NATIONAL INSTITUTE OF TECHNOLOGY

NATIONAL INSTITUTE OF TECHNOLOGY
HAZRATBAL, SRINAGAR- 190006 (J&K)
(Planning & Development Wing)
Tel: 0194-2424792/2429423/2424809/24247972102157 Fax: 0194-2420475
N.I.T No. 03 of 2015
For & on behalf of Chairman Board of Governors NIT Srinagar, sealed tenders affixed with a revenue stamp of
Rs. 10/- are invited from Contractors registered with state PWD, CPWD, MES for the below mentioned works:S. No
Particulars of Items
Cost of work
01.
02.
03.
Renovation of Solar House
Construction of Pathways.
Renovation of Reception
Centre
Rs. 8.69 lacs
Rs. 51.75 lacs
Rs. 7.37 lacs
Earnest
money
Rs. 17,380/Rs. 1,03,500/Rs. 14,740/-
Comp.
period
70 days
90days
70 days
Class of
contractor
C & D Class Civil
A Class Civil
C & D Class Civil
Cost of
T.D
Rs. 200/Rs. 500/Rs. 200/-
TERMS & CONDITIONS:1. The tenders should be addressed to Dean P&D, NIT Srinagar which must reach his office on or before 27-0415 by Speed Post/Courier up to 3.00 P.M.
2. The tenders shall be opened on date convenient to the Contract committee in presence of contractors who
wish to be present.
3. The Tender documents will be available on the NIT website “www.nitsri.net from 09-04-15. The cost of
downloaded tender document as shown above in the table should be credited into NIT chest bearing A/C No:
039101010000106.
4. The Contractor has to submit his documents in main envelope containing two additional envelopes, as
Envelope ‘A’ and Envelope ‘B’. The main envelope should clearly indicate the name of the Contractor and the
name of the work for which tender is being submitted. The Envelope ‘A’ and Envelope ‘B’ should contain the
details as given below and on each envelope cover should clearly indicate the name of the contractor and
details of matter inside the envelope:
5.
Envelope ‘A’
i)
Copy of valid enlistment card
ii) Sales Tax registration, Tin number
iii) CDR of amount shown against the Work Pledged to Executive Engineer NIT Srinagar.
iv) PAN No.
v) Receipt of Cost of Tender Document.
Envelope ‘B’
Quantity schedule with quoted rates covered with transparent tape.
6.
7.
8.
The envelope ‘B’ will be entertained only if the contractor qualifies the pre-requisite condition on the basis of
the documents provided in Envelope ‘A’.
In case the last date of receipt of tenders happens to be a holiday, tenders will be received on next working
day up to 12 Noon.
Other terms and conditions shall be available in the tender document/Qty schedule.
(DEAN P&D)
N. I. T Srinagar
NO: NIT/P&D/2015/415-422
DT: 09-04-2015
Copy to:1. Associate Dean/Ex. Engineer NIT Srinagar for information please.
2. Registrar NIT Srinagar for information please.
3. Deputy Registrar (Accounts) for information please.
4. Assistant Executive Engineer for information please.
5. O/C Estates for information please.
6. Estates Engineer for information please
7. P.A to Director for information of the Director please.
8. Institute Website in charge with the request to get the N.I.T and Tender Document up loaded in the Web
Sites.
Quantity Schedule of Renovation of Solar House
ADVT. COST : Rs. 8.69 lacs
S. NO
01
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13
14
15.
16.
ITEM
QTY.
Brick work with common burnt clay F.P.S. (non 1.1 Cum
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V level in
all shapes and sizes in : Cement mortar 1:6 (1 cement :
6 coarse sand)
Replacing of kail wood frames for doors, windows
5.8 cft
Replacement of damaged/missing wooden shutters of
Kail wood (35mm thick) for doors excluding paneling
P/F of paneling for doors (25mm to 40mm) thick Kail
wood
Providing and fixing of paneled and glazed shutters for
windows and clerestory windows, with 4 mm thick
glass pans including ISI marked M.S pressed butt hinges
bright finished of required size with necessary screws,
all complete as per direction of Engineer-in-charge kail
wood (35mm thick shutters)
Removing of mud/cement plaster from walls including
cleaning.
