Version: July 26, 2010 e l i T l t y d u e n i x o i r V m G e y r r P u x u L DESCRIPTION SURFACE PREPARATION Luxury Vinyl Tile Grout is a premixed stain-resistant grout for use in residential, light-duty, interior installations. Refer to MAPEI’s “Surface Preparation Requirements” document for tile and stone installation systems at www.mapei.com. FEATURES AND BENEFITS MIXING • Stain-resistant • • For grout joints from 1/8" to 1/2" (3 to 12 mm) • Ready to use Note: Choose all appropriate safety equipment before use. Refer to Material Safety Data Sheet (MSDS) for more information. • Mold and mildew resistant WHERE TO USE Ready to use; no mixing is required. PRODUCT APPLICATION 1. Read all installation instructions thoroughly before installation. 2. LIMITATIONS Ensure that all tiles are securely bonded to the floor, without any loose corners. Loose tile will cause loose or cracked grout. 3. If using tiles installed with spacers, remove spacers before grouting. • Do not install over substrates containing asbestos. 4. Apply Luxury Vinyl Tile Grout to one small area at a time (6 to 9 tiles). • Do not use for exterior applications, steam rooms, shower floors or areas subject to water submersion. 5. Pack grout into the joints using a rigid, hard-rubber grout float. • Use only at temperatures between 50°F and 95°F (10°C and 35°C). 6. All joints must be fully filled, and free of gaps or voids. • Do not use to grout exterior installations. 7. Immediately remove excess grout from the tile surface by moving the grout float edge diagonally across the tile at a 45° angle or greater. • Do not seal. 8. The grouted joint surface should be finished flush with the tile surface. • Use for grouting residential light-duty interior installations of luxury vinyl tile Shelf Life and Application Properties* Shelf life 1 year Packaging Scrub the tile with a non-scratch scrubpad (white), applying moderate pressure in a circular motion. 8. Use a damp sponge to wipe off any remaining grout haze. 9. Rinse sponge often and change rinse water frequently. 10. Wash hands and tools with water while grout is still fresh. Product Code Size 5XX75 0.5 U.S. gal. (1,89 L) PROTECTION Approximate Product Coverage per 0.5 U.S. gal. (1,89 L) Tile Size 7. Grout Joint Width 1/8" (3 mm) 1/4" (6 mm) 1/2" (12 mm) 12" x 12" x 1/8" (300 x 300 x 3 mm) 305 to 321 sq. ft. (28,3 to 29,8 m2) 153 to 161 sq. ft. (14,2 to 15,0 m²) 77 to 81 sq. ft. (7,15 to 7,53 m²) 12" x 18" x 1/8" (300 x 457 x 3 mm) 366 to 384 sq. ft. (34,0 to 35,7 m²) 186 to 192 sq. ft. (17,3 to 17,8 m²) 93 to 96 sq. ft. (8,64 to 8,92 m²) 16" x 16" x 1/8" (406 x 406 x 3 mm) 406 to 426 sq. ft. (37,7 to 39,6 m²) 203 to 213 sq. ft. (18,9 to 19,8 m²) 102 to 107 sq. ft. (9,48 to 9,94 m²) • Floor is ready for light traffic 24 hours after the initial installation. • Wait 72 hours before moving any furniture onto or across the floor. • Do not use solvents, grout haze removers or sealers on Luxury Vinyl Tile Grout. * A ctual coverages will vary according to substrate profile and tile type. CLEANUP Immediate Initial Cleanup (for each 6- to 9-tile section) 1. Gently wipe a semi-saturated (soaked but not dripping), square-edged rigid sponge diagonally across the grouted joints. 2. Do not apply downward force to the sponge. Simply move it side to side to dress the joints and loosen excess grout from tile surface. 3. Rinse the sponge often in a bucket of clean water and change the rinse water frequently. Note: All residue and haze does not need to be removed at this point. This step is intended to smooth and even out the joint. Excessive pressure or washing can remove the grout from the joint. 4. Repeat the above process for each 6- to 9-tile section until grouting is completed. Related Documents Reference Guide: Surface Preparation Requirements for tile and stone installation systems RGT0309* * At www.mapei.com Refer to MAPEI’s Material Safety Data Sheet (MSDS) for specific data related to VOCs, health and safety, and handling of product. Final Cleanup (for removing grout haze) 5. Restrict traffic and allow the grout to dry for 24 hours. Statement of Responsibility 6. Spray or lightly mop the surface of the tile evenly with a solution of 1/4 U.S. cup (59 mL) ammonia to 1 U.S. gal. (3,79 L) water, or with an ammonia-based ® cleaner such as Windex . Allow solution/cleaner to rest on the surface from 90 seconds to 5 minutes. Before using, user shall determine the suitability of the product for its intended use and user alone assumes all risks and liability whatsoever in connection therewith. Any claim shall be deemed waived unless made in writing to us within fifteen (15) days from date it was, or reasonably should have been, discovered. We proudly support the following industry organizations: MAPEI Headquarters of the Americas 1144 East Newport Center Drive Deerfield Beach, Florida 33442 Phone: 1-888-US-MAPEI (1-888-876-2734) Technical Services 1-800-992-6273 (U.S. and Puerto Rico) 1-800-361-9309 (Canada) Customer Service 1-800-42-MAPEI (1-800-426-2734) For the most current BEST-BACKED™ product data and warranty information, visit www.mapei.com. Edition Date: June 2, 2010 PR5906 LVTD_F10Evp © 2010 MAPEI Corporation. All Rights Reserved. Printed in the USA.
© Copyright 2018