SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 ROBERT BOSCH NORTH AMERICA Engineering Technical Center 15000 Haggerty Rd. Plymouth, MI 48170 Timothy O’Dell Phone: 734 979 3527 MECHANICAL Valid To: June 30, 2016 Certificate Number: 3305.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on electrical/electronic control modules: Test Electrical Point Functional/Parametric Check Jump Start Reverse Polarity Over Voltage Discrete Digital Input Threshold Voltage Crank Pulse Capability and Durability Power Supply Interruptions Battery Voltage Dropout Mechanical Crush for Housing – Elbow Load1 Crush For Housing – Foot Load1 Connector Tests1 Connector Installation Abuse – Side Force1 Connector Installation Abuse – Foot Load1 Test Method(s) CETP-00.00-E-412, CS-11982, ISO 16750-2, GMW3097, GMW3172 GMW3172, GMW3191, USCAR-25 Up to 50 KN of applied force, Speeds of 1 to 500 mm/sec Thermal Shock (TS) Thermal Shock Air-to-Air1 CETP-00.00-E-412, CS-11982, GMW3172, ISO 16750-4 Temperature Range: (-70 to 200)˚C Max Product Load: Up to 50 lbs Temp Transition between Environments: <30s Thermal Cycle Transitions: Up to 20˚C/min Visual Inspections Scanning Electron Microscopy Optical Microscopy (A2LA Cert. No. 3305.01) 10/03/2014 CETP-00.00-E-412, CS-11982, GMW3172 Page 1 of 2 Test Temperature Humidity Temperature Measurement1 Low Temperature Wakeup1 Frost1 High Temperature Degradation1 Power Temperature Cycle1 Humid Heat Cyclic1 Humid Heat Constant1 Test Method(s) GMW3172, CS-11982, CETP-00.00-E-412, ISO 16750-4. IEC 60068-2-38, IEC 60068-2-78 Temperature Range: (-70 to 170) °C Max Product Load: Up to 100 pounds Temperature Transition Rate: 15 °C/min max Humidity Range: (33 to 98) %RH Vibration Vibration With Thermal Cycling1 Post Thermal Fatigue Vibration1 Shipping Vibration1 ASTM D4728, CETP- 00.00-E-412, CS-11982, GMW3172, IEC 60068-2-64 Random, Sine, Sine-on-Random Resonance Search and Dwell Frequency Range: (5 to 2,500) Hz Force Capabilities: Up to 14,000 lb. Force Displacement: Up to 3 inch Peak-to-Peak Temperature Range: (-73 to 190)°C Temperature Transition Rate: 5°C/minute max Humidity Range: (33 to 98)% RH Multiple Channel Control/Monitoring Mechanical Shock Mechanical Shock – Pothole1 Mechanical Shock – Collision1 Mechanical Shock – Closure Slam1 CETP-00.00-E-412, CS-11982, Fiat 9.90110, GMW3172, IEC 60068-2-27 Waveform: Half-Sine, Triangular Maximum g Level: Up to 800g Duration: (1 to 30) ms Corrosion Salt Fog1 Salt Mist1 ASTM B117 GMW3172, IEC 60068-2-52 Ambient Temp to 70˚C Ambient to 100% RH Free Fall GMW3172 1 Also using the above methods and customer supplied test methods directly related to the capabilities listed above. (A2LA Cert. No. 3305.01) 10/03/2014 Page 2 of 2 A2LA has accredited ROBERT BOSCH NORTH AMERICA Plymouth, MI for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 3rd day of October 2014. _______________________ President & CEO For the Accreditation Council Certificate Number 3305.01 Valid to June 30, 2016 For the tests to which this accreditation applies, please refer to the laboratory’s Mechanical Scope of Accreditation.
© Copyright 2018