15 mm cement plaster on the rough side of single or
half brick wall of mix
1:6 (1cement : 6 Coarse sand)
Earth work in surface excavation not exceeding 30 cm
in depth but exceeding 1.5 m in width as well as 10 sqm
on plan including disposal of excavated earth up to 50
m and lift up to 1.5 m disposed soil to be leveled and
nearly dressed( All Kinds of soil)
P/L soling hand packed including ramming and
carriage complete
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering - All work up to plinth level : 1:4:8 (1 Cement
: 4 coarse sand : 8 graded stone aggregate 40 mm
nominal size)
Cement concrete flooring 1:2:4 (1 cement: 2 coarse
sand: 4 graded stone aggregate) finished within a
floating coat of neat cement, concluding cement slurry,
but excluding the cost of nosing of steps etc. complete.
40 mm thick with 20mm nominal size stone aggregate
Dismantling roofing including ridges ,hips, valleys and
gutters etc and stacking the material within 50 mm
lead of:- G.S Sheet
P/F of polymare colour coated G.S. sheet roofing high
rib 0.50 mm thick
P/F of polymare colour coated G.S. sheet ridge 0.50 mm
thick
Providing and fixing of imported pannelling 12 mm
thick incl. frame work of budloo wood 2”x1.5”
P/F of kail wood planks for stair steps planed
CPWD
RATE
TO
BE
DSR 2013 QUOTED
BY
CONTRACTOR
5325.10
N.A
19.52
sm
13.66
sm
7.63 sm
N.A
256.74
sm
447.61s
m
N.A
139.13
sm
4553.55
Per 100
Sqm
21.20
cum
10.60
cum
N.A
141.08
sm
316.8
171.00
sm
56.8
171.00
sm
14.02
rm
42.38
sm
10.0 cft
N.A
N.A
N.A
164.75
3,920.65
N.A
N.A
N.A
17.
18.
19.
20.
21.
22.
23.
24.
25
26.
27.
28.
29.
Applying priming coat:
With ready mixed pink or Grey of approved brand and
manufacturing on wood work (hard & soft wood)
Painting with synthetic enamel paint of approved
brand and manufacture to give an even shade:
Two or more coats on new work
Distempering with oil bound washable distemper of
approved brand and manufacture to give an even
shade:
New work (one or more coats)
Providing and aplying plaster of paris putty of 2mm
thickness overplastered surface to prepare the surface
even and smooth complete.
Finishing walls with water proofing cement paint of
required shade (snowcen)
New work (Two or more coats applied @ 3.84 kg/10
sqm)
Providing Fibre glass roofing comprising 2mm
(nominal) thick corrugated Fibre glass sheets fixed to
the supporting structure with 8 mm dia GI (J/L) bolts
G.I limpet & bituminous felt washers complete but
excluding the cost of supporting structure including
removing of existing Fibre glass sheets complete.
