when handling this material. Do
not get in eyes, on skin and clothing. Use spark-proof tools and explosion-proof equipment. Ground
and bond containers when transferring material. May form flammable dust-air mixtures Guard
against dust accumulation of this material. Remove contaminated clothing and wash before reuse.
Launder work clothes frequently. "Empty" containers retain product residue (liquid and/or vapor)
and can be dangerous. Minimize dust generation and accumulation. Follow all protective equipment
recommendations provided in Section VIII. Avoid breathing material.
Storage:
Store in a cool dry ventilated location. Isolate from incompatible materials and conditions. Keep
container closed when not in use. Store in a cool place in original container and protect from
sunlight. Keep away from sources of ignition. Limit quantity of material stored.
VIII. ENGINEERING CONTROLS, PERSONAL PROTECTIVE EQUIPMENT AND EXPOSURE LIMITS
Local exhaust ventilation or other engineering controls are normally required when handling or
using this product to avoid overexposure. See table at the end of this Section VIII below for
exposure limits. Use process enclosures, local exhaust ventilation, or other engineering controls to
control airborne levels below recommended exposure limits. Explosion proof exhaust ventilation
should be used. Facilities storing or using this material should be equipped with an eyewash and
safety shower. Vapor concentrations should be monitored and controlled in accordance with 29
CFR 1910.1000.
Engineering Controls:
Protective Equipment:
Respiratory Tract:
If general or local exhaust ventilation is not available or sufficient to reduce exposure to below
acceptable levels, then respiratory protection is required to avoid overexposure when handling this
product. Wear a NIOSH approved respirator if any exposure is possible.
Wear safety glasses with side shields when handling this product. When the possibility exists for
eye contact with splashing or spraying liquid, or airborne material, wear additional eye protection
such as chemical splash goggles and/or face shield. Do not wear contact lenses. Have an eye wash
station available.
Wear protective gloves. Inspect gloves for chemical break-through and replace at regular intervals.
Clean protective equipment regularly. Wash hands and other exposed areas with mild soap and
water before eating, drinking, and when leaving work.
Wear chemically resistant gloves and apron. (Consult your safety equipment supplier).
Eyes:
Skin:
Protective Clothing:
CHEMICAL NAME
CAS #
ACGIH TLV
1,2,4-Trimethylbenzene
1,3,5-Trimethylbenzene
Aluminum
95-63-6 No TLV
108-67-8 No TLV
7429-90-5 10 mg/m3 TWA (metal dust)
Aluminum Oxide
1344-28-1 as Al: 10 mg/m3 TWA (The value is for
total dust containing no asbestos and <
1% crystalline silica)
7727-43-7 10 mg/m3 TWA (The value is for the
total dust containing no asbestos and
<1% crystalline silica)
Barium Sulfate
"1 SHOT" Lettering Enamels v8.3
OSHA PEL
IDLH
No PEL established
No PEL established
15 mg/m3 TWA (total dust); 5 mg/m3
TWA (respirable fraction)
total dust: 15 mg/m3 TWA; respirable
fraction: 5 mg/m3 TWA
Not determined.
Not determined.
Not determined.
15 mg/m3 TWA (total dust); 5 mg/m3
TWA (respirable fraction)
Not determined.
Not determined.
Page 5 of 7
Benzimidazolone Compound(s)
Calcium carbonate
Carbon black
Copper
TS16251056
471-34-1
1333-86-4
7440-50-8
Crystalline Silica
14464-46-1
Ethylbenzene
100-41-4
Iron oxide
1309-37-1
Light aliphatic solvent naphtha
Light Aromatic Solvent
Naphtha
Linseed Oil
Nickel Antimony Titanium
Rutile
Paraffinic solvent
Polymerized Linseed Oil
Silicon Dioxide (amorphous)
Titanium dioxide
Zinc
64742-89-8
64742-95-6
No TLV
No TLV
3.5 mg/m3 TWA
fume: 0.2 mg/m3 TWA; dusts and mists,
as Cu: 1 mg/m3 TWA
0.05 MG/M3 TWA (This TLV is for the
RESPIRABLE FRACTION of dust.)
100 ppm TWA
125 ppm STEL
as Fe: 5 mg/m3 TWA (welding fumes,
dust, total particulate (N.O.C.))