Renewing glass panes, with wooden fillets wherever
necessary Float glass panes of thickness 4 mm
Providing & Fixing ISI marked aluminum butt hinges
anodized (anodc coating not let that grade AC 10 as per
IS: 1868) transparent or dyed to required colour or
shade with necessary screws etc. complete.(100 x 75 x 4
mm)
Providing and fixing aluminum sliding door bolts, ISI
marked, anodized (anodic coating not less than grade
AC 10 as per IS: 1868) transparent or dyed to required
colour or hade, with necessary screws etc. complete:
250x16mm
Providing and fixing aluminum nuts tower bolts, ISI
marked, anodized (anodic coating not less than grade
AC 10 as per IS: 1868) transparent or dyed to required
colour or shade, with necessary screws etc. complete:
(a)300 mm x10mm
223.39
sm
30.75
223.39
sm
63.05
242.38
sm
79.65
242.38
sm
100.95
131.47
sm
54.40
26.02
Sm
N.A
14.29
sm
8 No.’s
825.95
6 No.’s
180.45
6 No.’s
108.10
(b) 250 mm x 10 mm
Providing and fixing aluminum handles, ISI marked,
anodized (anodic coating not less than grade AC 10 as
per IS: 1868) transparent or dyed to required colour or
hade, with necessary screws etc. complete: 100mm
Providing ad laying Ceramic glazed floor tiles of size
300x300 mm (thickness to be specified by the
manufacturer), of 1st quality conforming to IS : 15622,
of approved make, in all colours, shades, suchWhite,
Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed
of cement mortar 1:4 (1cement: 4 Coarse sand),
including pointing the joints with white cement and
matching pigments etc. complete.
Providing and fixing Ist quality ceramic glazed wall
tiles conforming to IS: 15622 (thickness to be specified
06 No’s
12 No.
90.65
52.80
24.72
sm
822.1
20.54
sm
793.6
89.0
35.
by the manufacturer) of approve make, in all colors,
shades except burgundy, bottle green, black of any size
as approved by Engineer in charge in skirting, riser of
steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand) and jointing with grey cement
slurry @ 3.3 kg per sqm, including pointing in white
cement mixed with pigment of matching shade
complete.
Providing and fixing of water closet squatting pan
(Indian type W.C pan) with 100mm sand cast Iron P or
S trap. 10 liter low level white PVC flushing cistern with
manual controlled device (handle lever) conforming to
I.S. 7231 Parry ware/Hind ware/ Cera with all fittings
and fixtures complete including cutting and making
good the walls and floors wherever required: white
vitreous china long pan pattern W.C pan of size 580mm
x440 mm with integral type foot rests.
Providing and fixing wash basin with C.I brackets, 15
mm C.P brass pillar taps, 32 mm C.P brass waste of
standard pattern, including painting of fittings and
brackets, cutting and making god the walls wherever
require White Vitreous china Wash basin size 630x450
mm with a pair of 15 mm C.P. brass pillar taps.
Providing & fixing G.I Pipes complete with G.I fittings
and clamps i/c making good the walls etc concealed
pipe, including painting with anti corrosive bitumastic
paint, cutting chases and making good the wall :
i)
15 mm dia nominal bore.
ii)
20 mm dia nominal bore.
Providing and fixing CP brass angle valve 15 mm bore
heavy (Parco/jaguar)for Basin mixer geyser point of
approved quality conforming I.S 8931
Providing and fixing CP brass bib cock 15 mm bore
heavy (Parco / Jaguar)
Providing and fixing of mirror with shelf
36.
Providing and fixing CP grating 100 mm
2 No.
N.A
37.
Providing and fixing floor trap PVC
1 No.
N.A
38.
Providing and fixing PVC Waist pipe for wash basin 32
mm
Providing and fixing G.I. pipes complete with G.I
fittings including trenching and refilling etc. (20 mm
dia nominal bore)
Providing and fixing of water heater (geyser) 50 lt. incl
CP tubes geyser bolts etc. (Venus/Bajaj)
Providing and fixing of PVC pipe 100mm dia incl.
fittings for disposal system
Providing and fixing of 2’ long towel rod c.p
1 No.
72.55
9 RM
186.25
1 No.
14,500
40 RM
N.A
1 No.
N.A
Providing and fixing of PVC pipe 50mm dia fittings for
disposal system.
Construction of brick masonry main holes 3’x3’x2’
outside size complete in all respects incl. C.I. cover and
frame 16”x16”.
Varnishing with app. Brand and manufacture two or
more coats with copal varnish over under coat of
flatting varnish
5 RM
N.A
6 No.’s
N.A
42.38
sm
96.35
30.
31.
32.
33.
34.
39.
40.
41.
42.
43.
44.
45.
1 No.
3,265.25
1 No.
2,174.65
15 rm
8 rm
3 No.
263.7
298.05
506.7
3 No.
458.40
1 No.
N.A
46.
(a)
46
(b)
46
(c)
Carriage of Sand from Ganderbal to NIT by mechanical
transport for average lead of 11 Km
Carriage of 20mm stone aggregate from Athawajan to
NIT via Bye Pass by mechanical transport for average
lead of 25 Km
Carriage of bricks from Pampore for an average lead of
35 km
5.43
cum
14.57
cum
174.32
523 No.
875.8
292.76
TERMS AND CONDITIONS
1. If any omission is found in the specification / rate of item or there is an any typographical error in
the rate/item, the same shall be read as per approved estimate
2. The supply if found defective /not as per approved specifications, the item will not be accepted and
will have to be replaced at the risk & cost of allottee.
3. Work has to be executed strictly in accordance with the specifications provided in the item within
70 days falling which penalty @ Rs.500/- per day shall be imposed.
4. The rates should be inclusive of all taxes/octri etc. Further taxes like Service Tax plus surcharge,
Income tax, Labour-cess or any other tax as required under rules shall be deducted from the bills of
contractor.
5. No advance shall be paid during execution of work.
6. The rates should be written clearly and legible both in words and figures and avoid corrections.
Further all rates should be covered with transparent tape.
7. The tenders will be valid for 120 days from the date of opening of tenders.
8. Defects liability period (DLP) shall be six months after completion of work which shall be
considered as the defective liability period from the date of completion. During this period if any
defect is found, the same are required to be rectified by the Contractor. In case the contractor fails
to do so, the Engineer In charge may get these defects rectified up to its satisfaction by any other
agency at the risk and cost of the original contractor. The amount/cost involved for rectification
will be recovered from the security deposit or any other amount/cost involved for the original
contractor. 10% bill deposit shall be retained till DLP expires.
9. Any tenderer quoting “Free of Cost” for any item of work, the tender shall be rejected.
10. The tenderer quoting “Rebate” on comparative cost or on item of rate will be rejected. Contractor
should thus adjust amount within the quoted rate structure.
11. The splitting of quantity of any item i.e. quoting of more than one rate for the item is not accepted.
12. The contractors are advised to see the site before tendering.
13. The tender must be accompanied by CDR pledged to Dean P&D, NIT Srinagar for the amount shown
against the work. Tenders without CDR will be straightway rejected and released CDR shall not be
accepted.
14. In case the date of receipt of tender happens to be holiday, the same shall be received on the next
working day up to 12 noon.
15. Only JK cement or Khaber Grade 43 shall be entertained for cement works .
16. The competent authority reserves the right to reject any tender without assigning any reason
thereof.
17. All other terms and conditions shall remain the same as given in tender notice/NIT-cumAgreement.
(I/C Ex. Engineer)
N.I.T. Srinagar
ALL THE CONDITIONS ARE ACCEPTABLE TO ME
(Signature of Contractor)
Name: _____________________________S/O : _______________________________
R/O : _______________________________Ph. No: ___________________________
Quantity Schedule /rate list of Construction of Pathways
ADVT. COST : Rs. 51.75 lacs
S. NO
ITEM
QTY.
01.
Earth work in excavation by mechanical means 134.62
(Hydraulic excavator)/manual means in foundation Cum
trenches or drains (nor exceeding 1.5 m in width or 10
sqm on plan), including dressing of sides and ramming
of bottoms, lift up to 1.5m, including getting g out the
excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m
02.
Disposal of building rubbish / malba / similar
unserviceable, dismantled or waste materials by
mechanical means, including loading,
transporting, unloading to approved municipal
dumping ground or as approved by Engineer-incharge, beyond 50 m initial lead, for all leads
including all lifts involved.