No TLV
No TLV
8001-26-1 No TLV
8007-18-9 0.2 mg/m3 (inhalable fraction of
insoluble nickel compound); As Sb: 0.5
mg/m3
64742-47-8 No TLV
67746-08-1 No TLV
7631-86-9 10 mg/m3 TWA
13463-67-7 10 mg/m3 TWA
7440-66-6 No TLV
No PEL established
No PEL established
3.5 mg/m3 TWA
0.1 mg/m3 TWA (fume); 1 mg/m3
TWA (dusts and mists)
SEE TABLE Z-3
Not determined.
Not determined.
1750 mg/m3 IDLH
dusts & mists as Cu: 100 mg/m3
IDLH
Not determined.
100 ppm TWA; 435 mg/m3 TWA
10 mg/m3 TWA
800 ppm IDLH (10 percent lower
explosive limit)
as Fe: 2500 mg/m3 IDLH
No PEL established
No PEL established
Not determined.
Not determined.
No PEL established
As Ni: 1 mg/m3 8hr TWA; As Sb: 0.5
mg/m3 8hr TWA
Not determined.
Not determined.
No PEL established
No PEL established
Respirable Dust: 20 mppcf
15 mg/m3 TWA (total dust)
No PEL established
Not determined.
Not determined.
3000 mg/m3 IDLH
Potential NIOSH carcinogen.
Not determined.
IX. PHYSICAL DATA
Liquid.
Aromatic
N/A
Not Determined.
Minimal
Heavier than air. Vapors that evolve from this product will tend to settle and accumulate near the
floor.
Slower than n-Butyl Acetate.
See Table on page 2.
See Table on page 2.
154 ° C;
309 ° F
N/A
Appearance:
Odor:
pH:
Octanol/Water Coeff:
Solubility in Water:
Vapor Density:
Evaporation Rate:
Density
V.O.C.
Initial Boiling Point
Initial Freezing Point
X. STABILITY AND REACTIVITY
Stability Information:
Stable under normal conditions. Spontaneous combustion can occur with products containing linseed oil.
Conditions to Avoid:
Sparks, open flame, other ignition sources, and elevated temperatures. Contamination. Contact with water.
Avoid spontaneous combustion of contaminated rags and other easily ignitable accumulations (example:
spray booth residue) by immediate immersion in water.
Chemical Incompatibility:
Chlorine, Strong oxidizing agents, Strong acids, Strong alkalies, Water, Moisture, Ethylene oxide.
Hazardous Decomposition Products:
Carbon dioxide, Carbon monoxide, Metal fumes, Hydrogen, Sulfur containing gases, Toxic fumes, Toxic
gases.
XI. TOXICOLOGICAL INFORMATION
Chemical Name
Benzene, 1,2,4-trimethylBenzene, ethylCarbon black
Carbonic acid, calcium salt (1:1)
Mesitylene
Solvent naphtha, light aromatic
Xylene
LD50/LC50
Inhalation LC50 Rat : 18 gm/m3/4H; Oral LD50 Rat : 5 gm/kg
Oral LD50 Rat : 3500 mg/kg; Dermal LD50 Rabbit : 17800 uL/kg
Oral LD50 Rat : >15400 mg/kg; Dermal LD50 Rabbit : >3 gm/kg
Oral LD50 Rat : 6450 mg/kg
Inhalation LC50 Rat : 24 gm/m3/4H
Oral LD50 Rat: 8400 mg/kg
Inhalation LC50 Rat: 5000 ppm/4H; Oral LD50 Rat: 4300 mg/kg; Dermal LD50 Rabbit: >1700 mg/kg
XII. ECOLOGICAL INFORMATION
Overview:
Care should be taken to minimize releases of any industrial chemicals to the environment.
"1 SHOT" Lettering Enamels v8.3
Page 6 of 7
XIII. DISPOSAL CONSIDERATIONS
Waste Description for Spent Product:
Disposal Methods:
Potential EPA Waste Codes:
Spent or discarded material is a hazardous waste. The waste is ignitable.
Information in this MSDS is provided only as a guide. Consult with competent authority to
determine proper waste disposal procedures. Clean up and dispose of waste and clean-up materials
in accordance with all federal, state, and local environmental regulations.