03.
04.
05.
06.
07.
08.
09.
10.
Surface dressing of the ground including removing
vegetation and inequalities not exceeding 15 cm deep
and disposal of rubbish, lead up to 50 m and lift up to
1.5 m.
Providing & laying of stone soling hand packed 75mm
thick including all mechanical and manual carriages up
to the site.
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering-All work up to plinth level: 1:4:8 (1 cement :
2 coarse sand : 4 graded stone aggregate 40 mm
nominal size)
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering-All work up to plinth level: 1:3:6 (1 cement :
2 coarse sand : 4 graded stone aggregate 40 mm
nominal size)
Providing and laying in position cement concrete of
specified grade excluding the cost of centering and
shuttering-All work up to plinth level: 1:2:4 (1 cement :
2 coarse sand : 4 graded stone aggregate 20 mm
nominal size)
Centering & shuttering including strutting, propping
etc. and removal of the form work for foundations,
footings, bases for column
15 mm cement plaster on the rough side of single or
half brick wall of mix 1:4 (1 cement : 4 fine sand)
Providing & fixing of vitrified Heavy Duty paving tiles
of size 300mmx300mm to Foot paths of approved
Quality
,Design
color
viz
Kajaria
/Hindware/Somany/Bonzer of 10 mm thick laid over
CPWD
DSR 2013
Rs. 148.25
107.69
Cum
Rs.
123.85/-
615
Sqm
Rs.
1124.60/100 sq.m
243.27
Cum
N.A
205
Cum
Rs.
3920.65/-
73.13
Cum
Rs.
4230.50/-
133.77
Cum
Rs.
4921.70/-
1171.00
Sqm
Rs. 186.40
1171.
Sqm
14750
Sft
Rs. 168.55
N.A
RATE
TO
BE
QUOTED
BY
CONTRACTOR
20mm thick cement sand bed in 1:4 ( 1 Cement:4
Course sand )Complete Job(Sample to be approved from
Engineer Incharge )
11.
Kota stone slab flooring over 20 mm (average) thick 92.90
Rs.
base laid over and jointed with grey cement slurry Sqm
1071.70
mixed pigment to match the shade of the slab, including
rubbing and polishing complete with base of cement
mortar 1:4(1 cement: 4 coarse sand):
25 mm thick
12.
Providing and fixing of M.S. Pipes of 150 mm dia. 24.39
N.A
Including Carriage
RM
13.
Carriage of Sand from Ganderbal to NIT by mechanical 202.0
Rs.
transport for average lead of 11 Km
Cum
174.32/14.
Carriage of 20mm stone aggregate from Athawajan to 370.71
Rs.
NIT via Bye Pass by mechanical transport for average Cum
269.39/lead of 25 Km
TERMS AND CONDITIONS
1. If any omission is found in the specification / rate of item or there is an any typographical error in
the rate/item, the same shall be read as per approved estimate
2. The supply if found defective /not as per approved specifications, the item will not be accepted and
will have to be replaced at the risk & cost of allottee.
3. Work has to be executed strictly in accordance with the specifications provided in the item within
90 days falling which penalty @ Rs.500/- per day shall be imposed.
4. The rates should be inclusive of all taxes/octri etc. Further taxes like Service Tax plus surcharge,
Income tax, Labour-cess or any other tax as required under rules shall be deducted from the bills of
contractor.
5. No advance shall be paid during execution of work.
6. The rates should be written clearly and legible both in words and figures and avoid corrections.
Further all rates should be covered with transparent tape.
7. The tenders will be valid for 120 days from the date of opening of tenders.
8. Defects liability period (DLP) shall be six months after completion of work which shall be
considered as the defective liability period from the date of completion. During this period if any
defect is found, the same are required to be rectified by the Contractor. In case the contractor fails
to do so, the Engineer In charge may get these defects rectified up to its satisfaction by any other
agency at the risk and cost of the original contractor. The amount/cost involved for rectification
will be recovered from the security deposit or any other amount/cost involved for the original
contractor. 10% bill deposit shall be retained till DLP expires.
9. Any tenderer quoting “Free of Cost” for any item of work, the tender shall be rejected.
10. The tenderer quoting “Rebate” on comparative cost or on item of rate will be rejected. Contractor
should thus adjust amount within the quoted rate structure.
11. The splitting of quantity of any item i.e. quoting of more than one rate for the item is not accepted.
12. The contractors are advised to see the site before tendering.
13. The tender must be accompanied by CDR pledged to Dean P&D, NIT Srinagar for the amount shown
against the work. Tenders without CDR will be straightway rejected and released CDR shall not be
accepted.
14. In case the date of receipt of tender happens to be holiday, the same shall be received on the next
working day up to 12 noon.
15. Only JK cement or Khaber Grade 43 shall be entertained for cement works .
16. The competent authority reserves the right to reject any tender without assigning any reason
thereof.
17. All other terms and conditions shall remain the same as given in tender notice/NIT-cumAgreement.
(I/C Ex. Engineer)
N.I.T. Srinagar
ALL THE CONDITIONS ARE ACCEPTABLE TO ME
(Signature of Contractor)
Name: _____________________________S/O : _______________________________
R/O : _______________________________Ph. No: ___________________________
Quantity Schedule of Renovation of Reception Centre
ADVT. COST : Rs. 7.37 lacs
S. NO
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
ITEM
Dismantling cement asbestos or other hard board
ceiling or partition walls including stacking of
serviceable meterials and disposa of unserviceable
materials with in 50 lead.
Porivding and fixing of 12 mm thick ply Wood Ceiling
complete
Providing and fixing of ornamenal cornice 2.5”x2.5” of
budloo wood
Removing dry or oil bound distemper, water proofing
cement paint and the the like by scrapping, sand
papering and preparing the surgace smooth including
necessary repairs to scratches etc. Complete.
Distempering with oil bound washable distemper of
approved brand and manufacture to give an even
shade: New work (two or more coats) over and
including water thin able priming coat with cement
primer
Providing and fixing of Bujj Tiles (Brick Cladding) for
the walls of approved and manufacture of required
shade and colour as directed by the Engineer-in-charge
on 15mm thick bed of cement mortar 1:3 (1 cement : 3
coarse sand)
Dismantling roofing including ridges, hips, valleys, and
gutters, etc and stacking the material within 50 meters
lead.
a) G.S SHEET
Providing & fixing of poly coated tile profile G.I. Sheet
roofing including bolts and nuts
Providing & fixing of poly coated tile profile G.I. Sheet
ridge of 0’-9” width
Providing & fixing of ornamental planed eaves
boarding 250 mm x 25 mm size of 1st class kail wood etc
complete.
Providing and fixing wood work in soffit 25 mm thick of
1st class Kail wood, sawn and fixed position etc.
complete.
Painting with synthetic enamel paint of approved
brand and manufacture to give an even shade:
Two or more coats on new work
French spirit polishing: Two or more coats on new
works including a coat of wood filler.
Dismantling dmaged Kota Stone flooring including
shifting of same to dumping site as directed by the
engineer-in-charge
QTY.
80.29
Sqm
CPWD
RATE
TO
BE
DSR 2013 QUOTED
BY
CONTRACTOR
Rs. 19.80
DSR
864.00
Sft
79.87
RM
146.38
Sqm
N.A
146.38
Sqm
Rs.
79.65 /-
769.00
SFt
N.A
146.77
Sqm
Rs. 56.80
104.39
Sqm
42.07
RM
35.98
RM
N.A
27.42
Sqm
N.A
157.32
Sqm
Rs.
63.05
36.55
Sqm
16.06
Sqm
Rs.