D001
Some Components Possibly Subjected to USEPA Land Disposal Restrictions:
When disposing of unused products or any waste, the preferred options are to send to a licensed reclaimer or to permitted incinerators. There may be some other ingredients subject to LDR categories.
Zinc
Xylenes (o-, m-, p- isomers)
Ethyl benzene
7440-66-6
1330-20-7
100-41-4
XIV. TRANSPORTATION INFORMATION
Agency Basic Description and Label
DOT
DOT by Land Transport: Not Regulated; DOT by Air and IATA (all modes): Paint, 3, UN1263, PG III, Label Required: Flammable Liquid
Hazardous Substance
Copper
RQ = 5000 pounds (2270 kg); The RQ for these hazardous substances is limited to those pieces of the metal having a
diameter smaller than 100 micrometers (0.004 inches).
RQ = 1000 pounds (454 kg); The RQ for these hazardous substances is limited to those pieces of the metal having a diameter
smaller than 100 micrometers (0.004 inches).
RQ = 100 pounds (45.4 kg); also listed as Xylene; also listed as Xylene (mixed); also listed as Benzene, dimethylRQ = 1000 pounds (454 kg)
Zinc
Xylenes (isomers and mixture)
Ethyl benzene
XV. REGULATORY INFORMATION
Regulation
SARA 313 Reportable :
Copper, Aluminium (fume or dust only), Zinc, 1,2,4-Trimethylbenzene, Xylene (mixed isomers), Ethyl benzene, Nickel
Compounds,Antimony Compounds.
TSCA Inventory :
All components of this product are listed in, or exempt from, the TSCA 8(b) Inventory.
M.S.D.S. Reportable HAP(s) :
Xylenes (isomers and mixture), Ethyl benzene, Nickel Compounds,Antimony Compounds.
California Proposition 65 :
The following statement is made in order to comply with the California Safe Drinking Water and Toxic Enforcement Act of 1986 Proposition 65: "WARNING: This product contains chemical(s) known to the State of California to cause cancer and birth defects
or other reproductive harm."
XVI. ADDITIONAL INFORMATION
Major References:
VENDOR'S MSDS's, PAINT & COATINGS HANDBOOK, EPA's LIST OF LISTS, AND OTHER PUBLISHED MATERIALS.
IMPORTANT: WHILE THE DESCRIPTIONS, DATA AND INFORMATION CONTAINED HEREIN ARE PRESENTED IN GOOD FAITH AND BELIEVED TO BE ACCURATE, THEY ARE
PROVIDED FOR YOUR GUIDANCE ONLY. MANY FACTORS MAY AFFECT PROCESSING OR APPLICATION OR USE, INCLUDING USE OF THIS MATERIAL IN COMBINATION
WITH OTHER MATERIALS OR PROCESSES. YOU THEREFORE SHOULD, AND THIS MATERIAL IS SUPPLIED ON THE CONDITION THAT YOU, PERFORM AN ASSESSMENT TO
DETERMINE THE SUITABILITY OF THE MATERIAL PRIOR TO USE, AND YOU ACCEPT RESPONSIBILITY FOR SATISFYING YOURSELF THAT THE MATERIAL IS SUITABLE AND
THE COMPLETENESS OF THIS INFORMATION IS SUFFICIENT FOR YOUR USE. NO WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED, DATA, OR INFORMATION SET FORTH. IN NO CASE SHALL THE DESCRIPTIONS, INFORMATION, OR
DATA PROVIDED BE CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE, AND WE DISCLAIM LIABILITY FOR LOSS OR INJURY ARISING FROM YOUR USE OF
THIS MATERIAL, DATA OR INFORMATION. FURTHER, THE DESCRIPTIONS, DATA AND INFORMATION FURNISHED HERE ARE GIVEN GRATIS. NO OBLIGATIONS NOR
LIABILITIES FOR THE DESCRIPTION, DATA AND INFORMATION GIVEN ARE ASSUMED, ALL SUCH BEING GIVEN AND ACCEPTED AT YOUR RISK.
"1 SHOT" Lettering Enamels v8.3
Page 7 of 7
`