175.50
N.A
Rs. 50 MR
N.A
N.A
N.A
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
Kota stone slab flooring over 20 mm (average) thick
base laid over and jointed with grey cement slurry
mixed pigment to match the shade of the slab, including
rubbing and polishing complete with base of cement
mortar 1:4(1 cement: 4 coarse sand):
25 mm thick
Renewing glass panes, with wooden fillets wherever
necessary: Float glass panes of thickness 4 mm
16.06
Sqm
Rs.
1071.70
6.97
Sqm
Rs.
825.95
Providing and laying Ceramic glazed floor tiles of size
300x300mm (thickness to be specified by the
manufacturer) of 1st quality conforming to IS: 15622 of
approved make in colours such as White, Ivory, Grey,
Fume Red Brown, laid on 20 mm thick cement mortar
1:4 (1 Cement : 4 Coarse sand), including pointing the
joints with while cement and matching pigment etc.
complete
Providing and fixing Ist quality ceramic glazed wall
tiles conforming to IS: 15622 (thickness to be specified
by the manufacturer) of approve make, in all colors,
shades except burgundy, bottle green, black of any size
as approved bu Engineer in charge in skirting, riser of
steps,dados over 12 mm thick bed of cement mortar 1:3
(1 cement: 3 coarse sand) and jointing with grey
cement slurry @ 3.3 kg per sqm, including pointing in
white cement mixed with pigment of matching shade
complete.
Providing and fixing mirror of superior glass (of
approved quality) and of required shape and size with
plastic molded frame of approved make and shade with
6mm hardboard backing complete.
a) Circular shape 450mm dia.
Providing and fixing of C.P brass bib cock of approved
quality conforming to IS:8931Parko Vic/Mark/Cera)
15MM NOMINAL BORE
Providing and fixing of water heater (geysers) of
Venus/Bajaj make including cost of dash fasteners with
nuts and washers C.P. tubes complete 35 liters
Providing and fixing of 15 mm dia chromium plated
cast brass angle valve of approved quality
Parke/Vic/Mark/Cera
C.P Long bends of required size of approved quality
10.41
Sqm
Rs.
822.10
58.55
Sqm
Rs.
793.60
2 No.’s
Rs.
856.65
06 No.’s
Rs.
458.40/
02 No.’s
N.A
08 No.’s
N.A
02 No.’s
N.A
Providing and fixing of floor trap complete PVC (Prince 02 No.’s
Make) 100mm dia.
Providing and fixing wash basin (Cera) with 02 No.’s
CI/MS/brackets including painting of fittings and
brackets, cutting an making good walls wherever
required white vitreous china wash basin size
630x450mm with a pair of 15mm C.P brass pillar taps
and 32mm dia. C.P. brass union.
N.A
Demolishing cement concrete manually/ by 0.793
mechanical means including disposal of material Cum
with in 50 m lead as per direction of Engineer - in charge.
Nominal concrete 1:3:6 or richer mix (i/c
Rs.
806.35/-
Rs.
2174.65/-
equivalent design mix) Floor:
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
Providing and laying in position cement concrete
of specified grade excluding the cost of centering
and shuttering - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size)
Providing and fixing of PVC Prince pipe (Type” ) in
proper gradient in excavated trenches including
jointing and refilling the excavated material
complete including cost of excavation.
75mm dia. Pipe
Providing and fixing of following PVC fittings.
(Prince Make), Plain bend :75 mm
Door Bend (PVC Prince Make)
100 mm
Door Junction (PVC Prince Make)
100 mm
Providing and fixing G.I. Pipes complete with G.I.
fittings and clamps, i/c making good the walls etc.
concealed pipe, including painting with anti
corrosive bitumastic paint, cutting chases and
making good the wall :15 mm dia nominal bore
Dismantling manually old wash basin and shifting
of same with in 50 m lead etc. complete
For one wash basin, 1 no mazdoor
For two wash basin,
Dismantling manually old PVC/CI/Vitreous china
flushing cistern and shifting of same to the estate
store etc. complete
For one cistern, 1 no mazdoor
For two cistern
Providing and fixing P.V.C. low level flushing
cistern with manually controlled device (handle
lever) conforming to IS: 7231, with all fittings and
fixtures complete.
10 litre capacity – White
Providing and fixing of CP grating etc. complete
100 mm
Towel rod Parko Vic/Mark/Cera)
0.793
Cum
Rs.
4921.70/-
13.72
RM
N.A
03 No.’s
N.A
02 No.’s
N.A
02 No.’s
N.A
15.00
RM
N.A
02 No.’s
N.A
02 No.’s
Rs. 300.00
DSR
02 No.’s
Rs. 853.00
DSR
02 No.’s
N.A
02 No.’s
N.A
Wood work in frames of false ceiling, partitions,
etc. sawn and put in position with popular wood.
P/F of polynium bubble insulation sheets over
6mm thick foam sheet fixed over wooden rough
flooring with budloo wood beading 25x5 mm size.
Carriage of Sand from Ganderbal to NIT by
mechanical transport for average lead of 11 Km
Carriage of 20mm stone aggregate
from
Athawajan to NIT via Bye Pass by mechanical
transport for average lead of 25 Km
27.89
Cft
864.00
Sft
N.A
0.357
Cum
0.713
Cum
Rs.
174.32
Rs.
269.39/-
Rs. N.A
TERMS AND CONDITIONS
1. If any omission is found in the specification / rate of item or there is an any typographical error in
the rate/item, the same shall be read as per approved estimate
2. The supply if found defective /not as per approved specifications, the item will not be accepted and
will have to be replaced at the risk & cost of allottee.
3. Work has to be executed strictly in accordance with the specifications provided in the item within
70 days falling which penalty @ Rs.500/- per day shall be imposed.
4. The rates should be inclusive of all taxes/octri etc. Further taxes like Service Tax plus surcharge,
Income tax, Labour-cess or any other tax as required under rules shall be deducted from the bills of
contractor.
5. No advance shall be paid during execution of work.
6. The rates should be written clearly and legible both in words and figures and avoid corrections.
Further all rates should be covered with transparent tape.
7. The tenders will be valid for 120 days from the date of opening of tenders.
8. Defects liability period (DLP) shall be six months after completion of work which shall be
considered as the defective liability period from the date of completion. During this period if any
defect is found, the same are required to be rectified by the Contractor. In case the contractor fails
to do so, the Engineer In charge may get these defects rectified up to its satisfaction by any other
agency at the risk and cost of the original contractor. The amount/cost involved for rectification
will be recovered from the security deposit or any other amount/cost involved for the original
contractor. 10% bill deposit shall be retained till DLP expires.
9. Any tenderer quoting “Free of Cost” for any item of work, the tender shall be rejected.
10. The tenderer quoting “Rebate” on comparative cost or on item of rate will be rejected. Contractor
should thus adjust amount within the quoted rate structure.
11. The splitting of quantity of any item i.e. quoting of more than one rate for the item is not accepted.
12. The contractors are advised to see the site before tendering.
13. The tender must be accompanied by CDR pledged to Dean P&D, NIT Srinagar for the amount shown
against the work. Tenders without CDR will be straightway rejected and released CDR shall not be
accepted.
14. In case the date of receipt of tender happens to be holiday, the same shall be received on the next
working day up to 12 noon.
15. Only JK cement or Khaber Grade 43 shall be entertained for cement works .
16. The competent authority reserves the right to reject any tender without assigning any reason
thereof.
17. All other terms and conditions shall remain the same as given in tender notice/NIT-cumAgreement.
(I/C Ex. Engineer)
N.I.T. Srinagar
ALL THE CONDITIONS ARE ACCEPTABLE TO ME
(Signature of Contractor)
Name: _____________________________S/O : _______________________________
R/O : _______________________________Ph. No: ___________________________
`